Reddit reviews Hosa YPP-111 1/4" TS to Dual 1/4" TSF Y Cable

I bought this guy, so I can plug into rocksmith and my amp at the same time. It works great!

Huh, that's a pretty basic trick. Get a signal splitter, connect it to the guitar and plug an instrument cable into each end. Connect one of them to the amp, and another to whatever mechanism you use for getting the signal to the headphones. Alternatively, you can do the same thing but with only one instrument cable coming out of the guitar, connected to a female-to-female 1/4 jack coupler with the splitter attached, and with the two cables connected to the splitter. This way you'll need a coupler and an additional cable, but the cabling from the guitar won't be as annoying.

But that's usually meaningless, since pretty much any venue with loud music nowadays will give you in-ear monitors.

One thing you can do is buy one of those single-preset portable amps (like this one) and attach it to one of the ends on the splitter in place of the instrument cable, then plug your headphones in it. This way there won't be too many unnecessary cables, and the signal you'll get in your headphones won't have to be unprocessed DI.

Hosa YPP-111 1/4" TS to Dual 1/4"... https://www.amazon.com/dp/B000068O53?ref=ppx_pop_mob_ap_share

Or an ABY box, maybe one with a volume to handle the line level vs instrument level, I dunno if that’s gonna be a problem or not.

Or Behringer micromix I have one of those

Edit. https://www.oldbloodnoise.com/pedals/signal-blender

This would def work

I use one of these: https://www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53 at home currently with a laptop with no issues. I had to switch around the outlets that the amp and laptop were plugged into until I was able to get the hum to stop. I do have some problems where the sound will crackle if I move around too much though.

You can also try the instructions on this link: https://www.reddit.com/r/rocksmith/comments/3hdnte/how_to_get_rocksmith_and_your_amp_working/

Sorry, I'm still new. Would something like this work? https://www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53/ref=pd_sim_267_6?_encoding=UTF8&psc=1&refRID=KNMZ5JMVFNNHAZT62X31

That's not a bad question at all! You can have luck with a very simple Y cable - but for me, it produced lots of noise because it's not separated (Current can flow freely between your PS3, guitar and amp).

I am right now using this, so a pricier signal splitter that grounds the signal.

It does definitely pay off; even more so if you can use the cheap cable!

I'm still not getting it... It's basically a bypass looper without a bypass switch? How does having this extra pedal save space on the pedal board? If the point is to have two signals merging into one, why not use a signal splitter like [this] (https://images-na.ssl-images-amazon.com/images/G/01/musical-instruments/detail-page/B000068O53_img1.jpg)?

You are way over-thinking this. You don't want to change the signal that goes to the PC. You want as clean of a signal as possible to allow for better note detection.

Get his splitter Link and plug the Real tone cable into one output and run the other through your signal chain to the amp.

In the game set your guitar sound to almost zero so that the only thing you hear is what comes out of the amp. As far as pedals and amp, that's going to depend on what type of music you plan on playing. Amp and pedal selection is as all determined by personal preference.

I just use something similar to this. It's much cheaper.


www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53

T/S to dual T/S

https://www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53

https://www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53/ref=sr_1_1?ie=UTF8&qid=1465850103&sr=8-1&keywords=1%2F4+splitter

one of those with a female to female coupler on the male ends of the slitter and the RT cable would do.

No, unless the tip and ring are grounded shorted somehow. Something like this plugged into the mixer

https://www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53/

plugged into this then the 1/4" stereo headphones (vary as needed for 3.55mm phones)

https://www.amazon.com/Hosa-YPP-136-Stereo-Breakout-Cable/dp/B000068O5D/

so the jack sees a TS unbalanced connector.

I'm sure there is a ts 1/4" to TRS stereo single adapter that will do the same thing somewhere/

!

You would connect monitors to left and right output on the back of the UMC202HD. But because you are only using one channel of the two on the front, it will only output to the left speaker.

You'd have to use a DAW to have it be heard in mono or...

Use an adapter like THIS to duplicate the single mono to dual mono and plug it into both inputs for direct monitoring in both headphone ears.

TS splitters such as this one are available: https://www.amazon.com/dp/B000068O53/

However, the signal will most likely be about half the volume when both devices are plugged into the splitter. You could turn up the gain on both your monitors and your mic, but it's hard to say whether that will result in useful volume levels.

get yourself one of these.
http://g-ecx.images-amazon.com/images/G/01/musical-instruments/detail-page/B000068O53_img1.jpg

plug your guitar into one jack, plug an 1/8" to 1/4" adapter for your metronome into the other jack, and plug the main jack into the single input on your pod. You'll have both the metronome and guitar signal coming through your pod. Problem solved.

