Reddit reviews Glock 03374 Disassembly Takedown Tool for Pin Punch
We found 7 Reddit comments about Glock 03374 Disassembly Takedown Tool for Pin Punch. Here are the top ones, ranked by their Reddit score.
Glock disassembly toolBlack finishThe tool measures approximately 3 5/8'' from end to end
One tool
https://www.amazon.com/gp/aw/d/B0014VX2M2/ref=mp_s_a_1_3?ie=UTF8&qid=1525899651&sr=8-3&pi=AC_SX236_SY340_QL65&keywords=Glock+tool&dpPl=1&dpID=21dVWV7qV6L&ref=plSrch
Just get a takedown punch.
The awesome thing is that Dawson supplies the tools you need for both the front and rear sights.
I would say that a bench vice is required though. Took quite a bit of hammering to install the rear sight. I clamped the slide in between two wooden blocks wrapped in duct tape, and wrapped the included punch tool in duct tape as well. Managed to install everything without marring or scratching the finish.
Not sure what you mean by trigger tool. If you mean the pins, I've found that this disassembly tool works great for a bunch of stuff, but any pin punch should work fine if it's small enough.
As far as brands go, I would take a look at Agency Arms, Overwatch Precision, or SSVI. Those brands in my opinion all appear to be the safest in terms of drop safety for after market triggers.
You should be able to install the trigger yourself using only a Glock Tool (IE: Do not use a hammer ever to do this!) which is literally just a small handy punch or really any punch of the same size for that matter.. There are plenty of videos on youtube on how to do this. The trigger will come assembled on to the trigger bar already, so when you replace it, you will be replacing the entire trigger bar / trigger shoe assembly. Its not really that hard.
Glock 03374 Disassembly Takedown Tool for Pin Punch https://www.amazon.com/dp/B0014VX2M2/ref=cm_sw_r_cp_apa_i_Kw80Bb4VNE36H
He's only posted dick comments that I've seen. Don't pay him any mind. As far as the trigger, it's really easy. Buy a punch for 6 dollars (Glock 03374 Disassembly Takedown Tool for Pin Punch https://www.amazon.com/dp/B0014VX2M2/ref=cm_sw_r_cp_apa_1q5YAb2W9YKPA) and watch a video. It's way more easy than you think. Make sure the gun is unloaded and do the work in a room with no ammo nearby. When you remove the trigger pin make sure you don't hammer it too much. Wiggle it around, usually toward the nose of the gun, and it will press out. Pull the trigger forward and twist and the crucifix comes out, unhook the spring and put it on the new trigger and do everything again in reverse. Took me 4 minutes the first time I did one. As long as you don't hurt yourself, you can't really hurt anything by trying
Leave the copper colored factory grease on the slide until it's gone. Hit up the range with a few hundred rounds. Some people clean the gun before firing. I just lubed the slide a little and fired 300 rounds before my first cleaning.
Start here: https://youtu.be/DZf4mUM10Vc
For deeper cleaning watch this: https://youtu.be/7VTIqAMPOco
These: The Professional's Choice Pistol/Rifle Cotton Flannel 2 1/2-Inch Square Gun Cleaning Patches (120-Pack), .38/.357-Calibre/9mm/10mm https://www.amazon.com/dp/B003MY45Q6/ref=cm_sw_r_other_apa_I0Erxb77YVTWA
-This: UTG 9MM Pistol Cleaning Kit https://www.amazon.com/dp/B002ZJ1364/ref=cm_sw_r_other_apa_j1Erxb6MQEHNV
Sorry for the long links I'm on mobile and bored at the moment. There are more updated and thorough videos if you search YouTube, but I enjoy listening to Hickok45's. Hope this helps.