Reddit reviews 50W 6Ohm LED Load Resistors for LED Turn Signal Lights or LED License Plate Lights (Fix Hyper Flash, Warning Cancellor)
We found 7 Reddit comments about 50W 6Ohm LED Load Resistors for LED Turn Signal Lights or LED License Plate Lights (Fix Hyper Flash, Warning Cancellor). Here are the top ones, ranked by their Reddit score.
a pair of 6 Ohm 50W LED Load Resistors for LED Turn Signal Light Fix or LED License Plate Lights Error Fix.This will solve LED related turn signal lights or license plate light problems such as hyper flashing, no flashing or burnt out bulb indicationswill work on any vehicle and can be connected across the turn signal bulbs or License Plate Lights to simulate the load of a regular filament bulb (2 Amp load).One LED resistor is required for each turn signal bulb or each license plate light bulb.- 2 pc 50 watt 6Ohm Load Resistors + 4pc Quick wire Clip
https://www.amazon.com/gp/product/B004EDF8HY/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
This is for 12V, though. I've seen 12V ones for automotive use, but they get pretty hot even when bolted to metal.
LED's use less power than regular bulbs. Because of this, the lights will blink faster (hyperblink). You need to add a resistor to the wiring for the turn signals to introduce more load which will slow them down.
​
Something like this would work.
https://www.amazon.com/Resistors-Signal-License-Warning-Cancellor-x/dp/B004EDF8HY
There's a hint of blue with 10k but I like that. Switchbacks are dual colored directionals. When youre head lights are on the directionals are white like in the picture and when youre signaling they flash amber. I haven't touched the break lights but I did switch the rear parking bulb with an led so I can see more out of my rear camera.
HIDs: https://www.amazon.com/dp/B00WW0A69G/ref=cm_sw_r_cp_apip_XKwJWwoD6cpcC
Switchbacks and resistors:
https://www.amazon.com/dp/B01DQHIUFK/ref=cm_sw_r_cp_apip_tSt7OArepHsXm
50W 6Ohm LED Load Resistors
https://www.amazon.com/dp/B004EDF8HY/ref=cm_sw_r_cp_apip_zdXio3mK945jP
Back up bulb: https://www.amazon.com/dp/B01MDUEBX1/ref=cm_sw_r_cp_apip_RnGlyaHFGAh6R
http://www.amazon.com/Resistors-Signal-License-Warning-Cancellor/dp/B004EDF8HY
Throw those in line with your positive wire and you will be set
I wouldn't be concerned about getting flush indicators. I would be leery of doing anything that would decrease visibility. You can find some lower profile stalks that will stick out less, but still let you be seen by other drivers.
A word of caution tho, if you're looking to go LED for your signals as I have, while you get a much brighter light, on an older bike it's likely you won't be drawing enough current to activate the relay that makes it flash. This is what happens when a turn signal is burned out and why you get that fast flashing, which is what you will have if you don't get an aftermarket relay or some decent resistors to help.
Another thing you could do, which is what I did, is I rewired my stock turn signals to my brake light as well as installed led turn signals. What this did was allowed it to draw enough current to keep it from giving me the fast flash, as well as giving a dull flash in my tail light. AFAIK it's legal to have a flashing/pulsing/strobing brake light since they sell kits for it. I put the bulbs in the same spot as the brake light bulbs, but I used a few strips of red SMD 5050 in my brake light housing and they're much brighter than stock.
Edit: added link for the type of turn signals.
I had this problem with my thruxton. The resistance in the LED's is too low and it thinks your bulbs are burnt out. Add some resistors in series with the bulbs and it will work just fine.
Edit: Specifically these resistors