Reddit Reddit reviews BW 3.5 Inch TFT LCD Monitor for Car / Automobile

We found 43 Reddit comments about BW 3.5 Inch TFT LCD Monitor for Car / Automobile. Here are the top ones, ranked by their Reddit score.

Electronics
Car Electronics
Car Video
Overhead Car Video Players
Car & Vehicle Electronics
BW 3.5 Inch TFT LCD Monitor for Car / Automobile
Brand New and High quality. Portable 3.5Wide view angle, low illumination. D/N models with photo-sensor. Distance reference marking display. Easy installation.Screen Size: 3.5 inch. Ratio: 4:3 TFT screen. Power Supply: DC 12V.Visible Area: 72mm x 53mm. Power Consumption: 2W. Operating Temperature: 0°C ~ +80°C. Storage Temperature: -10°C ~ +80°C.Video: 2-channel video input. Dimensions: 93 x 80 x 20mm (LxWxH).
Check price on Amazon

43 Reddit comments about BW 3.5 Inch TFT LCD Monitor for Car / Automobile:

u/MicroByte · 82 pointsr/gaming
u/scottbot84 · 5 pointsr/raspberry_pi

Bought [this] (http://www.amazon.com/gp/product/B0045IIZKU/ref=oh_details_o02_s00_i00) on amazon, I would say the resolution is good enough for gameboy emulation or something similar. For a headless install its nice to plug in if you can't get to a command line any other way, which is what I got it for.

u/grem75 · 5 pointsr/raspberry_pi

The screens he is referring to take a regular composite input, they are typically used with car backup camera installations. Only modification is removing the buck converter so they run on 5V.

These are commonly recommended.

I used this one, which doesn't come with a shell around it.

u/aft3rmath · 4 pointsr/raspberry_pi

Alright. Simply put there is not an out of the box solution for this. You would have to first figure out the extra hardware needed for the pi to drive the screen and then you would have to write the code to actually use the screen. That software would essentially have to function as a video driver which is usually used for dedicated hardware.

On top of all that the resolution would be very low and you'd probably have trouble even with a terminal.

If you want a small portable screen for your pi I suggest you get something like this http://www.amazon.com/3-5-Inch-TFT-Monitor-Automobile/dp/B0045IIZKU/ref=sr_sp-btf_title_1_4?s=electronics&ie=UTF8&qid=1374906800&sr=1-4&keywords=ntsc+screen

It can be powered off of 12 volts though reading the reviews suggests that you can power it off as low as 5 volts.

u/NBQ5 · 3 pointsr/RetroPie

Thanks! GBA games perform rather well actually as well as GBC games. I was playing oracle of seasons and it seemed to run great! I couldn't figure out how to use the original gameboy screen so I purchased and modded [this] (http://www.amazon.com/gp/product/B0045IIZKU?psc=1&redirect=true&ref_=oh_aui_detailpage_o03_s00) screen to fit my needs. It only draws about 270-300mA so it's not too power hungry making it a fairly good choice for this project. Unfortunately the resolution is crap and reading the small text in the OS menus is difficult.

u/mntbss · 3 pointsr/DIY

This is the most popular one used in the community
https://www.amazon.com/gp/product/B0045IIZKU/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

It might be the same one OP used as well.

There's a few different versions that people get but here's a wiki.
http://www.sudomod.com/wiki/index.php?title=GBZ_Screen

u/digitalife · 3 pointsr/raspberry_pi

I use this, it's $16.99, but you need something like this to power it.

u/mesamunefire · 3 pointsr/shittybattlestations

http://www.amazon.com/3-5-Inch-TFT-Monitor-Automobile/dp/B0045IIZKU/ref=sr_1_1?ie=UTF8&qid=1344995756&sr=8-1&keywords=3.5+lcd

But you will need a 9V~12V adapter. It runs well on a 9V in this case. I just hooked it up to a breadboard.

u/hexcor · 2 pointsr/consolerepair

I know this is 3 months old.. BUT..

I used this screen in my nomad last week

https://www.amazon.com/gp/product/B0045IIZKU/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

comes with adjustments for brightness etc, fits perfectly where the backlight goes. Also seems to keep the settings after turning off

just know, you're hitting the component video, so it's going to have a muddy picture.

I just got a second nomad from goodwill and fixed it, I MAY keep the stock screen in it until someone can get svideo or rgb to work

u/[deleted] · 2 pointsr/raspberrypi

Actually, when I created my post, I ordered this but yesterday night I received a message from Amazon claiming my debit card was declined and they asked me for a credit card (which I don't have). I will try contacting them when I can.

