Reddit reviews Litcessory Extension Cable for Philips Hue Lightstrip Plus (3.3ft, 1 Pack, White)

We found 3 Reddit comments about Litcessory Extension Cable for Philips Hue Lightstrip Plus (3.3ft, 1 Pack, White). Here are the top ones, ranked by their Reddit score.

✔ ATTENTION -- SELECT THE CORRECT VERSION: Philips makes TWO versions of their lightstrips (Standard 6-Pin V3 and Micro 6-Pin V4). The Micro 6-Pin V4 has a smaller pin connection and IS bluetooth compatible, while the Standard 6-Pin V3 features larger pins and is NOT bluetooth compatible. Please see the image with both connectors to determine the correct version you have before purchasing.✔ ENDLESS DESIGN -- create breaks in your lightstrips, run lights under cabinets, create lighting for shelves, or connect lightstrips across an entire room -- the possibilities are endless!✔ EASY INSTALLATION -- easy to use! Our cables are flat & flexible AND all pin connectors are removable.✔ TECH SPECS -- designed for the Philips Hue Lightstrip system, supports runs up to 33 feet (10 meters), cable is UL listed, made for indoor locations only.✔ REQUIRED -- if you want to connect this product directly to the Philips Lightstrip Plus Controller, you MUST use our Controller to 6-Pin Adapter.✔ LITCESSORY’S HASSLE-FREE 2 YEAR WARRANTY – We know you’ll love this product, but if you have any issues at all, just send us a message and we’ll be happy to assist!

Check price on Amazon

3 Reddit comments about Litcessory Extension Cable for Philips Hue Lightstrip Plus (3.3ft, 1 Pack, White):

u/pwnsauce · 10 pointsr/Hue

Hey everyone, I didn't have the forethought to take photos as I went along, but here's how I did it. Fair warning; this project requires an intermediate amount of soldering experience. If you have surface mount soldering experience, you'll be golden. If you don't, make sure you can handle sacrificing a few light strip segments for this project :)

De-solder the sections of an existing Hue Light Strip. The first half of this video shows how to separate the sections. In the video, he uses a soldering iron. I used a hot air gun to desolder mine; I found the hot air gun approach easier.
Keep careful track of the start and end sections of each strip; you cannot reverse them! Each segment has "PHILIPS" printed on it in blue letters. To help me keep track, I always kept the PHILIPS logo facing upright. At the end of the original light strip, Philips added a female 6-pin connector, so I used female connectors for the end of my segments and male connectors at the beginning. Philips used surface mount contacts with 2mm spacing, which is a lesser-used spacing standard. I bought these for the male end of each segment, and these for the female end.
Break the headers into 6-pin sections. The male ones are easy to break apart with a vice and a pair of pliers. The female headers were a bit more difficult; I held them in a vice and hacksawed them into sections. Then I used a dremel to clean up the messy cut. Someone mentioned using this cut-end to 6-pin product to save on soldering, but I chose to solder each end of the strip. Since the connections will be under some tension when they're bent at 90 degrees, I wanted to make sure they were 100% solid.
Solder the 6-pin connectors to each end of your cut strips. If the female headers were too difficult to break apart or solder, you can technically use male ends on both sides of the strip. Litecessory's cables can be converted to either female-female or male-female.
Spread hot glue over the solder joints to prevent them from making incidental contact with other conductors and to give the connectors more strength.
Use pre-made 2mm 6-pin cables (2 inch, 3 feet) to make your strip as long or as short as you need! When connecting segments, make sure to connect them in the same polarity, such that pins 1-6 on one segment are connected to pins 1-6 on the next segment. If you flip the cable, connecting 1-6 -> 6-1, at best your segment won't light up; at worst it'll fry it for good.

u/anonymous_commentor · 1 pointr/homeautomation

If you want to extend a Hue light strips around something there are extension cables so then you can use only one switch and one controller.
https://smile.amazon.com/gp/product/B01M8Q3T0B/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1

u/danger_moose · 1 pointr/Hue

I soldered mine but had some experience, however afterwards I discovered there are connectors to be found such as

https://www.amazon.com/Extension-Cable-Philips-LightStrip-Plus/dp/B01M8Q3T0B

I'm sure I saw connector to RJ45 on eBay once so you can connect over distance with standard car cable.