Reddit Reddit reviews Curved Tip Tweezers Cross Lock Jewelers Soldering Tool

We found 2 Reddit comments about Curved Tip Tweezers Cross Lock Jewelers Soldering Tool. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Hand Tools
Industrial Tweezers
Power & Hand Tools
Curved Tip Tweezers Cross Lock Jewelers Soldering Tool
This is a new pair of cross locking tweezersThese are heat resistant and have a fiber grip with curved jawsThey measure approximately 6 1/8" (155 mm) long
Check price on Amazon

2 Reddit comments about Curved Tip Tweezers Cross Lock Jewelers Soldering Tool:

u/Lanceofalltrades · 3 pointsr/chinaglass

Try to find out somehow. You could maybe measure it in inches and do the conversion. As long as the inner diameter of the banger is at least 2mm larger than the insert, it will allow you to grab them with the tweezers. I bought these tweezers and they really make the insert experience worlds easier. https://www.amazon.com/dp/B000OVPG9A/ref=cm_sw_r_cp_apa_th8EAbGSJ0QQF

From what you wrote, I think this would be a perfect solution. And it would only cost around $8. One thing I'll add on carb caps is I have found bubble caps to not work nearly as well with inserts as a directional cap that sits flat and rotates.

u/SunTsu75 · 2 pointsr/diypedals

Seconded, also consider this kind of thing: https://www.amazon.com/Aven-17010-Adjustable-Circuit-Holder/dp/B00Q2TTQEE/ - it's invaluable for PCBs. Just populate from one side, add something to hold stuff in place (like gaffa tape, or bend one lead, or clip on a sheet of paper, etc), turn over the PCB and start soldering away. I wouldn't want to miss mine.

Any soldering iron 40+W where you can regulate the temperature should do, I own a nice station but when I don't feel like breaking it out because it'd take longer to set it up than to do the job I use something like this: https://www.amazon.com/ANBES-Soldering-Iron-Kit-Electronics/dp/B06XZ31W3M/ set to 350°C. Just make sure to clean and tin your tip regularly and it will do the trick just fine Oh, but ditch the solder and get a few spools of good rosin core solder of different gauges, it's not expensive but worth it. In my experience, the solder that comes with kits like that mostly works as a deterrent.

If you're not planning on buying all-included kits also get a few spools of stranded core wire of different colors. You could use solid core wires but those tend to break if they're getting bended from movement without showing it. With stranded core some strands may break but as others don't they'll continue to work. Invisibly broken wires (i.e.) inside the isolation) are a *beeeeep* to debug.

Also, a set of tweezers are great to have, especially the kind that holds stuff together per default, like this one: https://www.amazon.com/Curved-Tweezers-Cross-Jewelers-Soldering/dp/B000OVPG9A/ (only an example, I'd get a tweezers set that contains one like that).

In my experience a tool set like this one is great to have: https://www.amazon.com/Haobase-6Pieces-Double-sided-Soldering-Assist/dp/B01DLX6V3C/ - especially the bending tool is great to have, as it allows eg to bend the leads of a LED without running the risk of breaking the LED itself. It's also great in order to clean up mistakes, helps with desoldering and such

Speaking of desoldering: desoldering braid is a must. A desoldering pump can be useful, too. And yes, practice soldering and desoldering until you can do both without destroying anything.

If you're not going to buy pre-drilled enclosures then you very likely want a) a center punch and b) stepping drill bits. Those let you drill holes in all kinds of sizes without having to buy lots of drills.

Last but not least a wire cutter is a must