But back to the subject it's not usb :(

u/ragormack · 2 pointsr/RetroPie

For safe shut downs, charging warnings, and charging status - Adafruit PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C-Purchased from amazon, https://www.amazon.com/gp/product/B01BMRBTH2/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

Shell used-Gametown® Full Housing Shell Cover Case Pack with Screwdriver for Nintendo Gameboy Classic/Original GB DMG-01 Repair Part-White (pick whatever color you want)-Purchased from amazon, https://www.amazon.com/gp/product/B01K1C2L1C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1

Screen used- BW 3.5 Inch TFT LCD Monitor For Car/Automobile – purchased from amazon, https://www.amazon.com/gp/product/B0045IIZKU/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 (side note here is that in order to make this fit nicer, I installed it upside down in the case.

Speak used - uxcell 16pcs 27mm External Magnetic Speaker Loudspeaker 8 Ohm 0.25W, purchased from amazon, https://www.amazon.com/gp/product/B010V4RAAW/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 (do not put ANYTHING on the top of the speaker when you install or it will not work.

Prototyping bread board, I purchased from amazon but it is no longer available at the link.

I used this PCB for the buttons on 1 build, the drill guide is VERY useful for this project. - 4 Button PCB For Gameboy DMG-01DIY Pi Zero Made In USA With Grounds and Hole Guide BY:Atomic Market, purchased at amazon, https://www.amazon.com/gp/product/B01JKJCQVM/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1

L-R buttons- 100 Pcs 6 x 6mm x 9.5mm PCB Momentary Tactile Tact Push Button Switch 4 Pin DIP, purchased at amazon https://www.amazon.com/gp/product/B008420WOA/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

28 Gauge Wire - Ribbon Cable - 10 Wire (15ft), purchased at amazon, https://www.amazon.com/gp/product/B007R9SQQM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 (I recommend going to a smaller (higher) gauge than 28. 30 or 32 would have made it a lot easer but 28 will do.

Indicator lights, Uxcell a11092800ux0119 Uxcell (Pack of 75), purchased at amazon, https://www.amazon.com/gp/product/B01F0TCXSW/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 (these are totally optional)

Resistors and capicitors (audio), purchased from https://www.taydaelectronics.com Note: heres the guide I used for the audio too! https://sudomod.com/forum/viewtopic.php?t=480

Old Gameboy game cartridge. For aesthetics.
Headphone jack, ebay, https://www.ebay.com/itm/3-5mm-Stereo-Female-Socket-Audio-Jack-5Pin-PCB-Panel-Mount-Connector-PJ325-/400959590673

Volume wheel, ebay, https://www.ebay.com/itm/20pcs-B103-16x2mm-10K-Ohm-Double-Dial-Taper-Volume-Wheel-Duplex-PotentiometerBS/293146992835?epid=11009192051&_trkparms=ispr%3D1&hash=item4440ec20c3:g:NZkAAOSw3h1ZUavq&enc=AQAEAAAB0BPxNw%2BVj6nta7CKEs3N0qUCHDbWKwW7sKftQNu9OoIx7SAZoMMNoO7ZC%2BQU2m6tHizIeixg2Hdk8yQin%2B7yNcIdtTzT%2FneqdaLt1WntvDDMDNnZ9%2BCyBsPWRiKLCNPKdeaaZNnBjMoVA%2F0tK%2BtG7DVLtcUKV1a4ZUD8%2F3Lgu9eesPLoBiXZs77Vo7R%2FDaZVMV%2FquPTyLO%2FBFipuEkim1t7BIMiLOi2P3Z31r4yxIdLUw6SCVesvVeqBQuoKov776Dxzk8pUY7PZvu4Q3ULnqBWmlWXsKXc8iAp9juNxUBFHnDgW6A7iElTGYe0sQRXfFHW73jI62f5aO%2FnqGANNK%2F7KJlu474aR3Gae9%2FJCT%2FwoLqmBb4FfizrUJ6qKEuVeLAi31kJSoJXIv4msi3r0bMNSm2D7FL5DUBr0Bc4xsSPi7KFWI9AhmQjUn%2FsLVysgEKd8QEildi1DULaVOX11bv95PGoXvfAusYXSi5NQZk4oZJHr6QIjXu5w4e9Nd2lFtmG4ZB%2BkqROOwwliad72iafj6cbSLphBAjtWGZQVNbmcdKXG6S8h7cTVqt0aD4oej7%2BlDVihmo%2BV0Rc2MhA9FgkM%2BcyzPd0qc9vHvdxjpQUq&checksum=2931469928353c744c25da8843a496116014d4766745

Micro SD card (16 GB minimum)

Female Micro usb Port, (I know I did buy these but I can’t find the link. I bought female micro usb ports to make charging easier.)

