Reddit Reddit reviews Litcessory 6-Pin to Cut-End Extension Connector for Philips Hue Lightstrip Plus (2in, 4 Pack, White)

We found 8 Reddit comments about Litcessory 6-Pin to Cut-End Extension Connector for Philips Hue Lightstrip Plus (2in, 4 Pack, White). Here are the top ones, ranked by their Reddit score.

Accessories & Supplies
Electronics
Litcessory 6-Pin to Cut-End Extension Connector for Philips Hue Lightstrip Plus (2in, 4 Pack, White)
✔ ATTENTION -- SELECT THE CORRECT VERSION: Philips makes TWO versions of their lightstrips (Standard 6-Pin V3 and Micro 6-Pin V4). The Micro 6-Pin V4 has a smaller pin connection and IS bluetooth compatible, while the Standard 6-Pin V3 features larger pins and is NOT bluetooth compatible. Please see the image with both connectors to determine the correct version you have before purchasing.✔ ENDLESS DESIGN -- create breaks in your lightstrips, run lights under cabinets, create lighting for shelves, or connect lightstrips across an entire room -- the possibilities are endless!✔ EASY INSTALLATION -- easy to use! Our cables are flat & flexible AND all pin connectors are removable.✔ TECH SPECS -- designed for the Philips Hue Lightstrip system, supports runs up to 33 feet (10 meters), cable is UL listed, made for indoor locations only.✔ REQUIRED -- if you want to connect this product directly to the Philips Lightstrip Plus Controller, you MUST use our Controller to 6-Pin Adapter.✔ LITCESSORY’S HASSLE-FREE 2 YEAR WARRANTY – We know you’ll love this product, but if you have any issues at all, just send us a message and we’ll be happy to assist!
Check price on Amazon

8 Reddit comments about Litcessory 6-Pin to Cut-End Extension Connector for Philips Hue Lightstrip Plus (2in, 4 Pack, White):

u/pwnsauce · 10 pointsr/Hue

Hey everyone, I didn't have the forethought to take photos as I went along, but here's how I did it. Fair warning; this project requires an intermediate amount of soldering experience. If you have surface mount soldering experience, you'll be golden. If you don't, make sure you can handle sacrificing a few light strip segments for this project :)

  1. De-solder the sections of an existing Hue Light Strip. The first half of this video shows how to separate the sections. In the video, he uses a soldering iron. I used a hot air gun to desolder mine; I found the hot air gun approach easier.
  2. Keep careful track of the start and end sections of each strip; you cannot reverse them! Each segment has "PHILIPS" printed on it in blue letters. To help me keep track, I always kept the PHILIPS logo facing upright. At the end of the original light strip, Philips added a female 6-pin connector, so I used female connectors for the end of my segments and male connectors at the beginning. Philips used surface mount contacts with 2mm spacing, which is a lesser-used spacing standard. I bought these for the male end of each segment, and these for the female end.
  3. Break the headers into 6-pin sections. The male ones are easy to break apart with a vice and a pair of pliers. The female headers were a bit more difficult; I held them in a vice and hacksawed them into sections. Then I used a dremel to clean up the messy cut. Someone mentioned using this cut-end to 6-pin product to save on soldering, but I chose to solder each end of the strip. Since the connections will be under some tension when they're bent at 90 degrees, I wanted to make sure they were 100% solid.
  4. Solder the 6-pin connectors to each end of your cut strips. If the female headers were too difficult to break apart or solder, you can technically use male ends on both sides of the strip. Litecessory's cables can be converted to either female-female or male-female.
  5. Spread hot glue over the solder joints to prevent them from making incidental contact with other conductors and to give the connectors more strength.
  6. Use pre-made 2mm 6-pin cables (2 inch, 3 feet) to make your strip as long or as short as you need! When connecting segments, make sure to connect them in the same polarity, such that pins 1-6 on one segment are connected to pins 1-6 on the next segment. If you flip the cable, connecting 1-6 -> 6-1, at best your segment won't light up; at worst it'll fry it for good.
u/Globehopper · 7 pointsr/Hue

Amazon sells connectors from Litcessory that are designed to let you reuse Lightstrip cut-off parts:

https://www.amazon.com/Cut-End-Extension-Connectors-Philips-Lightstrip/dp/B074XLHHB6/ref=sr_1_1?keywords=litcessory&qid=1554685277&s=gateway&sr=8-1

They let you connect the cut-off parts back to the main strip, or to another cut-off. Make sure to watch their instruction video on this page though, as you don't cut where the Lightstrip has the cut marks.

https://litcessory.com/product/cut-end-to-6-pin-extension/

Disclaimer: Haven't actually tried it yet, but I have bought a set of these for a future Lightstrip installation.

u/the_malcontent · 4 pointsr/Hue

Most likely these.

Litecessory makes some good stuff.

u/L300T · 2 pointsr/Hue

Litcessory

Cut-End to 6-Pin 50mm Snap Extension Connectors for Philips Hue Lightstrip Plus

I haven't used this particular connectors, but I have used others from this company.

u/bfodder · 2 pointsr/homeautomation

If you cut on the solder points on the strip (NOT on the dotted line where it says to cut) you can actually solder cat5 cable to both ends as a spacer.

https://www.reddit.com/r/huelights/comments/3pie1d/successfully_split_and_extended_the_hue_light/

If you aren't comfortable with soldering there are these https://www.amazon.com/gp/product/B074XLHHB6/ref=oh_aui_detailpage_o06_s01?ie=UTF8&psc=1

That company sells a bunch of other little accessories that you can use as spacers/extensions or whatever.

Hiding the cable will be hard with your kitchen. Might have to go into the wall and up into the ceiling. Is it an attic above you or a second floor?

That is a cool sink btw.

u/Jamnoggin · 1 pointr/Hue

Thanks for the insight! I'll definitely hold off for a while. I definitely hadn't thought of the corner bend where you can't bend it horizontally. I'm not fussed about cutting them and using these on the corners buf definitely glad you mentioned that.

Cut-End to 6-Pin Extension Connector for Philips Hue Lightstrip Plus (2 inch/50 mm, 4 Pack, White) https://www.amazon.co.uk/dp/B074XLHHB6/ref=cm_sw_r_cp_apa_i_sAUYCbVEZHPW5



I didn't realise the brightness was affected so dramatically if extended so yeah might leave the lightswitch electrics as-is and get two controllers instead and forget the Cat5 link.

  • Would pointing the LED of a spartphone straight down on the kitchen work surface suffice as a test. It's not reflective at all so I think I'll be OK with our cheap plywood worksurface and I can always get a diffuser strip if it bugs me.


    Did you have to create new plug sockets for the lights in your setup?

    The two existing lighting outlets are mounted under the cupboards. That's the bit I know least about - how easy it is to attach a plug socket upside down to a wooden cabinet which has no recess that I'm aware of. I'll have to investigate whether they are on the circuit + switch as I suspect.
u/jubei_700 · 1 pointr/Gledopto

This isn't what you're after, but it shows they do make 6 pin snap connectors.

Cut-End to 6-Pin Snap Extension Connectors for Philips Hue Lightstrip Plus (2 inch/50 mm, 4 Pack, White) https://www.amazon.co.uk/dp/B074XLHHB6/ref=cm_sw_r_cp_apa_i_2GjwCbM9W7N91