Reddit reviews iCreating 10PCS LED 5050 RGB Strip Light Connector 4 Pin Conductor 10 mm Wide Strip to Controller Jumper Solderless Clamp On Pigtail Adapter for 5050 Color Changing Flexible LED Strip light

>It was a bit of a crude process and I wish I had the tools to do it more effectively but basically what I did was take a high density RGB LED light strip and connect it to a four pin strap connector (link below). I then took out the white led and reflector from the inside of the card and replaced the whole reflector with the light strip. Next I took the GTX logo out of the card and sanded off the green outer coat on the lettering and placed it back inside, I put a few pieces of printer paper between the lights and the logo to help with light dissipation and routed the cable out through a small hole next to the IO shield on the front of the card. sorry that this isn't the best step by step guide on how to do it (I honestly got into it without a clue what I was doing) but hopefully this helps just a little bit with your process. Thanks for asking!
>
>https://www.amazon.com/iCreating-Connector-Conductor-Controller-Solderless/dp/B074G48LWQ/ref=sr\_1\_5?keywords=rgb+strip+connector&qid=1550632831&s=gateway&sr=8-5

​

LEDs. Cut them to size, string multiple strands together with some jumpers. I wrapped all my connections with weatherproof electrical tape.

If I'm understanding this correctly, you just need a 4-pin adapter of some sort like this? https://www.amazon.com/gp/aw/d/B074G48LWQ/ref=mp_s_a_1_3?ie=UTF8&qid=1524049728&sr=8-3&pi=AC_SX236_SY340_FMwebp_QL65&keywords=led+4+pin+connectors&dpPl=1&dpID=51g6jpIbo%2BL&ref=plSrch

There are lots of options for this. I personally did my own mod where I used a Corsair Lighting Node Pro and use software to control it: https://www.youtube.com/watch?v=kgMd2CcUkBQ

The 12v Analog RGB strips would be the easiest in terms of controlling as you can buy bulk RGB strips and solder less connectors like these to control your lighting: https://www.amazon.com/iCreating-Connector-Conductor-Controller-Solderless/dp/B074G48LWQ/ref=sr_1_1_sspa?keywords=solderless+rgb+strip&qid=1571675396&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzU1lSR1o3VDk2S0VOJmVuY3J5cHRlZElkPUEwNTEyNzg1M1I1R0NaNVFBUkVRNiZlbmNyeXB0ZWRBZElkPUEwNDI4MDU3Mkg1NE82WjVBM1RUTSZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

The 5v Addressable is a little more work as there are different standards that companies use for connectors. Though if you are comfortable with a solder iron and crimping connectors, then that is an option: https://www.youtube.com/watch?v=6Dl9yd_Nxqk

The phanteks header is the standard 5050 led header it looks like. Pretty sure the LEDs you want have these, but if not....
You'll need something like this

iCreating 10PCS LED 5050 RGB Strip Light Connector 4 Pin Conductor 10 mm Wide Strip to Controller Jumper Solderless Clamp On Pigtail Adapter for 5050 Color Changing Flexible LED Strip light https://www.amazon.com/dp/B074G48LWQ/ref=cm_sw_r_cp_apa_SDtNAbSPZJK9Q

So one thing to note is you should have good plan to solder, unless you plan on using that last link, but those are way too big. These wires are like 26 gauge. Also when you cut silicon it makes it not water proof, so may need some like silicon or something to seal each end.

Could use something like this:
https://www.amazon.com/iCreating-Connector-Conductor-Controller-Solderless/dp/B074G48LWQ/ref=sr_1_4?ie=UTF8&qid=1539742033&sr=8-4&keywords=led+strip+to+wire+connector+3+pin&dpID=51kzc4nBvjL&preST=_SY300_QL70_&dpSrc=srch

or this

https://www.amazon.com/Alightings-Connector-Waterproof-Lights-Connection/dp/B06XHCFMB5/ref=sr_1_3?ie=UTF8&qid=1539742033&sr=8-3&keywords=led+strip+to+wire+connector+3+pin&dpID=511V-NwYvlL&preST=_SY300_QL70_&dpSrc=srch

Just look for 3 pin wire to strip connector or something like that.