Reddit Reddit reviews iPower GLDUCT4X8C 4 Inch 8 eFet Non-Insulated Flex Air Aluminum Foil Ducting Dryer Vent Hose for HVAC Ventilation with 2 Clamps

We found 14 Reddit comments about iPower GLDUCT4X8C 4 Inch 8 eFet Non-Insulated Flex Air Aluminum Foil Ducting Dryer Vent Hose for HVAC Ventilation with 2 Clamps. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
HVAC
Building Supplies
HVAC Ducting
iPower GLDUCT4X8C 4 Inch 8 eFet Non-Insulated Flex Air Aluminum Foil Ducting Dryer Vent Hose for HVAC Ventilation with 2 Clamps
Ducting size: 4 inches (diameter) x 8 feet (length) when fully extendedThermal endurance: Temperature endurance range from 0 ~ 185°F. (-18℃ ~ 85℃)Wide applications: Kitchens, bathrooms, greenhouses, grow rooms, grow tents, etc.Easy installation: 2 pairs of 4 inch metal clamps made from stainless steel. Flexible length for exhaust fan blower/inline fanFire proof coating: Flexible ventilation ducting made from high-quality flame-retardant aluminum and built-in corrosion-resistant wire helix for reinforcement and lasting performance
Check price on Amazon

14 Reddit comments about iPower GLDUCT4X8C 4 Inch 8 eFet Non-Insulated Flex Air Aluminum Foil Ducting Dryer Vent Hose for HVAC Ventilation with 2 Clamps:

u/ranger737 · 10 pointsr/SpaceBuckets

Sure:

u/living_in_bad_faith · 8 pointsr/Autos

Eh, I'll probably catch flak for this but I hate pie cuts. I think it makes charge piping look like dryer duct, and I'd much rather go polished or powdercoated.

u/MeatyJonesTheRapper · 4 pointsr/SpaceBuckets

Container: Rubbermaid 20 gal Brute Bin

Lights: Kingbrite 60 W Quantum Board (if you want dimmable, ask for a dimmable driver like the HLG-60H-36B and a potentiometer)

Screws: You'll need lots of nuts, long screws, washers, and spacers to mount the board and PSU. First put the board on the lid and mark where to drill, then drill holes. Then put the power supply on the outside in the middle, mark and drill those hoses. Mount power supply and then flip lid over and mount the light, using long screws and nuts to hold it in place (the light should NOT touch the lid but be 1-2 inches from it, held in place by nuts). Drill small hole for power line, then connect. Finally, drill 3 inch hole for exhaust beside the light. You'll also need long screws with nuts to keep the fan and shrouds together. Be sure to use spaces anywhere the screw heads or nuts are touching the lid or the lights. For light spacers, I used rubber spaces between the nuts.

Cooling shrouds: 120mm Fan Duct Cooling Shroud to 4 Inch Vent Hose

90 degree 4 inch elbow for exhaust: 4 in. 90° Round Adjustable Elbow

4" to 3" reducer for exhaust: 4 in. to 3 in. Round Reducer

2x regular JB Weld to mount the reducer and 3 inch "trunk"

Fan: Delta AFB1212SHE-PWM 120mm x 38mm 4pin PWM+Tac Sensor Extreme Hi-speed 3700 RPM 151 CFM

Fan controller: Noctua NA-FC1 4-pin PWM Fan Controller

Fan power supply: LE Power Adapter, UL Listed, 3A, 120V AC to 12V DC Transformer, 36W Power Supply

Fan power supply adapter: CRJ Female DC Power Supply Plug to 12V Molex Power Adapter Cable

Fan molex adapter: Coolerguys Mini 3-4 pin Fan Adapter (Single)

2x ABS fan elbow (for "snout" intake): 3 in. ABS DWV 90-Degree Hub x Hub Long-Turn Elbow

Air filter for intake: 16.25 in. x 12.5 in. x 0.19 in. - 16.3 in. x .2 in. x 12.5 in. - CF300 Carbon Filter

Air filter (not pictured): VIVOSUN 4 Inch Air Carbon Filter Odor Control with Australia Virgin Charcoal for Inline Fan

Fan hose (not pictured): iPower GLDUCT4X8C 4 inch 8 feet Non-Insulated Flex Air Aluminum Foil

Watering device (not pictured): Janolia Automatic Irrigation Kit, Self Watering System, with Electronic Water Timer

Camera (not pictured): Wyze Cam 1080p HD Indoor Wireless Smart Home Camera with Night Vision (glue steel piece for magnetic base onto the upper side of the bin)

Notes: This design is very safe because it keeps all electronic components high in the bin. At the same time, using a battery powered watering system keeps you from requiring to ever open it. The lamp runs very cool. The PWM fan controller works well and keeping the air moving without using a lot of power (do NOT buy a cheap voltage modulator, I did first and it doesn't work nearly as well as the PWM controller). The Wyze cam is super cheap and lets you keep an eye on everything or make timelapses. Have fun growing your tomatoes!

u/andy83991 · 3 pointsr/HerbGrow

Like /u/blackboard mentioned, purchase a carbon filter (4" or 6" depending on size of your setup/plant total) and also get the matching duct (4" duct for 4" filter and vice versa). Also, pick up an inline-fan. A simple and effective way to set it up is to connect fan to the filter, then connect the duct to the fan so it sucks the air through the filter and through the duct, out of the tent. If you have a grow light that is set up to be cooled, just connect the light to be in between the filter and the fan. Make sure you hang or attach the carbon filter higher up in you tent/box, so it removes the hot air. Vent the duct (which is blowing out the warm/stinky air to the outdoors if possible. You can have another inline-fan/duct setup blowing into the tent, but it is not necessary. Just make sure that you have a hole or small opening on the lower, opposite side of your box for fresh air to get sucked in to replace the hot stinky air that your blowing out through the filter/fan/duct.



