Reddit reviews Lixada DC 12V-24V 3 Channel DMX Decorder LED Controller for RGB 5050 3528 LED Strip Light
We found 5 Reddit comments about Lixada DC 12V-24V 3 Channel DMX Decorder LED Controller for RGB 5050 3528 LED Strip Light. Here are the top ones, ranked by their Reddit score.
Receives standard DMX-512 digital control signal and transformrd it into PWM signal to adjust LED.You could connect with DMX digital console to achieve RGB dimming functions.DMX address can be set through dip switch.Two signal interfaces: XLR-3 and RJ45.Up to 15 modes and 31 steps speeds for your options.
It’s being down voted because almost all LED strips require a specific voltage to run on and any AC dimmer will only fuck up your transformer, or (if you plug the strip into the dimmer,) fry the strip.
Its way cheaper to buy a $20 driver:
Lixada DC 12V-24V 3 Channel DMX Decorder LED Controller for RGB 5050 3528 LED Strip Light https://www.amazon.com/dp/B00B42M3RG/ref=cm_sw_r_cp_api_i_.DpGDbCRT3N3G
This is wired... but I've got a couple of these RGB LED DMX controllers I'm planning on playing with. Unfortunately I haven't done anything with them yet.
http://www.amazon.com/dp/B00B42M3RG
Separate three channel controllers is the way to go for a "touring" set. Then you can run DMX and 120V power however is convenient. Or a lot of decoders will have Ethernet ports that do DMX over Ethernet. And Cat5 is cheaper than DMX. You can either build or buy a DMX to Ethernet adapter.
For your power issue, most of those "decoders" come with a 120VAC > 12VDC power supply either built in or as a separate module. Them to the backside where the audience won't see, or even inside of the scenic piece had a frosted front and run your wires through a hole in the back.
I'll pull up a driver/PSU combo in a minute. I don't guarantee the PSU I linked will have the right plug to go into the Decoder, I'm searching fast.
EDIT:
But those 5m 5050 strips only need like 60W of power to run at full intensity, despite the Decoder being rated for more. Again, I'm doing fast math and dredging up old memories of my own projects. Make sure to buy extra of that flat 4 conductor wire to get back to your decoder from the tape.
Soldering that stuff sucks, I recommend getting some liquid E-tape to seal things up since you're putting four solder connections next to each other in like 1/2 an inch.
Decoder: Lixada DC 12V-24V 3 Channel DMX Decorder LED Controller for RGB 5050 3528 LED Strip Light https://www.amazon.com/dp/B00B42M3RG/ref=cm_sw_r_cp_apa_0UhLBbZ3NVFRP
PSU: LEDwholesalers 12V 20A 240W AC/DC Power Adapter with 5.5x2.5mm DC Plug and 2.1mm Adapter, Black, 3262-12V https://www.amazon.com/dp/B074GGMD5J/ref=cm_sw_r_cp_apa_CYhLBb662YCTC
Edit_2:
You definitely don't want to try putting power down pins 4 and 5. DMX cable isn't made for it, it will end in cooked cables, which can be a fire hazard.
Also, you didn't say what these boxes are doing, are they scenic elements?
Also the LED strips can be put on DMX and used as a light during some of the songs. It is really simple and cheap to do http://www.amazon.com/TOMTOP-12V-24V-Channel-Decorder-Controller/dp/B00B42M3RG/ref=sr_1_1?ie=UTF8&qid=1405728815&sr=8-1&keywords=led+strip+dmx
I'm assuming you're using the cheap LED tape? For that I just buy 'em. Set the dips to the address and it's just plug and play from there. If it's just RGB tape then you only need 1x 3 channel per strip.
There's nicer models out there, most come with the transformer. City Theatrical makes some nice pro-quality ones if you're needing an excuse to spend a lot of money.