Reddit Reddit reviews CRC 05101 QD Electronic Cleaner - 4.5 Wt Oz.

We found 24 Reddit comments about CRC 05101 QD Electronic Cleaner - 4.5 Wt Oz.. Here are the top ones, ranked by their Reddit score.

Automotive
Car Care
Exterior Care Products
Cleaners
CRC 05101 QD Electronic Cleaner - 4.5 Wt Oz.
Quick drying, plastic safe formula leaves no residueIdeal for applications where lower flashpoing materials can be toleratedNot VOC Compliant for California & OTCHelps prevent contact failureThis item is not for sale in Catalina Island
Check price on Amazon

24 Reddit comments about CRC 05101 QD Electronic Cleaner - 4.5 Wt Oz.:

u/larrymoencurly · 10 pointsr/buildapc

First of all, do NOT submerge the hard drive or even soak it because it is not airtight or watertight but has some tiny holes that can let in liquids. Keep the hard drive and any optical drives dry, and just wipe off their exteriors with a damp paper towel.

To clean the case and electronics, you can use
aerosol electronic parts cleaner that's rated as safe for all plastics, something like THIS (available at hardware stores, auto parts stores, and even Walmart). Do not use other chemicals, like brake parts cleaner, which can dissolve plastics. Hold circuit boards and even the case at slight angles so the liquid will run off and not pool. Spray into the sockets -- DIMMs, PCI-E, USB. Let everything dry very, very thoroughly before applying power again, at least 24 hours. A car parked in the sun with the windows only slightly opened can bake everything at over 100-120 degrees F. Take precautions against generating static electricity, i.e., put the motherboard into a metallic bag (not on it -- those bags are usually anti-static only inside), but to let moisture escape, don't seal it.

u/[deleted] · 6 pointsr/Justrolledintotheshop

Hey electronics guy checking in - it might work again if you spray it down with connector cleaner, and let it air dry on some paper towel. Just be careful not to zap it with static - always touch something grounded to get rid of any static you might have built up before handling the board. When reassembling the ECU, you could try to seal it with some silicone perhaps.

edit: here's some of the stuff.

http://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0/ref=sr_1_1?ie=UTF8&qid=1405784618&sr=8-1&keywords=electrical+cleaner

The dirt and residue that is on the board at the moment can create weak electrical pathways, essentially rewiring the board in a way. It can cause things to done behave has intended. Those are all old school components, which while a bit dated, are usually quite rugged. Give 'em a wash! You can also use rubbing alcohol and a soft toothbrush.

u/herpafilter · 3 pointsr/engineering

This is great advice. The one step I'd add would be, if at all possible, to use a purpose made contact/PCB cleaning spray on the PCB before reassembly. This will safely and effectively remove any conductive deposits left from the water and drive out any remaining moisture. You may find after disassembly that the rubber membrane kept any crap from getting on the PCB, in which case you might be ok without, but you've gotten this far so....

It's not terribly expensive. Amazon is a good example. You can find the same kind of thing locally at a car parts place or maybe even a radioshack.

u/JoshuaJSlone · 3 pointsr/NintendoSwitch

Get some contact cleaner and spray tiny amounts under the flaps on the joysticks. That usually cleans things up and removes the drift. Not permanently, though, because with time it will just accumulate more gunk in there like it did the first time.

u/Unknownlight · 3 pointsr/Games

Dust gets trapped under the analog stick causing it to never properly reset to neutral when you let go. You can fix it with electronic cleaner (use a toothpick or something to lift up the rubber flap under the analog stick to expose the internals and spray).

u/D0esANyoneREadTHese · 3 pointsr/techsupportgore

As long as it doesn't have a screen on it, a can of this will work quite well, it's like keyboard air but better because it's also a solvent (but doesn't dissolve plastic like Brakleen). Don't use it near backlit screens though, it dissolves the glue holding them together and you'll never quite get it looking right again.

u/Ski1215 · 3 pointsr/mazda3

Spray it with a small squirt of QD Electronics cleaner. It's safe and designed for electrical components and you can buy it just about anywhere.

https://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0

u/dragnmastr85 · 2 pointsr/techsupport

Yes. One drop of liquid shorting any traces could permanently damage electronic components. And yes, a motherboard is a very complicated piece of electronics. There is a lot of power regulation on the boards. A single blown cap will render a mobo dysfunctional. Buy this and follow the instructions. You can also buy denatured alcohol to clean circuitry.

u/ss2man44 · 2 pointsr/Gameboy

There exist products that are specifically designed to clean contacts. It's called contact cleaner and it's what I use to clean both cartridges and consoles. Just spray it in the former and insert it into the latter a few times. Dries quickly and leaves no residue.

u/washboard · 2 pointsr/GalaxyS3

Sure thing. This is the stuff I used. You can probably pick up something similar at Radio Shack, Best Buy or better yet a local electronics store.

u/twenty_minutes_late · 2 pointsr/Guitar

Get some electric cleaner like: https://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0

Test it in an inconspicuous are first then douse the hell out of your switch.