If that doesn't make sense to you, I can PM you a picture of my current setup.

u/[deleted] · 2 pointsr/microgrowery

Just make sure you have the same size (4 or 6 inch) filter and tubing. I have that fan with this and this and its super simple, everything fits together

u/edbridge · 2 pointsr/Coachella

You can get one of these for the exhaust and turn it to the front of your car.

iPower GLDUCT4X8C 4 inch 8 feet Non-insulated Ducting Aluminum Foil Vent with 2 Clamps https://www.amazon.com/dp/B00EPE3XHY/ref=cm_sw_r_cp_api_i_BOQPCb3A41XHT

u/elninost0rm1 · 2 pointsr/microgrowery

Hi there. I went with that combo because some of the cheaper combos had pretty poor ratings on FakeSpot, but that's really the only reason. If you have a cheaper (and reliable) combo, I'd certainly take a look!

Okay. Do you think I would be sacrificing any "noob-friendliness" by ditching the peat pellets on my first go? I know you can just dump the seed into the medium, but I want to "get it right" my first time and reduce the margin of error. Maybe I'm overthinking it.

EDIT: Would these two work instead of the combo I had?

https://www.amazon.com/dp/B07D8TZ2KV/?coliid=I190I6ZPDD0E93&colid=WARD1BGFR803&psc=0&ref_=lv_ov_lig_dp_it

https://www.amazon.com/dp/B00EPE3XHY/?coliid=I1X2Q9SFFQF5I8&colid=WARD1BGFR803&psc=0&ref_=lv_ov_lig_dp_it

u/Labotomi · 2 pointsr/microgrowery
u/TheObstruction · 1 pointr/PrintedMinis

I also live in an apartment. I've got a Photon, I used my Ender 3 to print this vent adapter and attached 4" dryer duct and an inline fan to it and vented it outside. Luckily my place is kind of dumpy, and I have a piece of plywood in the space that's left from my window AC, since I have sliding windows.

Honestly, the smell of isopropyl tends to be worse.

u/C0smich0rr0r · 1 pointr/PrintedMinis

Set up was super easy, old port screws right off and you screw the new one right one and then slap on a filter and a fan (any carbon filter should do but here’s what I bought that works well)

VIVOSUN 4 Inch Air Carbon Filter... https://www.amazon.com/dp/B01DXYMBU6?ref=ppx_pop_mob_ap_share

VIVOHOME 4 Inch 195 CFM Plastic... https://www.amazon.com/dp/B078HFVTYX?ref=ppx_pop_mob_ap_share

And finally some ducting-

iPower GLDUCT4X8C 4 inch 8 feet Non-Insulated Aluminum Foil Vent with 2 Clamps, Ducting https://www.amazon.com/dp/B00EPE3XHY/ref=cm_sw_r_cp_api_i_CfrZCb6YXV1V7

This really works well for me. The smell otherwise is intolerable. Carbon filters are really amazing.

u/Sofakingcoolstorybro · 1 pointr/microgrowery

This is my idea buy this unit

Black + Decker BPACT10WT Portable Air Conditioner, 10,000 BTU https://www.amazon.com/dp/B01DLPUWG2/ref=cm_sw_r_cp_apa_i_rhgmDbH3D8P2D

Run a duct into my tent from my AC unit
iPower GLDUCT4X8C 4 inch 8 feet Non-Insulated Aluminum Foil Vent with 2 Clamps, Ducting https://www.amazon.com/dp/B00EPE3XHY/ref=cm_sw_r_cp_apa_i_fjgmDbSBGP211

Then eventually connect both into one duct and vent out my window
Ideal-Air 736185 Branch, 4x4x4 Inch https://www.amazon.com/dp/B002JLA4PE/ref=cm_sw_r_cp_apa_i_3jgmDb3R218GH

So something like that? To vent cold air into my tent?

u/skwolf522 · 0 pointsr/HomeImprovement

You should be able to pull that metal part down to get better reach on it.

​

Go to your home improvement store and buy a new hose, you want a more metal looking one.

It should come with 4" hose clamps that screw to tighten them.

​

https://www.amazon.com/iPower-Non-Insulated-Aluminum-Ventilation-included/dp/B00EPE3XHY/ref=sr_1_3?keywords=dryer+hose&qid=1563120074&s=gateway&sr=8-3

​

It is much easier to tighten these hose clamps with a nut driver or nut.