Reddit Reddit reviews ARCTIC MX-4 (4 Grams) (Current Edition) - Thermal Compound Paste, Carbon Based High Performance, Heatsink Paste, Thermal Compound CPU for All Coolers, Thermal Interface Material

We found 17 Reddit comments about ARCTIC MX-4 (4 Grams) (Current Edition) - Thermal Compound Paste, Carbon Based High Performance, Heatsink Paste, Thermal Compound CPU for All Coolers, Thermal Interface Material. Here are the top ones, ranked by their Reddit score.

Electronics
Computers & Accessories
Computer Components
Heatsinks
Internal Fans & Cooling Components
Computer Internal Components
ARCTIC MX-4 (4 Grams) (Current Edition) - Thermal Compound Paste, Carbon Based High Performance, Heatsink Paste, Thermal Compound CPU for All Coolers, Thermal Interface Material
WELL PROVEN QUALITY: The design of our thermal paste packagings has changed several times, the formula of the composition has remained unchanged, so our MX pastes have stood for high qualityHIGH PERFORMANCE: With excellent temperature reduction performance, the MX-4 is ideal for CPU and GPU cooling, and other applications between power semiconductor components and heatsinksSAFE APPLICATION: The MX-4 is metal-free and non-electrical conductive which eliminates any risks of causing short circuit, adding more protection to the CPU and VGA cardsHIGH DURABILITY: In contrast to metal and silicon thermal compound, the MX-4 does not compromise over time. Once applied, you do not need to apply it again as it will last at least for 8 yearsEASY TO APPLY: With an ideal consistency, the MX-4 is very easy to use, even for beginners
Check price on Amazon

17 Reddit comments about ARCTIC MX-4 (4 Grams) (Current Edition) - Thermal Compound Paste, Carbon Based High Performance, Heatsink Paste, Thermal Compound CPU for All Coolers, Thermal Interface Material:

u/YaGottadoWhatYaGotta · 15 pointsr/ValveIndex

You might wanna see what AMD does unless money is no concern, then sure, but really still I would wait.

Oh and its pretty easy to put in a cpu, I did it successfully with no help when I was 13, just make sure to use thermal paste.

A youtube video will do fine.

u/kheszi · 4 pointsr/techsupport

Apparently overheating is a serious problem with this model:
https://community.acer.com/en/discussion/494982/calling-all-aspire-v-nitro-2017-593g-owners-thermal-issues-discussion

Replacing the thermal grease shouldn't be too difficult. You'll have to carefully remove the entire fan/heatpipe cooling assembly along with any attached cables, the two processors should be right underneath, to the immediate north and northwest of the memory slot.

While you have the assembly removed, inspect both fans carefully for any signs of dust/fur blockage, especially the ran blades and radiator fins. If you see any debris, you can carefully clean that with canned air or (very carefully) with some alcohol and a pipecleaner or toothbrush. If using air, use one finger to hold the fan blades from spinning - resist the urge to "whizz" the fan with the compressed air or you can easily ruin the fans. Optionally you can remove the fan covers with a jewelers screwdriver and clean them thoroughly.

When replacing the assembly, carefully tighten each of the mounting screws in sequence according to the numbers stamped into the cooling assembly. High quality thermal grease will run you about $7.

https://www.amazon.com/ARCTIC-MX-4-2019-Performance-Durability/dp/B07L9BDY3T

https://youtu.be/Cz4X4f8WeHg?t=727

u/HumanKumquat · 3 pointsr/PS4

This is the guide I used.

They don't have assembly instructions but if you reverse what you did, you'll be fine.

You'll need a Phillips #0, a TR9 security Torx, and some spudgers. I've done it before without spudgers but its a lot easier to remove the bottom case piece with them. You might also need a pair of small needle nose pliers to help pull various power connectors. Mine were on there really tight so I had to use some, but if yours are looser you can probably do it by hand.

In addition you'll need some thermal paste and some thermal pads.

I used Arctic MX4 2019 Edition but any paste from any of the big names like Grizzly, Noctua, or Arctic should work fine. If you want to really get into it, check out this chart. Pastes near the top perform better than those near the bottom, but you can see that there's only a 1-1.5 degree difference in most pastes, so choose something that's priced right for you. The MX4 was only $8 on Amazon so that's what I went with.

Since I went with Arctic paste I also decided to go with this Arctic thermal pad. I bought the 145x145mm, .5 mm thick and they fit perfectly. I just eyeballed the size and cut them with scissors, but IIRC the actual chip is 9mm by 9mm. You'll want to cut them, peel the plastic off both sides, and apply them. I peel off one side, press them onto the chip, then peel off the other with the needle end of a spudger, but I don't know if that's necessary or preferred. It just worked for me.