Here it is on Amazon: http://www.amazon.com/gp/product/B000068O53/ref=oh_details_o02_s00_i00

Update in the OTHER direction from me. I was using only the PC mic forever, but then when I got the the level 7 test, my mic just absolutely couldn't figure out the FMaj13 chord. No matter what, I was getting red notes. Switched to the rocksmith cable, and it worked fine. I used my acoustic/electric so I could hear myself play. I never had a problem with the mic and single notes but some of the "fancy" chords could be difficult for the mic to pick up all the different notes.

edit: I'm buying a little Y cable (this one: https://www.amazon.com/gp/product/B000068O53/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1)
to be able to use my electric with the amp and rocksmith cable at the same time. I'll let you know how it works out.

Splitters are probably cheaper than buying a pedal.

splitter cable for 5$.

This is my setup for recording using a portable audio recorder in the C152's I'm training in.

I use a 1/4" 1 male to 2 female Y-splitter that goes into the headset plug in the plane. One of the split ends will have the headset plugged into it.

The other split has a 1/4" to 3.5mm adapter, which I have a male-to-male 3.5mm cable plugged into. The other end of the 3.5mm cable is plugged into the audio-in port of a portable audio recorder. Total cost of the cable setup is about $15 CAD, most of the cost being the Y-splitter.

You only need to plug into the headset plug in the plane, not the mic, as your mic will be mirrored to your headset anyway so you can hear yourself speak.

Quick search on amazon I did to try to find suitable products:

1/4" Y-splitter: http://www.amazon.com/dp/B000068O53/

1/4" to 3.5mm adapter/cable: http://www.amazon.com/dp/B000068O3D/

The Y-splitter is mono as most older planes will be mono. The cable is mono to stereo so it'll send the mono audio to both stereo channels in your recorder.

I was thinking using something like this - http://www.amazon.com/Hosa-YPP111-inch-Female-Cable/dp/B000068O53

Hmm, so could I just buy this, then it would work? https://www.amazon.com/Hosa-CPE-112-Right-Angle-Guitar-Patch/dp/B0010D4OOY

Or would it be better to buy a splitter?https://www.amazon.com/gp/aw/d/B000068O53/ref=pd_aw_sim_23_3?ie=UTF8&dpID=41Y6BloVuqL&dpSrc=sims&preST=_AC_UL300_SR300%2C219_&psc=1&refRID=QSGZ5D6DS5MJS0RFQMR9

It's a mono cable, this one to be exact. I've been using it like that minus the SwitchBlade for the past few minutes and it seems to work fine, I just wasn't sure if I was risking damaging the pedal by forcing too much signal into it or something like that.

I use one of these https://www.amazon.com/Hosa-YPP-111-inch-Dual-Cable/dp/B000068O53

Plug into guitar out and connect a regular cable to amp and the realtone cable to ps3.

No more lag.

I use this: Hosa YPP-111 1/4 inch TS to Dual 1/4 inch TSF Y Cable https://www.amazon.com/dp/B000068O53/ref=cm_sw_r_cp_apa_J.UKxb5REJ4YJ

And send the output of my guitar to the pc and to the amp...this way I can hear just my instrument.

Yes, depending on your pedals. You'd need a delay with a wet/dry knob and a volume pedal with a tuner out.

Run the volume out into the delay and set the delay pedal to 100% wet and whatever settings you want when it's maxed out.

Grab one of these y connectors from Amazon. Hosa YPP-111 1/4 inch TS to Dual 1/4 inch TSF Y Cable https://www.amazon.com/dp/B000068O53/ref=cm_sw_r_cp_api_gbgZxbZ917924

Then run the tuner out of the volume pedal into one of side of the Y and the out from the delay into the other. The signals should now split at your volume pedal and rejoin after the delay.


Another much easier option is to get an expression pedal if your delay can take one.

So if your guitar amp has a "headphone out" jack, like that's the signal it's actually outputting, you can connect 1 headphone to that...and if you're just using the pedal as a headphone splitter to get two signals out of one, i don't see any issues with that...although, I don't understand why you'd use a pedal and not just use a headphone splitting y-adapter that you could get from a pro-audio section at guitar center or from amazon like this.

> Use an adapter like THIS to duplicate the single mono to dual mono and plug it into both inputs for direct monitoring in both headphone ears.

that's a 2 female to 1 male. Do you mean a 1 female to 2 males?

Skip the mic and get a splitter. Tons cheaper, I suspect it will pick up notes better than a mic anyway.

Hosa YPP-111 1/4 inch TS to Dual 1/4 inch TSF Y Cable https://www.amazon.com/dp/B000068O53/ref=cm_sw_r_cp_api_XWyBybJWFJXHM