I want to say this is the battery that I used, specifically because after taking the shell off it was the perfect fit inside of a gutted Gameboy Game cartridge-https://www.bestbuy.com/site/mycharge-razorplus-4000mah-portable-charger-for-most-usb-enabled-devices-silver/6292246.p?skuId=6292246

3d printed button wells-http://market.sudomod.com/3d-printed-gbz-button-wells/

Extra buttons-https://www.retromodding.com/collections/gameboy

Screw bracket-http://market.sudomod.com/3d-printed-gbz-screw-bracket/

I got A LOT of buttons, glass screen shields, the other three builds button PCBs, some stickers, seriously a lot of stuff from https://store.kitsch-bent.com/ his store is unfortunately closed as he has had life catch up to him and has some shit to attend to. If he comes back online show him some love.

Stuff I got from kitsch
PCB board with LR input points
Buttons for X/Y (you can opt to just get replacement snes or an extra set of Gameboy buttons.
Glass screen that fit the GB shell after removing extra plastic


And obviously you should have a pi zero/w as well a shit ton of patience.

u/The-Bent · 2 pointsr/raspberry_pi

I have used a 3.5 inch "backup camera screen" from amazon. It is low rez but it has a tiny controller board and runs off of 5v and the component video signal from the pi.

Edit: this one https://www.amazon.com/gp/aw/d/B0045IIZKU/ref=mp_s_a_1_5?ie=UTF8&qid=1511373767&sr=8-5&pi=AC_SX236_SY340_FMwebp_QL65&keywords=backup+screen&dpPl=1&dpID=41qtbKk9UvL&ref=plSrch

u/lukejw6 · 2 pointsr/Cyberpunk

here is a diagram of a night vision goggle setup using This camera and this display. seams like you could get it working fairly easily, if you wanted any thing other than night vision you would have to get a arduino or something.




This is the tutorial the diagram is from.

u/JudasRose · 2 pointsr/raspberry_pi

Is there any way to make this work?

u/Rammid · 2 pointsr/NoStupidQuestions

BW 3.5 Inch TFT LCD Monitor for Car / Automobile https://www.amazon.com/dp/B0045IIZKU/ref=cm_sw_r_cp_apa_i_AbZBCb47R967R

u/scapegoat4 · 2 pointsr/smashbros

You can actually buy standalone screens that are usually used in cars, which can be extremely tiny while still supporting an RCA (red yellow white) connector.

From what I can tell, this is the model Axe is using.

He's right about the lag too; I used something similar back in high school and it was second to a CRT

u/gyroninja · 2 pointsr/SSBM

The one I use is https://www.amazon.com/BW-3-5-Inch-Monitor-Automobile/dp/B0045IIZKU. It says it takes 12v but it works fine with 7.4v. For audio I have an adapter so I can plug my headphones into the av cable audio from the system.

u/flyinb11 · 2 pointsr/SEGAGENESIS

Haven't installed it yet, but I picked this up.
BW 3.5 Inch TFT LCD Monitor for... https://www.amazon.com/dp/B0045IIZKU?ref=ppx_pop_mob_ap_share

u/HerrDoktorHugo · 2 pointsr/raspberry_pi

Hey! I've been using this rearview screen with a Pi for a bit because I had it from another project. It's juuust unsatisfactory enough for me to say you shouldn't go for a teeny tiny screen like this model unless you're only going to use the text console, and you're willing to do some configuring to make it legible.
I suspect that something like the 7-inch screen would have a better resolution and be more tolerable.

u/anko47 · 2 pointsr/DIY
u/rondhi · 1 pointr/raspberry_pi

http://amzn.com/B0045IIZKU

Also you can use this to power the board if you're powering directly from the Raspberry Pi. https://www.raspberrypi.org/forums/viewtopic.php?f=41&t=17651&start=339

u/StopPlopAndRoll · 1 pointr/RetroPie

I used this one. It's cheap and it works but you need to solder it so it can run on 5v. https://smile.amazon.com/gp/aw/d/B0045IIZKU/ref=mp_s_a_1_4?ie=UTF8&qid=1504033324&sr=8-4&pi=AC_SX236_SY340_FMwebp_QL65&keywords=3.5+inch+backup+camera&dpPl=1&dpID=41qtbKk9UvL&ref=plSrch

