Reddit reviews Krylon K01303007 Acrylic Spray Paint Crystal Clear in 11-Ounce Aerosol

Uh, I just used some acrylic paint my wife had in her craft supplies. Didn't seem like anything fancy. And I did clear coat it!

Edit: The bottles looked like this!

Edit2: Missed the part where you asked about clear coating, but this is what I used to clear coat.

Nail polish won't hold up in the microwave. It pops/explodes.

I found these two sealants options used for diy painted dishes: Mod Podge Dishwasher Safe and Krylon Crystal Clear. They are both supposed to be dishwasher safe, but I don't think they are microwave safe.

Huge improvement! Did you give the whole thing several coats of clear lacquer finish? If not, you should. Make sure you take the panel back off first, of course.

I use this to set my decals

You could probably spray it with fixative.
It'll keep it from yellowing and smudging.
If you don't want the glossy coat, you can just Amazon search fixative.

You can use a clear acrylic spray. I have used such things on top of paint and on bare wood before. They work pretty well. Something like this (although I haven't used this particular one)

https://www.amazon.com/Krylon-K01303007-Acrylic-Crystal-11-Ounce/dp/B00023JE7K/ref=sr_1_2?crid=30K139CPKTBES&keywords=clear+acrylic+spray&qid=1556910026&s=gateway&sprefix=clear+acrylic%2Caps%2C399&sr=8-2

Okay so would this top coat work? or maybe this one An extra question. Would I place stickers before gloss coat or after gloss and before matte?

I would bet you used latex paint. That can interact with the amiibo paint and make it permanently tacky from what I have read.

Use acrylic and something like this to seal it. You could potentially use that spray to get rid of the tacky feeling that's there now. I chose this in Matte rather than gloss.

Best case scenario, use very thin layers, but like three of them. Like dab your paint brush in water first, then layer the paint on.

Which one of these sprays should I get to coat it?

1. 2, or 3?

Would this be an ok gloss coat?
Krylon K01303007 Acrylic Spray Paint Crystal Clear in 11-Ounce Aerosol https://www.amazon.com/dp/B00023JE7K/ref=cm_sw_r_cp_api_LQLdzbNE36NXP

TY for the work and documentation. Not the form factor I was planning on, but might be one I use.

https://www.amazon.com/Krylon-1303-Acrylic-Crystal-11-Ounce/dp/B00023JE7K/ was great to find as your coating, as it's one I own but have, but have never used.

Do you have a link to the linen paper?

Krylon 1311 Matte Finish has been mentioned here before as being a good budget topcoat. I picked up a can at Wal-Mart for $4 but haven't tried it yet.

They also have the [1303 Gloss Finish] (http://www.amazon.com/Krylon-1303-Acrylic-Crystal-11-Ounce/dp/B00023JE7K), I assume it's also as good, maybe? I haven't used either so I could be way wrong.

I've started using spray-on acrylic coating like this on my boxes. It's easier to apply and creates a more even finish than Mod Podge. :)

I used this on my wing SD and it destroyed my acrylic paint. If you spray it on bare plastic I would spray it slowly and it two or three layers.
Too much lacquer paint on PLC plastic can cause warping if your not careful as well.

I use lacquer top coats only after the gloss coat(gloss coat makes panel lining and decal/stickers easily)

I and a lot of others on here use Krylon, https://smile.amazon.com/Krylon-1303-Acrylic-Crystal-11-Ounce/dp/B00023JE7K/ref=sr_1_2?ie=UTF8&qid=1484763744&sr=8-2&keywords=krylon+clear+coat
It much cheaper and more widely available in brick and mortar.