Reddit reviews Elenco AmeriKit Learn to Solder Kit
We found 23 Reddit comments about Elenco AmeriKit Learn to Solder Kit. Here are the top ones, ranked by their Reddit score.
Learn to solder on the special practice section of your printed circuit board (PCB)Polish your skills on the European siren circuitIncludes: solder, soldering iron and wire cuttersUse for all your soldering tasksAges 12 and up. SOLDERING REQUIRED
https://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA
If you're taking your first steps into wiring, then you should get comfortable working with wires and tools. Here is a kit that will introduce you to wiring, soldering, etc.
Along with that, there are a few tools that might be useful to you:
And there are videos on YouTube that will teach you how to properly solder a wire to a soldering point. For that Elenco kit, the main goal is to get both the siren and the flashing lights to work, which it will if you wired everything correctly and used the correct resistors. It can be easy to make mistakes while learning to solder for the first time but most mistakes can be fixed, and it's very difficult to cause enough damage to render the board completely unusable.
Also, one note of caution: soldering irons are extremely hot, as the intent is to liquify the solder and attach it to the soldering points.
Want to learn to solder without screwing up your bass? Buy one of these kits for like $12 instead. It comes with a cheap soldering iron, good instructions, and a little siren kit you can put together and screw up with no worries. http://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA
something like this
Learn to solder kit complete with iron... $14.81
https://www.amazon.com/dp/B0009Z3JJA/ref=cm_sw_r_cp_apa_i_aVZDDb8TYXTHK
If you're interested in learning to solder, you can get a cheapo beginner's kit for less than $20. These take about an hour or two for a novice to get through. It's a nice card to add to your man deck without investing too much time or money.
No, I haven't actually. But telling people to be careful does no preclude people from being able to do some basic soldering. Because assembling a keyboard is actually pretty low on the required skill level.
If you'd like to learn how to solder, here's a kit you can buy. You'll realize that it's actually quite a fun skill to have, and attempting the assembly of a keyboard might be something you'll learn you're interested in.
http://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA
You should look into a kit like this one
It has a soldering iron, and a bunch of components so you can learn how to solder. Pretty basic stuff.
After that you should look into building a couple of the Velleman kits
Beyond that, it's really up to yourself and what your interests are. Getting a grip of soldering and understanding how stuff is put together is a good starting point.
Learn to Solder Kit
Yep, that's the one (it's partially put together on my kitchen table right now). I'll tell what I bought and let you decide what to get (I overbought since I have nothing to start with). Keep in mind that I am completely new to the RC hobby and this is my first quadcopter build.
laptop screws for the motors
nylon spacer kit
Nylock nuts for the props
Velcro straps
XT60 connectors to make power lead
Wire to make power lead
zip ties
heat shrink
Like I said I overbought but I think this will work for me (for example my batteries have an XT60 connection).
Some other stuff I got because I'm a newb and want my quadcopter to light up the sky:
Helping Hands Magnifier -> this works very well
Learn to solder kit -> it helped me
Pretty lights
Well then, before you take on any Gameboy soldering, you should get a kit like this and practice. The deluxe kit comes with a much better soldering iron though for only $20 more which will last longer. Finally, buy some rosin flux before you mess with the Gameboy, it makes modifying existing solder joints sooo much easier and more pleasant.
Non-mobile version of that link:
http://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA
Main thing I would ask in response is why do you want to avoid Arduino for now? I think the base level of knowledge required to do anything interesting with Arduino projects is a little lower and more condusive to beginners.
There is a cost side of things too. You can get a pretty full Arduino kit for $30. To make much progress on the analog side of things you are going to quickly run into a need for a power supply, function generator, ect.
If you are just wanting to meander through electronics and see what there is to do, I would get that kit or something similar and add in a few op amps and 555 timers.
If you are dead set on avoiding Arduino, then I would either recommend you look into the construction type kits that /u/Susan_B_Good suggested. I had one similar to this when I was starting out.
> Is there such thing as a cheap/inexpensive kit?
Yes, here's a link to one in Amazon:
https://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA/ref=pd_ybh_a_4?_encoding=UTF8&psc=1&refRID=MNYGJG5K180P793GN41W
Soldering is fairly easy, especially if you are just soldering the pins on switches like in that Sentraq kit.
While a better quality iron is nice, you will get by just fine with a basic iron. Here is a basic iron that includes a practice kit.
One way you could help make yourself a valuable part of the team is by learning to solder. You can pick up an entire soldering kit for pretty cheap that will include some practice stuff. Here is an example:
Learn to Solder Kit
Buy something like this and get over your fear of soldering. Basic soldering skills are pretty much a requirement for the next level in this hobby, and it's not too hard. A but if practice with a kit like that and you'll have no problem soldering connectors and PDBs.
Get one of these to practice, it's easy!
You-Should-Solder spiel:
if you have normal fine motor ability, soldering is easier than you think. unless you have an adustable iron turned up to max, or you're holding the iron on the pad for more than 5 seconds, you'll have a tough time ruining the PCB. Check out this comic, watch some youtube videos. If you want some practice before you embark on an expensive project, there are cheap kits you can get online.
I started with this kit. The iron it comes with is about as crappy as you can find, but it's served me very well through many projects, including building 3 keyboards, and unless it breaks or I need to do something very complex with surface-mounted parts, I don't think I'll need to replace it.
The soldering required to build a quad is not very difficult. If you are rusty you can always go to a local hobby shop and buy one of those kits that requires soldering and use it as practice.
You could also just get something like this. - http://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA/ref=sr_1_3?ie=UTF8&qid=1418060308&sr=8-3&keywords=Radio+kit
these kits are cheap and come with irons. http://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA/ref=sr_1_3?ie=UTF8&qid=1332450731&sr=8-3 have fun messing up your first 30 - 50 soldering jobs; we all did.
ok my advise would be to buy the part and also buy some solder practice kits like this https://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA/ref=sr_1_3?ie=UTF8&qid=1523380566&sr=8-3&keywords=learn+soldering and once you feel comfortable solder the part to the drive you should be able to get comfortable after a few hours its not super hard just dont rush.
this is a higly recommended kit. It doesn't include practice with de-soldering but has some practice boards and solder with it. https://www.amazon.com/Elenco-AmeriKit-Learn-Solder-Kit/dp/B0009Z3JJA/ref=sr_1_1?ie=UTF8&qid=1465915944&sr=8-1&keywords=amerikit+soldering