The screens inside aren't all the same so if you check over at www.sudomod.com there is a thread in the forums showing where people have soldered them based on the different guts. Hope this helps!

u/SupeRoBug78 · 1 pointr/raspberry_pi

I'm sorry, I couldn't find it at the time. Here it is though.

u/bfeagans · 1 pointr/RetroPie

In addition to what everyone else said, these resources got me up and running:

http://www.sudomod.com/game-boy-zero-screen-alternatives/ - overview

http://www.sudomod.com/wiki/index.php/Screens - specific options and tutorials

https://www.amazon.com/gp/aw/d/B0045IIZKU - the unit I bought for my handheld. Sudomod says that these devices vary, so you’re not ensured to get the same board I did

My screen runs off of gpio without issue, in any event, I just had to mod the screen following sudomod directions to support 5v.

u/hoowahman · 1 pointr/cade
u/gh5046 · 1 pointr/raspberry_pi

The components don't have to be that expensive.

  • Analog monitor - $18
  • Power supply for the monitor - $8
  • Keyboard - $9
  • No mouse is required - $0
  • 4GB SD card - $7
  • Case - $9
  • Raspberry Pi - $35
  • USB wall charger (can power four units) - $8
  • 6ft Micro USB cable - $1.50

    With this configuration you're looking at ~$96 per seat, about half of your estimate.

    When the Model A comes out the price will come down another $10. I'm sure even cheaper new components could be found and more savings could be had if used components were purchased or received as donations instead. It could be possible to get to the $50 level.
u/jebix666 · 1 pointr/raspberry_pi

You can also pick them up pretty cheap on amazon.com, I got one that was 3.5inches for $15. but they have a larger one for only a bit more.

http://www.amazon.com/3-5-Inch-TFT-Monitor-Automobile/dp/B0045IIZKU/ref=sr_1_2?ie=UTF8&qid=1375819632&sr=8-2&keywords=3.5inch+screen

u/themackster · 1 pointr/raspberry_pi

How would you power a car monitor like this

u/irreligiosity · 1 pointr/DIY

You're much better off buying an lcd with video input built in, that one is $17 on amazon and would be easy to wire up.

You'd probably end up spending more money trying to go the more DIY route and buying an LCD and LCD controller. I'm pretty sure Arduino has a way to hook up LCD though if you are so inclined.

u/mmichaeljjjfoxxx · 1 pointr/raspberry_pi

I think a lot of people use this one for handheld gaming projects. It's a little bigger than you said and uses av instead of hdmi.

u/TreeFitThee · 1 pointr/raspberry_pi

I picked up this 3.5"
LCD
from Amazon. Unfortunately, I clicked buy before I measured. I think the biggest that will fit is 2.8". I'm currently looking for another option without having to spend double for the 2.8" touch screen Adafruit has to offer (since I don't care if it's touch screen).

I have not yet figured out how I'll do controls. I was going to wait until the blog author posts an official parts list. In the mean time I was going to pair it with my 8bitdo SFC30 controller.

u/EOMFD · 1 pointr/RetroPie

It's this one from amazon https://www.amazon.com/BW-3-5-Inch-Monitor-Automobile/dp/B0045IIZKU you might have to modify it for it to work with 5volts

u/skitz0h · 1 pointr/raspberry_pi

wait so this one you linked OP https://www.amazon.com/3-5-Inch-TFT-Monitor-Automobile/dp/B0045IIZKU/ref=sr_1_2?ie=UTF8&qid=undefined&sr=8-2&keywords=3.5%22+monitor

the red is the power source and then it just has one audio wire ( white and the yellow being video ? )

u/Dirtbagx · 1 pointr/Gameboy

I've bought through Ebay, bc robotics, aliexpress, banggood etc...

Most small parts like tactile buttons, power switch, volume wheels, rubber membranes, gameboy shells, and buttons were bought from ebay/aliexpress. Long shipping times but cheap prices.

