Reddit reviews Hooshion USB Flight Simulator FMS Cable for RC Helicopter Airplane Remote Controller

I got an Eachine 250 racer about a month ago. It has been a lot of fun, but there are a lot of details. My next racer will probably be a smaller/lighter 180 frame.

For FPV goggles I have three ideas. One, is get the status quo Fatshark goggles at whatever level you can afford. Two, get the HeadPlay HD goggles I got. Three, get the Avegant Glyph, which has the really nice feature of letting you pop them up and down without a band. I do really like my HeadPlay HDs, but they are big and bulky. I haven't perfected how to adjust the straps to get them to stay on my head well.

Arms, managed to break one without breaking a prop.

http://www.amazon.com/gp/aw/d/B016Y5U1JO/ref=ya_aw_od_pi?ie=UTF8&psc=1

Capacitors, they pop off very easily. I lost a capacitor at the same time I broke an arm. Or a hot glue gun, I Highly recommend putting hot glue over the caps next to each arm to help avoid the loss in the first place. You want a low temperature hot glue gun to not melt any plastic or traces. I consider the capacitor issue a design defect, but you can work around it with hot glue. The original revision seems to have lacked the capacitors, from pictures I have seen online.

Capacitors for Eachine 250 racer:
http://www.amazon.com/gp/aw/d/B00W8YYMZA/ref=ya_aw_od_pi?ie=UTF8&psc=1

Youtube video exampling how to solder them:
https://www.youtube.com/watch?v=sLYVZUpL0K0

Get a Taranis X9D Plus. It is a great transmitter. Also get a X4R-SB receiver, and use SBUS. The D4R won't let you control the lights too, because it can't do PPM and PWM at the same time. You can control them with the X4R-SB, SBUS+PWM. SBUS has great latency, 5-10ms. I was recently talking to a sponsored racer who told me that PPM, which is supposed to be 27ms with the D4R, is really more like 100ms. It averages the four last frames together. This link includes a case and X8R, which I think will work as well as the X4R, but you should do the research. http://www.amazon.com/gp/aw/d/B014IYSXL6/ref=mp_s_a_1_5

To do SBUS+PWM, requires a special bind procedure. You want channels 1-8 as SBUS, and 9+ as PWM. The most relevant part is "jump S1&S3: SBUS, 9, 10, 11 or jump S2&S3: SBUS, 9, 10, 11 (No telemetry)" Here is a link that talks about it.

http://www.frsky-rc.com/BBS/viewtopic.php?f=4&t=6793

Small tie wraps like the ones already on the arms to hold the ESCs. You break an arm, and you will need to replace the tie wrap.

Soldering iron, solder, etc, because you have to desolder the ESC from the motor to replace an arm, and then resolder it.

http://www.amazon.com/gp/aw/d/B000BRC2XU/ref=ya_aw_od_pi?ie=UTF8&psc=1

Qtips and rubbing alcohol for cleaning. Mix the alcohol 50/50 with water. The flying field was muddy after lots of rain.

Carrying case of some kind. You don't want it banged around in transport, and same with the transmitter. It is best to get the X9D with the case, because people price gouge on the case stand alone.

http://www.amazon.com/gp/aw/d/B01ABQS7YI/ref=ya_aw_od_pi?ie=UTF8&psc=1

Batteries, you can burn through them very fast. But watch out for their height. I bought some of the new "Graphene" 4S batteries, and they are really too tall to fit. Some people remove the back LEDs to make battery installation easier.

Battery charging/carrying bags to help with uncontrolled fires started by batteries. I have two, one for charging, and one for carrying.

http://www.amazon.com/gp/aw/d/B005HTH78W/ref=ya_aw_od_pi?ie=UTF8&psc=1

A battery charger if you want to use 4S batteries. The included charger is 2S/3S only. I have a Hi-tech X1 which will only charge one battery at a time. You can also get the X4 which will do four at once.

Battery charger for 4S batteries:

http://www.amazon.com/gp/aw/d/B005LH3392/ref=ya_aw_od_pi?ie=UTF8&psc=1

XT60 banana plug cable for charging with the above charger:

http://www.amazon.com/gp/aw/d/B00XBSBYCG/ref=ya_aw_od_pi?ie=UTF8&psc=1

A V shaped antenna mount to get the receiver antennas up in the air. When over head the carbon fiber body blocks the signal well.

http://www.amazon.com/gp/aw/d/B00WV04P62/ref=ya_aw_od_pi?ie=UTF8&psc=1

A voltage monitor so you know to land when your battery voltage is low. The video signal includes the battery voltage as part of the OSD, but I prefer LoS while learning to fly. It lets me keep an eye on where I am in relation to trees. On the other hand I have yet to find a good place to mount a voltage monitor. With the length of the balance cable on batteries you are likely going to need a balance cable extension for 3S and another for 4S.