For removing the thermal paste you can just use 99% isopropyl alcohol. I've used dedicated paste cleaners in the past and while they work fine, the 99% ISO seems to work just as well, and it's cheap as shit. Head to your local pharmacy and they should have some for a dollar or so.


edit

I should mention that you'll want to avoid any liquid metal pastes, as they'll corrode aluminum and the PS4 heatsink is mostly aluminum.

u/geordiesvisor · 2 pointsr/macpro

Total cost was 910ish. My build is a 4,1 2009 flashed to 2010. Intel xeon x5680, 48gb ram 1066 ECC, 4 tb SSD (bought 3, had an extra laying around to make 4), added a USB 3.0 card, and an MSI RX560 2GB GPU.

https://cgi.ebay.com/ws/eBayISAPI.dll?ViewItemVersion&item=174082488738&view=all&tid=2078078862007

https://www.amazon.com/gp/product/B01LZWX6PD/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

https://www.amazon.com/gp/product/B072539VBG/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

https://www.amazon.com/gp/product/B07D998212/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1

https://www.amazon.com/gp/product/B0773ZMVRH/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

https://www.amazon.com/gp/product/B07L9BDY3T/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

I also had a mechanical keyboard, display, and magic mouse prior to the build. So maybe plan on 1200-1300 if you need to buy those and the extra SSD as well. That system from Newegg includes a 1tb HDD though, so you can load it up in one of the hard drive sleds as a storage drive, just don't use it as the boot drive. PM anytime if you have any questions!

u/mayhem-8 · 2 pointsr/mac

Hi, The thermal paste we use at the Apple Authorised Service Provider I work for is this https://www.amazon.fr/ARCTIC-MX-4-2019-Refroidisseur-Dissipateur/dp/B07L9BDY3T/ref=sr_1_4?__mk_fr_FR=%C3%85M%C3%85%C5%BD%C3%95%C3%91&keywords=mx-4&qid=1567774785&s=gateway&sr=8-4. It is much better than the Apple thermal.

The Samsung EVO 860 you linked is an SSD we use for customers Macs, we also use the Crucial MX500, both are good SSDs.

The ram you linked is fine, we use Crucial ram but Crucial ram is normally more expensive.

u/ThunderAnt advice to make a bootable USB installer before repalcing the drive is a good idea as it won't rely on the internet during the install.

If you have the MacBook Pro 13" 2012 non retina then be extremely careful with the hard drive cable as it easily fails https://beetstech.com/blog/prevent-a1278-mid-2012-hard-drive-cable-failure

u/PCwhatyoudidthere · 2 pointsr/pcmasterrace

https://www.amazon.com/ARCTIC-MX-4-2019-Performance-Durability/dp/B07L9BDY3T paste does matter. It's not HUGE but again. Spend the extra $2.

u/NotACatMeme · 2 pointsr/buildapc

https://www.reddit.com/r/buildapc/comments/51gf9d/how_do_you_orderly_remove_thermal_paste_from_a_cpu/

​

Gently and without excess alcohol are the watch words. That thread implies putting the drops on the CPU, while I would wet the coffee filter (with the 90%+ alcohol! not water) before wiping instead.

​

If you have a local computer shop, they'll have some thermal paste and it is probably fine. I've used various kinds of Arctic Silver and the paste that came with a Noctua fan. Amazon has both of these available for one day shipping in my area:

https://www.amazon.com/ARCTIC-MX-4-2019-Performance-Durability/dp/B07L9BDY3T

​

https://www.amazon.com/Noctua-NT-H2-3-5g-Pro-Grade-Compound/dp/B07MXFTNZY

The second one comes with cleaning wipes, though from the reviews it looks like they are just alcohol wipes. If you're already nervous and unsure, the reviews say the wipes work well and it might take some uncertainty out of the process for you.

u/fearlesskiller · 2 pointsr/Alienware

Mhm I see. It just looks all kinda complicated on my laptop because i need to take off like 3-4 layers before actually reaching the cpu, gpu...

Also can I buy that paste on amazon?
Like this ? https://www.amazon.ca/ARCTIC-MX-4-2019-Performance-Durability/dp/B07L9BDY3T/ref=sr_1_2?crid=1S40LGKLPHCKK&keywords=mx4+thermal+paste&qid=1564368491&s=gateway&sprefix=mx4+%2Caps%2C167&sr=8-2

u/mrfinancecracker · 1 pointr/thinkpad

Yep jic got ARCTIC MX4.

u/clupean · 1 pointr/buildapc

Clean the video card: remove the gpu cooler and clear all the dust, clean the thermal compound with alcohol and apply new paste. If it still doesn't work, you can buy a 3rd party gpu cooler.

