Reddit reviews EvZ 22AWG 4pin LED Electric Wire 22 Gauge 33ft 10m Conductor Extension Cable Line Cord for RGB LED Strip 5050 3528
We found 11 Reddit comments about EvZ 22AWG 4pin LED Electric Wire 22 Gauge 33ft 10m Conductor Extension Cable Line Cord for RGB LED Strip 5050 3528. Here are the top ones, ranked by their Reddit score.
High purity oxygen-free copper with tin-plated, 22awg specification fetures high conductivity, low resistance and soft, can be bent arbitrarily.High purity oxygen-free copper with tin-plated, 22awg specification fetures high conductivity, low resistance and soft, can be bent arbitrarily.Max Voltage: 300V, Max Current: 3.2A, Color: Black\Green\Red\BlueNo need welding, easy to connect and cut.Connection extension for 3528 5050 RGB color led strip, for electronic appliance and equipment, transformer, lamps and motor lead wire connection, led strip light, led splitter connection etc.
So we bought some RGB led's from amazon, auto wire, a switch and [extension wire] (http://www.amazon.com/Color-Extension-Cable-Line-Strip/dp/B00DPQMKBS/ref=sr_1_1?ie=UTF8&qid=1416110978&sr=8-1&keywords=rgb+extension+wire)
Tap into the 12v cig plug(or any 12 volt that turns off with your car) and run it to the power side of the controller box. Then cut the led's to length and use the double sided tape that comes with it to hold it in place out of sight. Solder the extension wire between the driver and passenger side footwells and to the back. The front was easy, however the backseat was harder.
We had to take the seats out in the back to run the wire under the carpet to keep it hidden. Then there's a 1/4" gap where we put the lights. It is on the bottom, where the seat fabric meets the metal frame of the seat.
To run it to the bed, we had to take the plastic storage behind the seat to find a rubber grommet that is on the driver's side behind the seatbelt about 6-9" from the floor. Its a 1/2" rubber grommet that just plugs a hole and has no other purpose. then run the wire beneath the bed.
We took the railing on the sides of the bed(4 torx bolts per side) and then popped off the plastic that sits on top of the bed sides. Using 3M 20lb double sided tape, we attached the LED's to the bottom side of the rails that were removed. Then the wires were run through the holes that hold that plastic top piece in place. Those holes give access to the inner fender wells where the wire was securely zip tied and run to the other side of the bed and the same process was done.
We later found out that the lights in the bed cannot be in their fade mode while the truck was in motion, so we had to run a separate switch to the bed section so it could be turned off independent of the interior lighting.
If you have any specific questions, feel free to PM me and ill call my buddy to take more pictures for you! It was his new truck that we did it to, not my personal car.
Here are the components I got:
RGB LED Strip Lights Kit,BEILAI RGB LED Light Strip Waterproof SMD 5050 DC 12V Flexible Neon Tape 16.4 Ft (5M) 300leds with 44key Controller for Christmas Kitchen Party Indoor and Outdoor decoration https://www.amazon.com/dp/B01KSPR5GS/ref=cm_sw_r_cp_api_p6mWBbZ9XWQ7N
EvZ 22AWG 4pin LED Electric Wire 22 Gauge 33ft 10m Conductor Extension Cable Line Cord for RGB LED Strip 5050 3528 https://www.amazon.com/dp/B00DPQMKBS/ref=cm_sw_r_cp_api_r7mWBbSQEZB0T
EvZ 10PCS LED 5050 RGB Strip... https://www.amazon.com/dp/B01CMLLKHG?ref=yo_pop_ma_swf
12V DC Battery Pack, 6000 mAh... https://www.amazon.com/dp/B00U2PVX36?ref=yo_pop_ma_swf
And a bunch of male/female connectors - but I can’t find the link. Also make power connectors for the power bank.
Soldering was a pain because the led leads are so close together. Used a knitting ring in the hoodie opening to keep it stiff and hot glued the whole contraption onto some black sweats. No time this year but I want to play with Tron type costumes next year.
Just run extension cords behind the wall or within the cabinets. That way stove heat won't be a problem. If you want to save money just buy bulk wire. But if you connect more than 16ft of lights in a single circuit, then you needed an amplifier which needs to be plugged into an extra power supply otherwise the lights near the ends of the circuit will be dimmer and also off color. Color correctness comes from adequate power.
