Reddit Reddit reviews kuman DSO 138 DIY Oscilloscope Kit Opening Source 2.4" TFT 1MSPS Digital Oscilloscope Kit with DIY Parts & Probe, Handheld Pocket Sized 13803K, SMD pre-soldered

We found 12 Reddit comments about kuman DSO 138 DIY Oscilloscope Kit Opening Source 2.4" TFT 1MSPS Digital Oscilloscope Kit with DIY Parts & Probe, Handheld Pocket Sized 13803K, SMD pre-soldered. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Lab & Scientific Products
Lab Instruments & Equipment
Lab Meters
kuman DSO 138 DIY Oscilloscope Kit Opening Source 2.4
Dso138 2. 4" Tft 1msps digital oscilloscope kit for DIY it's easy to solder.Oscilloscope functions with no fancy features. Simplicity in structure and easiness in assemblyIt uses 2. 4-Inch tft lcd (320 x 240 dot-matrix, 262K colors) as its display element and displays niceDetailed assembly instructions are provided in combination with troubleshooting guide and schematc.7-24 friendly customer service provided.
Check price on Amazon

12 Reddit comments about kuman DSO 138 DIY Oscilloscope Kit Opening Source 2.4" TFT 1MSPS Digital Oscilloscope Kit with DIY Parts & Probe, Handheld Pocket Sized 13803K, SMD pre-soldered:

u/zachabt · 7 pointsr/ElectricalEngineering

Oscilloscope kits are great. I just did this one a little while back. It was a lot of fun and handy for the price. They sell an acrylic case kit separately too.

kuman 3O-IUX5-O0TZ DSO 138 DIY Kit Open Source 2.4" TFT 1MSPS Digital Oscilloscope Kit with DIY Parts + Probe 13803K, SMD pre-soldered https://www.amazon.com/dp/B0195ZIURK/ref=cm_sw_r_cp_apa_i_LzIQDbP8TT31D

I also got this little signal generator kit to check the O-scope function.

Naravis Gelatinized Black Maca... https://www.amazon.com/dp/B01HM70CMY?ref=ppx_pop_mob_ap_share

u/novel_yet_trivial · 2 pointsr/AskElectronics

Personally I'd start very small, like $50. I just put one of these together and it works well enough for home projects. I would not buy any specialists tool until there is a specific need for it.

u/pokemonfriends · 2 pointsr/synthesizers

It's one of these just sitting on top of the dx7 I think. Cheap as fuck but definitely not pretty. I think its the red pcb clashing with the dx7 pastels that is problematic.

u/robbob2112b · 2 pointsr/AskElectronics

The cheap scope on a chip would work for this.... any number of them on amazon and they are fine for basic stuff with ardino or rpi


https://smile.amazon.com/kuman-3O-IUX5-O0TZ-Digital-Oscilloscope-pre-soldered/dp/B0195ZIURK/ref=sr_1_3?keywords=Oscope+kit&qid=1572835568&sr=8-3

u/Gecko23 · 2 pointsr/3Dprinting

For testing something this simple, you could probably get the answer with something dirt cheap like a DSO138 Kit , $25 unassembled, $30-40 assembled. There's also a 'bigger brother' versions, the DSO202 or DSO221 which are still <$100 assembled.

u/WatermelonMannequin · 2 pointsr/synthesizers

It's not a synth, but this DIY oscilloscope is only $20, and you can order them with the SMD parts presoldered. In case you don't settle on a DIY synth, you can get a prebuilt one and this guy for soldering fun!

u/vitriolix · 1 pointr/synthdiy

Sounds good. I find it amusing that you played it upside down.

Is that scope one of these?

https://www.amazon.com/gp/product/B0195ZIURK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

I am almost done building one with the intention of using it in my eurorack setup. What does the nob do on it?

u/bbartokk · 1 pointr/modular

Is that a decent oscilloscope? Is it this one on Amazon? If so, how do you connect to it?

u/MassDisregard · 1 pointr/ElectricalEngineering

So, for a basic beginning to get into electronics you need:

  1. A soldering iron. For troubleshooting and assembly it is important to know how to solder. There are a bunch of YouTube videos on the subject.

  2. Hookup Wire. 22 AWG solid core is the best wire in my opinion for use in breadboards and general repair.

  3. A Multi-Meter. Probably the most important diagnostic tool you could own. This is not the end all best meter but it is a good DIY soldering experience. You learn some soldering basics while building your own test equipment.

  4. An Oscilloscope. This is a cheap beginner build it yourself scope. This is the second most important tool for a circuit designer to own. This particular kit is good enough for basics.

    This would be a starter kit which would help build up soldering skills and start building up knowledge.

    Getting Started in Electronics is a good read for a beginner to understand basics in circuit theory. I may have seen this floating around the interwebs as a PDF when Radio Shack was going down.

u/mr_william · 1 pointr/modular

Just a cheap diy kit I picked up off amazon. It requires soldering and when I was finished it didn't work. I had to spend about a day googling and scouring through old forum posts to find someone who had a similar issue and see how they fixed it.

Edit it was specifically this one. I got it to teach myself how to solder and even if I fucked it up, I was really only out like 20 bucks.

https://www.amazon.com/dp/B0195ZIURK/ref=cm_sw_r_cp_apa_i_VkuyDb6BQPFJT