Voltage monitor:

http://www.amazon.com/gp/aw/d/B00EXPPF80/ref=ya_aw_od_pi?ie=UTF8&psc=1

3S balance cable extension:

http://www.amazon.com/gp/aw/d/B00XP4IO88/ref=ya_aw_od_pi?ie=UTF8&psc=1

4S balance cable extension:

http://www.amazon.com/gp/aw/d/B00JBP1RGG/ref=ya_aw_od_pi?ie=UTF8&psc=1

Double sided tape to mount things on the top of the body, like the antenna mount and receiver.

http://www.amazon.com/gp/aw/d/B009NP1JQC/ref=ya_aw_od_pi?ie=UTF8&psc=1

Small x-acto knife to help remove the double sided tape.

Electrical tape to tape down wires for lights and receiver.

Size 2.0 hex wrench for the frame screws. It will be needed to replace arms.

Scale that can measure grams. You want to knowing and control weight.

http://www.amazon.com/gp/aw/d/B010HKEDPK/ref=ya_aw_od_pi?ie=UTF8&psc=1

Sunglasses to avoid problems seeing on sunny days. Lets say you are flying LoS, and look into the direction of the sun. You can't see the quad well enough to control it, because of glare from the sun.

ESC flashing adapters to change/upgrade the firmware. I am not sure these are the right ones for the ESCs on the Eachine. I think they are, but I haven't tried it yet.

Atmel socket flashing tool:

http://www.amazon.com/gp/aw/d/B00V2W467I/ref=ya_aw_od_pi?ie=UTF8&psc=1

Atmel USB programmer:

http://www.amazon.com/gp/aw/d/B0051SRZWC/ref=ya_aw_od_pi?ie=UTF8&psc=1

USB cable to use with transmitters and simulators. It is best to learn the basics in a sim, instead of replacing lots of parts.

USB cable for simulators:

https://www.amazon.com/gp/aw/d/B00DFDTU9G/ref=ya_aw_od_pi?ie=UTF8&psc=1

Old post of mine on learning in a simulator:

https://www.reddit.com/r/Multicopter/comments/3zr8o0/cheap_fpv_acro_simulator_with_real_transmitters/

Be sure to set a fail-safe, which is very easy with the Taranis. I had a fly away with my first Eachine, because of a defective Spektrum DX6 and lack of fail-safe. After that I switched to the Taranis, which doesn't cost much more and has way more capacity.

You need a cable that accepts that jack and turns it into a USB. http://www.amazon.com/gp/aw/d/B00DFDTU9G/ref=mp_s_a_1_1?qid=1415311319&sr=8-1&pi=SL75

No it does not. https://www.amazon.com/Hooshion%C2%AE-Simulator-Helicopter-Airplane-Controller/dp/B00DFDTU9G/ref=sr_1_2?ie=UTF8&qid=1465605564&sr=8-2&keywords=simulator+cable

> http://www.amazon.com/gp/product/B00DFDTU9G?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00

This cable works for me too.

I have a flysky fst6 that I could use a trainer plug/cable with.I wont have any time to fly this summer but will have some time this winter to try some sims.

Ths should do the trick with my flysky

http://www.amazon.com/gp/product/B00DFDTU9G/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

Like I said my taranis has no usb.

I use this for a different transmitter. It'll work if it has a trainer port in the back. https://www.amazon.com/gp/aw/d/B00DFDTU9G/ref=pd_aw_sim_sbs_21_1?ie=UTF8&psc=1&refRID=4NJFBCJBC7AX5BA7E75Q

I have the turnigy, it's cold here and also I'm just building my first racing quad and want to train. Is it this cable? http://www.amazon.com/Hooshion%C2%AE-Simulator-Helicopter-Airplane-Controller/dp/B00DFDTU9G/ref=sr_1_fkmr2_1?s=toys-and-games&ie=UTF8&qid=1453490396&sr=1-1-fkmr2&keywords=USB+Flight+Simulator+FMS+Cable+Set