Reddit reviews Insteon Ceiling Fan and Light Controller, Fixture Module, 2475F - Works with Alexa & Google Assistant via Insteon Hub

Insteon 6 button Keypad

https://www.amazon.com/INSTEON-2334-232-Keypad-Dimmer-6-Button/dp/B00DN9VGL2/ref=sr_1_1?ie=UTF8&qid=1509735074&sr=8-1&keywords=insteon+6+button+keypad

Insteon Fanlinc

https://www.amazon.com/Insteon-2475F-FanLinc-Dual-Band-Controller/dp/B00715SU4A/ref=sr_1_1?s=hi&ie=UTF8&qid=1509735092&sr=1-1&keywords=insteon+fanlinc

Keypad button labels

https://www.smarthome.com/fanlinc-button-kit-for-keypadlinc-white.html


Boom, done. You don't even need a hub.

came here to say the same thing. I have two of these installed in my house. I did however wire it a little bit different than the way it was stated in the manual. I wired the light directly to the 6 button dimmer and then linked the 4 middle buttons to off/low/med/high with the fanlinc

Fanlinc box wired to the ceiling fan
https://www.amazon.com/Insteon-2475F-FanLinc-Dual-Band-Controller/dp/B00715SU4A

Keypad
https://www.amazon.com/Insteon-Dual-Mesh-Technology-Unbeatable-Reliability/dp/B00DN9VGL2/

keypad insert for the fan speeds
https://www.amazon.com/Insteon-2322-382-FanLinc-Button-KeypadLinc/dp/B007S0CAMQ/




another option i considered but didnt actually pursue is the Aeotec micro dimmer that could be paired with a their wall swipe switch whenever it comes out.
https://aeotec.com/z-wave-wall-switch
https://aeotec.com/z-wave-light-dimmer-switch

It's not a cheap, or easy solution, but here is what I did for my ceiling fan. First off, I am using Insteon smart devices. I don't see a lot of discussion about Insteon here, but I love it. I've pretty much replaced every switch in my house with Insteon. They sell their own smart hub, but I have an ISY994i from Universal Devices because is works with my security system.

So, on the the fan/light control. I bought/installed an Insteon fanlinc. which installs into the housing of the ceiling fan. With the FanLinc and a Smart hub you can control the fan speed and light with program logic, or your cell phone. But to control it from the wall, I installed an Insteon 6 button keypad dimmer and FanLinc button kit. The end result is a smart fan/light I can control with my phone and programming logic, but also has a nice keypad on the wall for setting the fan speed, etc.

Again, this is not a cheap option (especially if you have to buy the smart hub), but it works great!

Personally, I wouldn't recommend a smart IoT ceiling fan. Just in case you switch it out later.
I'll be going with an insteon hub and this, it controls both the light and the fan
Insteon 2475F FanLinc Insteon Dual-Band Ceiling Fan and Light Controller https://www.amazon.com/dp/B00715SU4A/ref=cm_sw_r_cp_apa_vh.ZzbGCPKAXQ

Insteon makes a product for just this. Pair it with a 6 button controller and you’ll have separate control and speeds.

Insteon 2475F FanLinc Insteon Dual-Band Ceiling Fan and Light Controller https://www.amazon.com/dp/B00715SU4A/ref=cm_sw_r_cp_apip_4YQEZhs6N5LUL


Keypad Dimmer Switch (Dual-Band), https://www.amazon.com/dp/B00DN9VGL2/ref=cm_sw_r_cp_api_i_NhaPDbNSKSFH8

There's a z-wave module to control a ceiling fan that doesn't come with a remote, but the Hampton Bay one is cheaper too. I always wanted to pick up the zwave one, but it didn't look like anyone ever tried one with a Wink.

http://www.amazon.com/Insteon-2475F-FanLinc-Dual-Band-Controller/dp/B00715SU4A/ref=sr_1_1?s=hi&ie=UTF8&qid=1463036509&sr=1-1&keywords=insteon+fanlinc

Side note, one of my ceiling fans is the type that has all the buttons on the wall switch. Anyone know if there's a Wink replacement for that?

The best I've come up with for this scenario is to either:

• Like /u/Alwayssunnyinarizona mentioned, expand the gang box so you can add both a Z-Wave dimmer & a Z-Wave fan controller (like the GE 12730) side by side. Since you already have the separate fan and light wiring, this isn't too bad. You would need a drywall saw to expand the hole (or a small saw), [optional] tin snips to cut the old box out, a new 3-gang box and wallplate, and patience.
  
  
• If you have the spare cash, Insteon makes the Fanlinc, which you can hide in the canopy. You could then add an Insteon KeypadLinc. Of course, the gadgets themselves are expensive, and you'd need to add an Insteon modem to your HA setup if you don't already have one. That said, it's as elegant as you'll get without modifying that box.
  
  
• Finally, you could hide a micro dimmer and fan controller in the canopy and use an in-wall scene controller to make your HA hub command them. Not as elegant and more points of failure, but it'll get the job done.