Another idea. Need to have the lights far from the power source? Use this cable with these connectors. A slight bit of soldering (use heat shrink tubing around the solder joints) and you're in the game!
Soldering is a good skill to have and basic soldering irons are very inexpensive. Try it!
Your other option is to buy longer wire and use strip to wire connectors on both ends of the wire.
This is my next project...
https://github.com/steve228uk/homebridge-magichome
SUPERNIGHT WIFI Wireless LED Smart Controller Working with Android and IOS System Mobile Phone Free App for 16.4ft 300 LEDs RGB LED Light Strips https://www.amazon.com/dp/B01JS0KEBW/ref=cm_sw_r_cp_api_XJn-ybKJ9WEBS
Alightings 4pin LED Connector Connect Wire to Strip, Applicable for 10 mm 5050 RGB Waterproof LED Strip Lights, 22 - 20 AWG Cable Without Stripping the Wires https://www.amazon.com/dp/B01I8CDF58/ref=cm_sw_r_cp_api_jKn-ybEXT5PVQ
EvZ 4 Color 10m RGB Extension Cable Line for LED Strip RGB 5050 3528 Cord 4pin https://www.amazon.com/dp/B00DPQMKBS/ref=cm_sw_r_cp_api_yKn-ybSYT4318
EPBOWPT 12V 5A Power Supply AC Adapter for 5050 3528 RGB LED Strip Light Low Voltage Device https://www.amazon.com/dp/B01KT20TNG/ref=cm_sw_r_cp_api_OKn-ybWC82QCH
SUPERNIGHT (TM) 16.4FT 5M SMD 5050 Waterproof 300LEDs RGB Color Changing Flexible LED Strip Light https://www.amazon.com/dp/B00DTOAWZ2/ref=cm_sw_r_cp_api_4Kn-ybSM88NFB
Then you would want this
EvZ 4 Color 10m RGB Extension Cable Line for LED Strip RGB 5050 3528 Cord 4pin https://www.amazon.com/dp/B00DPQMKBS/ref=cm_sw_r_other_awd_p4-NwbH302Q8D
Soldering was simple for mine, it may be a slight headache for the multiple wire, but will look good. I have about 8 feet of wire along with the 16 feet of lights and there isn't an issue, i believe my power supply is 3A. I think i recall someone said they had 4 of them on a 3A supply without any issues. I would advise a drop of hot glue at the soldered ends to keep the weight of the wire pulling everything down.
No problem.
I was also looking at an alternative solution from another reddit post which would use the following items:
If this makes sense then it would look something like this?
LED strip --> strip connector --> 10m extension cable (through ceiling) --> strip connector --> LED strip for cabinets on other side of wall
Found a very informative video of the ballast + LED strips + hue bridge: https://www.youtube.com/watch?v=VNfa9X5Sq1Q
That's already $93 + tax so if it makes more sense to just get a refurb hue strip kits and synchronize them to the same room (Kitchen) then I guess I will go with another set of hue strip kits.
When things settle down for me too, maybe :) money's tight but eventually if theyre still there when i can, i will.
We also bought the connector clips (so it can bend around corners and stuff), extra wire (for extra length), and connector ends (for the extra wire).
The whole thing is super easy and quick to put up! As a warning, the peel and stick backing isn't good at all, so i would recommend buying stuff to help it stay. We used sticky tack since it doesn't hurt the surface so we can take it off if we need to. We left it on a long time (6 hours) and it barely heated up at all. Just about as warm as a starbucks coffee cup. As long as it's not on all the time it shouldnt heat up at all
I think I may heed your advice and get some RGB ones.
As for your comment on soldering, I am a little nervous about that. At least at my newbie status with all of this. Do any of these do the same thing?
EvZ 4 Color 10m RGB Extension Cable Line for LED Strip RGB 5050 3528 Cord 4pin
Zitrades 10PCS LED 5050 RGB Strip Light Connector 4 Conductor 10 mm Wide Strip to Strip Jumper
4PCS 2M 6.56ft 4 Color RGB Extension Cable LED Strip Connector Extension Cable Cord Wire 4 Pin LED Connector for SMD 5050 3528 2835 RGB LED Light Strip ( 4 PCS )
Bought them from Amazon for less than $20. Also bought extra RGB wires that connect the cut stripes behind the shelves. Plus Silicon Clips incase the tape wears off.
Closer Image of Right shelf