Could also be a bad solder joint. Not too hard to fix if you take your time and work carefully.

u/derpotologist · 2 pointsr/electronic_cigarette

I typed up a reply but it seems to have disappeared. Sorry if this is a repost.

It could be anything from trash in the button to the button falling off of the circuit board or a shorted trace. Without seeing the innards, it's really hard to say.

HOWEVER, I've fixed an amazing amount of gear simply by spraying it with contact cleaner.

Take the battery out, get as close as you can to the board, if that's not possible, just spray around the edges of the button from the outside, some cleaner should get in there.

As you're spraying liberally, click the button a ton of times. Something like 50 presses. Give it a minute or two to let the cleaner evaporate (shouldn't take long) and then power it back up and give it a shot.

There's a good chance this will do the trick.

Let me know if it works :)

u/sf_aerial · 1 pointr/Multicopter

If you're not crashing, you're not flying fast enough ;-)

For those of us who crash often into dust/dirt/sand/grass, I recommend the following:

  • Bring a can of compressed air with you when you fly. This will be the first step for removing debris from your mini motors.

  • I REALLY like this plastic-safe electronics cleaner, and it seems to do an excellent job of removing sand [errr, what?] from my motors after I've thoroughly sprayed them out with the compressed air. Most bearings are sealed so you won't need to worry about degrading the bearing lubricant. That being said I try to use as little spray as possible.

    Hope this helps!
u/duckfucker69 · 1 pointr/ps2

They have a good selection and reasonable prices. The TTX brand controllers there are pretty good, not quite as nice as the Sony controllers but they worked with my stuff so far if you want new ones instead of used again. Try taking the controller apart though and cleaning it... http://www.instructables.com/id/Clean-Your-DualShock-Controller/?ALLSTEPS be sure to put the R2 L2 buttons back in after assembly and they will work with out having to try multiple times, they just snap back in after cleaning. Sometimes this works.

Edit:
You could also try contact cleaner with the unit unplugged, spay it into the controller port and controller plug http://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0

So Try,
Cleaning controllers, new controller, cleaning ports, and if those all fail, then its then most likely the system but they are pretty robust as others have stated

u/WardenWolf · 1 pointr/tifu

This stuff should do the job. It's an amazing degreaser, and doesn't leave a mess and won't ruin your flooring. It's entirely clear.

https://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0/ref=sr_1_2?ie=UTF8&qid=1479920047&sr=8-2&keywords=electro+contact+cleaner

u/dankhimself · 1 pointr/pcmasterrace

QD electric cleaner. That stuff will high pressure blast that stuff out. Toth burshwill help dislodge and mix the paste with it. I love this stuff.

http://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0

u/Dragonstar914 · 1 pointr/buildapc

Usually a decent sized hardware store should carry that, at least in the US where I live they do. I know this one works perfectly for it that is on Amazon CA.

u/artist508 · 1 pointr/airsoft

That points to the motor. You can try hosing it out with Plastic safe contact cleaner to see if there is an improvement but you might need a new motor.

u/DonnieJTrump · 1 pointr/MechanicAdvice

Buy yourself a can of this stuff and spray the inside of your connectors. You don't need to get it from amazon, walmart and auto parts stores have it. Let it air dry, should only take a couple minutes. Also check to see if all the pins in the connectors are in good shape.

u/BillNyeDeGrasseTyson · 1 pointr/techsupportgore

Electronics cleaner. It's like a less abrasive brake-clean that's still a solvent and meant for use on electronics.

u/space_reaper · 1 pointr/Vive

If you were to do it, I'd think the linked spray would be what you'd use, NOT WD-40.

https://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0

Edit: There are other cleaners as well.

u/Crimson13 · 1 pointr/razer

You'd have to open up the mouse, and clean the switch with some contact cleaner spray.

Something like this:
http://www.amazon.com/CRC-05101-QD-Electronic-Cleaner/dp/B000CCMLD0/ref=sr_1_3?ie=UTF8&qid=1411762940&sr=8-3&keywords=electronic+contact+cleaner

OR if you're skilled with electronics enough you can just replace the switch itself.

Unfortunately it's pretty common for nagas to fail this way. Buddy of mine had it happen to him too.