Reddit reviews DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed
We found 8 Reddit comments about DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed. Here are the top ones, ranked by their Reddit score.
DC 12V 1/4" Quick connect Solenoid valve.Turn on water when system start;and cut off water when system stop.Working pressure:0.02-0.8Mpa. Its working temperature:32-158℉ (0-70℃).Rated power:4.8W.It will become hot because there are so many coils inside. It’s normal and safe phenomenon. The highest working temperature of this product reaches 60℃. If you want it works long hours, you should find a N/O normally open solenoid valve.
It's actually super easy. Bought everything off amazon.
I'll make a full guide later
You're may be paying many times more sourcing "locally" if you can't wait until chinese new year is over next month. On amazon anything that is 'prime' should be warehoused stateside
Search for
water solenoid
exampleCompatible diameter tube for above example
and any
relay board
example.Moisture sensors are literality just wires shoved into the soil. But beware of electrolyses degrading the metal, you can used galvanized nails or even pencil lead (carbon rods) instead
You shouldn't need a pump unless using a reservoir, but just in case
12V water pump
example--note this has a bigger diameter hose connector you may be able to just shove a 1/4" inside and glue around for seal but look around at the different search results for matching hose diameters all around or possible legit adaptorsAnd don't forget the 12V power adaptor capable of powerint all that. ~2+A should be fine example
I think solenoid valve is indeed the way to go.
You could hook up something like this Amazon link to a relay and a 12v power supply. I guess that particular one gets hot if you power the solenoid continuously for hours at a time, so it might not be the best for you project.
https://www.orbitonline.com/site_files/manuals/200%20Series%20valves%20chart.pdf
The minimum pressure for this valve is 15 psi. I am running my drip irrigation out of my rain barrel, with a pond pump. It doesn't make enough pressure to actuate the pilot in this valve.
I have tried the following valves, that only require 3 psi and they work. I wish there was better option that didn't require a minimum presure.
https://www.amazon.com/gp/product/B016MP1HX0
1/4" push in compression fittings.
I don't like the dash button idea. I do actually have those setup, but the delays involved would add uncertainty about time.
I found this solenoid, so that could work maybe, but Id have to hard a timer somehow. DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normall... https://www.amazon.com/dp/B016MP1HX0/ref=cm_sw_r_tw_dp_x_aqIczbQ7W75MF via @amazon
Can’t help you with programming but you could eliminate the pump and use gravity feed and a valve like this
https://www.amazon.com/DIGITEN-Solenoid-Connect-normally-Closed/dp/B016MP1HX0/ref=pd_aw_fbt_328_img_3/140-4689437-7402416?_encoding=UTF8&pd_rd_i=B016MP1HX0&pd_rd_r=7e732eb6-69bd-4334-8901-5ebb49bc7e82&pd_rd_w=UV8Al&pd_rd_wg=BJTUS&pf_rd_p=0bda97b1-9615-4960-b748-b906a3521083&pf_rd_r=0FX3BC956PNFJ3R82N43&psc=1&refRID=0FX3BC956PNFJ3R82N43
Wow Thanks for the descriptive response!
I'm not very great at electronics, but here is the exact switch I'm using.
As for power source, I'm probably going to use 110 VAC to power the 4 ch relay board. http://www.amazon.com/SainSmart-101-70-101-4-Channel-Relay-Module/dp/B0057OC5O8
This is the solenoid I will be using
Thanks! Your post really helped me think it through. Just need to put it to work lol.
This might be the ticket, because with that type of tubing, I think you want quick connects. I'm not sure about the pressure rating, or if it would be easy to connect to an Arduino.