Reddit Reddit reviews Crimping Tool Kit, Preciva Dupont Ratcheting Crimper Plier Set with 1550PCS 2.54mm Dupont Connectors and 460pcs 2.54mm JST-XH Connectors for AWG 26-18(0.1-1mm²)

We found 5 Reddit comments about Crimping Tool Kit, Preciva Dupont Ratcheting Crimper Plier Set with 1550PCS 2.54mm Dupont Connectors and 460pcs 2.54mm JST-XH Connectors for AWG 26-18(0.1-1mm²). Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Hand Tools
Crimpers
Power & Hand Tools
Crimping Tool Kit, Preciva Dupont Ratcheting Crimper Plier Set with 1550PCS 2.54mm Dupont Connectors and 460pcs 2.54mm JST-XH Connectors for AWG 26-18(0.1-1mm²)
[Precise and Perfect Workmanship]: This terminal crimping tool is produced with a wire-electrode cutting die set. It can make for a more perfect, precise, and accurate crimp result. It also has a ratcheting mechanism design which can also help you to save energy and strength.[Crimping Size Range]: AWG26-18(0.1-1mm²), it can be used for XH2.54, dupont2.54/3.96mm, KF2510/JST connectors and so on.[1550PCS Dupont connectors and 460PCS JST-XH connectors]: This crimping tool set comes with 1550 PCS 2.54mm dupont connectors, 460 PCS 2.54mm JST-XH connectors and 1.5m 10-wire ribbon cable. You can choose what you need for your work.[High Quality Material]: The crimping tool is made of high quality Alloy Steel and ABS. It creates a sturdy and perfect crimp for DIY electronics, industrial, home improvements and more.[After-Sales Service]: Please read the description and the specifications before you purchase. If there are any problems, please contact us directly.
Check price on Amazon

5 Reddit comments about Crimping Tool Kit, Preciva Dupont Ratcheting Crimper Plier Set with 1550PCS 2.54mm Dupont Connectors and 460pcs 2.54mm JST-XH Connectors for AWG 26-18(0.1-1mm²):

u/ampm24 · 5 pointsr/ender3

Crimping Tool Kit, Preciva Dupont Ratcheting Crimper Plier Set with 1550PCS 2.54mm Dupont Connectors and 460pcs 2.54mm JST-XH Connectors for AWG 26-18(0.1-1mm²) https://www.amazon.com/dp/B07R1H3Z8X/ref=cm_sw_r_cp_tai_ux-PDbBQB65AV

You need a 2.54mm JST connector kit, like this one. Technically you only need the crimper and pins, but it doesn’t hurt to have the full kit. That one also has DuPont connectors which I used for my Pi. You can get smaller kits without. Crimping takes a little practice to get right, but once you get the hang, it’s easy.

u/hellmoneywarriors · 2 pointsr/ErgoMechKeyboards

Crimping kit here:

https://www.amazon.com/dp/B07R1H3Z8X/ref=cm_sw_r_sms_apa_i_gs1JDbV0PC5KM

USB extenders were some AliExpress mystery buy, but you can find them.

u/brynnflynn · 1 pointr/PrintedMinis

Springs:

https://smile.amazon.com/gp/product/B07M7MP2FC/

They're longer than the originals, and much stiffer. We went from having to relevel every print to never touching it once we had it dialed in.

Mirror bed:

https://www.ikea.com/us/en/p/lots-mirror-39151700/

Replaced the glass bed with one of these. Huge improvement over the original bed, especially since it meant we could swap out build plates without touching the leveling. Just unclip, remove old plate, add new plate. Wash with dish soap and water, wipe down and air dry.

Tools and parts for Petsfang:

https://smile.amazon.com/gp/product/B07R1H3Z8X/

https://smile.amazon.com/gp/product/B07DXRNYNX/

https://smile.amazon.com/gp/product/B071WMHNG5/

These and whatever M screw set floats your budget are all you need to print and install the Petsfang.

u/EagleOneGS · 1 pointr/customGCC

Hey, I used this crimping kit from Amazon: https://www.amazon.com/gp/aw/d/B07R1H3Z8X?psc=1&ref=ppx_pop_mob_b_asin_image

The easiest way would be to only use two wires, only connecting the data and a ground (sacrificing rumble). The two pin connector fits nicely. Or if you're determined like I was you can bend the female connector pins of a 4 pin to fit into the header.

I will take a picture of my controllers PCB when I get the chance to show you.

u/TheChrisLick · 1 pointr/3Dprinting

True. Didn't think about the other side, just saw duppnt the dupont and went on auto pilot. 😂

Here is a kit with both!

https://www.amazon.com/dp/B07R1H3Z8X/ref=cm_sw_r_cp_awdo_t1_mJM2Db8YDPD2T