Thermal paste: https://www.amazon.com/dp/B07L9BDY3T/
GPU cooler: https://www.amazon.com/dp/B005I9IM4E/

u/WATCH_DOGS_SUCKS · 1 pointr/simracing

No problem, glad to help!

> I think I'm going to grab a USB-C to HDMI cable so I can hook my MacBook up to the TV

Quick thing, consider getting a Thunderbolt 3 hub, like this one, for example. These little devices allow you to get the most out of your MacBook's Thunderbolt ports buy expanding them to several supported ports, whilst still including at least one full-bandwidth Thunderbolt 3 port. this way, instead of having to get specific USB-C or Thunderbolt 3 compatible wires or adapters, you could just natively connect whatever wires you have to a hub. There's plenty of options for your to choose from, some of which focus on multi-screen output, some of which focus on data transfer, and some that feature a general-user port selection.

> Do you just play on your MacBook sometimes? [...] What games do you mainly play on MacBook with your wheel?

Personally, I pretty much only play PC exclusives on my Mac. I do play Euro Truck Simulator 2 on my MacBook, but unfortunately, The Thrustmaster T80 and T300 wheels I have aren't compatible with macOS or Linux, so I just use a PS3 controller.

However, I can confirm that the G29 [is compatible with macOS and ETS2](https://www.logitechg.com/en-us/products/driving/driving-force-racing-wheel.html#product-tech-specs, along with other titles on Mac.

> Do you find it gets too hot?

It used to, but not anymore.

This may be a bit more advanced, but you can manage your system's thermal performance. Step one would be to get a fan controller app, such at TG Pro, which is what I use. The main issue with thermal performance with Macs is that Apple tries to keep the fan speed as low as possible, to keep the system as quiet as possible... even to a fault. A fan controller app will let you set your notebook's fan speeds with your own custom settings, so whilst it may definitely get louder, you won't have to worry about it burning from the inside out, or at least not worry about thermal throttling.

Step 2, if you so dare, would be to replace the thermal paste in your MacBook. Apple's stock thermal paste is relatively weak at transferring heat (as a trade off for lasting longer), so you may want to consider replacing it with aftermarket, high-quality paste, such as Artic MX-4. High-quality doesn't mean expensive in this case, as a tube of good paste can have at least 10 uses' worth for 3euro - 10euro.

However, keep in mind that taking apart a 2013 and up MacBook isn't easy, and it can technically void your Apple warranty. But if you do decide to undergo the task, it'll unlock your system's full potential. I've done both of these, and now my system never goes above 90°C under full-load.

> Unrelated side note: The buyers guide and support you provide in this community is outstanding and I'd love to support you by purchasing on Amazon through your affiliate link, if that's okay?

Oh, we don't use affiliate links. All of the Buyer's Guide links are standard URLs, the same as anyone else would get. All of the work I put into the subreddit is unpaid.

I've thought about requesting affiliate links a few times so I could fund community events, but I worry about the conflict of interest, especially for when we get new moderators. I really appreciate the thought, though!

_____

^(I'd totally appreciate a gift card donation, though :P)

u/dillygraf · 1 pointr/pcmasterrace

ARCTIC MX-4 2019 Edition - Thermal Compound Paste - Carbon Based High Performance - Heatsink Paste - Thermal Compound CPU for All Coolers, Thermal Interface Material - High Durability - 4 Grams https://www.amazon.com/dp/B07L9BDY3T/ref=cm_sw_r_cp_apa_i_qvKKDbGSCX4CN

u/Broadbanned · 1 pointr/buildapc

The stock cooler should be just fine if you don't plan to overclock. The stock cooler comes with pre-applied Cooler Master thermal paste, but it's always good to have some in case you need to reseat the cooler or change to an aftermarket one, I'd recommend Arctic MX-4 2019 Edition (8-year paste). The only change I'd do is to a 512GB NVMe SSD with 512MB cache for less.

u/endmysufferingxX · 1 pointr/buildapc

you realize shipping you a 4g object is going to cost at least 11USD regardless of what shipping service I use.

Just spend the 7 bucks on some entry level paste

u/1crazypotato · 0 pointsr/london

Arctic MX-4 2019 Edition - Thermal Compound Paste For Coolers | Heat Sink Paste | Composed of Carbon Micro-particles | Easy to Apply | High Durability - 4 Grams https://www.amazon.co.uk/dp/B07L9BDY3T/ref=cm_sw_r_cp_apa_i_tsA0DbVTCHPXT