I also bought the custom button PCBs from eBay. Although I did get one all in one board from Helder at sudomod.com
http://www.ebay.com/itm/232363938160

I bought my power boosts from banggood for a few dollars (works the same as adafruits but much cheaper)
https://m.banggood.com/37V-Liion-Battery-Mini-USB-To-USB-A-Power-Apply-Module-p-928948.html?p=9B1915347037201311DI

I bought 1 screen from Alibaba and two from geatbest. I prefer the gearbest screens. You can also find some 23$ screens on Amazon with prime shipping too. Which apparently will work.
http://m.gearbest.com/development-boards/pp_29447.html

https://www.amazon.ca/dp/B0045IIZKU/ref=cm_sw_r_cp_apa_nkSqzb14CJP3C

As for the batteries, amplifier, speakers, etc...i bought from BC robotics online store. You can get adafruit parts from them. Still expensive, but shipping isnt bad if you are buying lots. Plus they have a 5$ shipping promo on now. you can also find cheaper batteries on ebay, or like I did in one build i used a 9$ galaxy note 3 battery.

http://www.bc-robotics.com/products/

I've bought my pi zero's from the pi hut. They seem to have them in stock often and cost about 20 CAD after shipping and conversion:

https://thepihut.com/products/raspberry-pi-zero-w?variant=30332705425
(Seems they are sold out now)

That's all I can think of now. Let me know if you have any questions. Also browse through the sudomod.com forums or wiki for tons of info.

u/uberdalum · 1 pointr/RASPBERRY_PI_PROJECTS

I've had a lot of luck using this tiny little backup monitor off of Amazon. BW 3.5 Inch TFT LCD Monitor for Car / Automobile https://www.amazon.com/dp/B0045IIZKU/ref=cm_sw_r_cp_apa_lhLNybRFJ6ZEE

It's definitely inexpensive, a little cheap too ;)

u/GreekHubris · 1 pointr/raspberry_pi

> I found this https://www.amazon.com/BW-3-5-Inch-Monitor-Automobile
> gets good reviews from pi users

Link is not working for me. I think this is the product he linked to: https://www.amazon.com/BW-3-5-Inch-Monitor-Automobile/dp/B0045IIZKU

u/Im2Nelson4u · 1 pointr/raspberry_pi

off the top of my head around 120-150 but thats assuming you buy everything online with free shipping and assuming you have access to alot of tools.

Pi Zero https://www.adafruit.com/product/2885 $5.00
LCD https://www.amazon.com/BW-3-5-Inch-Monitor-Automobile/dp/B0045IIZKU/ $15.50
USB Sound Card https://www.amazon.com/Sabrent-External-Adapter-Windows-AU-MMSA/dp/B00IRVQ0F8/ $6
USB HUB https://www.amazon.com/Adapter-Converter-Android-Samsung-Transformer/dp/B00OZDUTMM $6
Volume Potentiometer https://www.amazon.com/16x2mm-Double-Taper-Duplex-Potentiometer/dp/B00O9Y6Z70 $6
Mono 2.5w amp https://www.adafruit.com/products/2130 $3
ABXY PCB http://store.kitsch-bent.com/product/common-ground-dmg-button-pcb-a-b-x-y-version $11.75
Power Boost 1000C https://www.adafruit.com/products/2465 $20

Female micro usb https://www.adafruit.com/products/1829 $1
female usb socket https://www.amazon.com/uxcell-Female-Degree-Socket-Connector/dp/B00FH85SGG Free or $6
Stereo Jack https://www.amazon.com/uxcell-Plastic-Stereo-Socket-Connector/dp/B00GLQAF7A $6
Slide switch https://www.amazon.com/uxcell-SS12F32-G7-Position-Switch-Solder/dp/B007QAJWYW $6
Membrane set http://store.kitsch-bent.com/product/silicone-buttons $2.75
Extra button set http://store.kitsch-bent.com/product/custom-buttons $2
28mm Speaker https://www.amazon.com/Metal-Inside-Magnet-Player-Speaker/dp/B00O9YG9GM $6.50
two single button pcb http://store.kitsch-bent.com/product/easy_buttons $4.30
2300mah Battery http://www.microcenter.com/product/458057/2,300_mAh_Li-Po_Battery_and_Charger $15.00

u/Z4ph00d · 1 pointr/RASPBERRY_PI_PROJECTS

I'm working on smth similar right now (link) I doubt that an old lcd will work. Getting the right screen is one of the more frustrating things so far.
I'm gonna get a 3.5 screen meant for parking cameras in a car or smth (Link)