Reddit reviews Litcessory Extension Cable for Philips Hue Lightstrip Plus (3.3ft, 2 Pack, White)
We found 7 Reddit comments about Litcessory Extension Cable for Philips Hue Lightstrip Plus (3.3ft, 2 Pack, White). Here are the top ones, ranked by their Reddit score.
✔ ATTENTION -- SELECT THE CORRECT VERSION: Philips makes TWO versions of their lightstrips (Standard 6-Pin V3 and Micro 6-Pin V4). The Micro 6-Pin V4 has a smaller pin connection and IS bluetooth compatible, while the Standard 6-Pin V3 features larger pins and is NOT bluetooth compatible. Please see the image with both connectors to determine the correct version you have before purchasing.✔ ENDLESS DESIGN -- create breaks in your lightstrips, run lights under cabinets, create lighting for shelves, or connect lightstrips across an entire room -- the possibilities are endless!✔ EASY INSTALLATION -- easy to use! Our cables are flat & flexible AND all pin connectors are removable.✔ TECH SPECS -- designed for the Philips Hue Lightstrip system, supports runs up to 33 feet (10 meters), cable is UL listed, made for indoor locations only.✔ REQUIRED -- if you want to connect this product directly to the Philips Lightstrip Plus Controller, you MUST use our Controller to 6-Pin Adapter.✔ LITCESSORY’S HASSLE-FREE 2 YEAR WARRANTY – We know you’ll love this product, but if you have any issues at all, just send us a message and we’ll be happy to assist!
You can do the whole kitchen using one Hue base/power source (you need at least one $90 base in order to control the lights). I used these Litesessory extensions+splitters:
https://www.amazon.com/gp/product/B01M7XDZ5V/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B01N3NTCYU/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
If you need to cut a strip, use these split end connectors as well:
https://www.amazon.com/gp/product/B07NDHP582/ref=ppx_od_dt_b_asin_title_s00?ie=UTF8&psc=1
I had a shelving unit that had built in fluorescent tubes. Now, granted it is an accent shelf, and each shelf was approximately 20" x 18". The fluorescent tubes were on the 20" sides, and there was no lighting on the 18" sides. I used Hue Gen 2 light strips all the way around on all three shelves, and the light (without all the CRI calculations) passed the "wife test". No discernible difference at full power detected. (SCORE!).
I also didn't care for the dots of each LED, so I put the Hue lightstrips into these:
https://www.amazon.com/gp/product/B01NCS0WE8/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
These are super easy to cut with a handsaw, easy to install, and nicely diffuse the LED light and protect the strips.
Where I needed a non-lit extension (such as between each shelf), I used these:
https://www.amazon.com/gp/product/B01M7XDZ5V/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
And finally whenever there was a junction, I used white electrical tape to make sure the two strips stayed affixed. Just a small bit to wrap around the joint.
https://www.amazon.com/gp/product/B000FP8HSM/ref=oh_aui_detailpage_o00_s01?ie=UTF8&psc=1
Assuming that you don't mind them being controlled by a single controller (and therefore the same colour/brightness), I'd buy:
A 2m lightstrip plus for the two cabinets on the right - https://www.amazon.co.uk/dp/B072R5VQJG/ref=sr_1_2?s=lighting&ie=UTF8&qid=1502294468&sr=1-2&keywords=hue+light+strip,
one of these for underneath the microwave oven - https://www.amazon.co.uk/Extension-Cable-Philips-LightStrip-White/dp/B01M7XDZ5V/ref=sr_1_2?ie=UTF8&qid=1502294300&sr=8-2&keywords=hue+light+strip+extension
Which then bridges the gap to another 1m LED strip -(https://www.amazon.co.uk/Philips-Personal-Wireless-Lightstrip-Extension/dp/B0148NMVJW/ref=sr_1_1?ie=UTF8&qid=1502294300&sr=8-1&keywords=hue+light+strip+extension)
Yeah, that might be a better solution.
If the TV and display are close enough, you might get away with 3rd party cable extensions (Litcessory is the only well-known compatible brand) and two 1m extension strips. But they are expensive and will look ghastly if you can't hide them. And you won't be able to control them separately.
The only other method I can think of is using velcro to fix them to the displays and constantly transferring them, which sound crazy.
If the measurements work for you, there are 3rd party extension cables that would let you span the space occupied by the extractor without having cut/splice/solder any strips
https://www.amazon.co.uk/Extension-Cable-Compatible-Philips-LightStrip/dp/B01M7XDZ5V/ref=sr_1_1?ie=UTF8&qid=1488037366&sr=8-1&keywords=Extension+Cable+for+Philips+Hue+LightStrip+Plus+%283ft%2F1m+-+2+Pack%2C+White%29
Best of luck!
These are "UL listed," though I'm not certain that means they are for "in-wall" use:
Extension Cable for Philips Hue LightStrip Plus (3ft/1m, 2 Pack, White)
https://www.amazon.com/dp/B01M7XDZ5V/ref=cm_sw_r_cp_api_LOMozbC5RA5R3
Do the Philips Hue LED strips have the same connector width and pitch? If so something like this would solve my problem:
https://smile.amazon.com/dp/B01M7XDZ5V