Reddit Reddit reviews Metra 70-1761 Radio Wiring Harness For Toyota 87-Up Power 4 Speaker

We found 18 Reddit comments about Metra 70-1761 Radio Wiring Harness For Toyota 87-Up Power 4 Speaker. Here are the top ones, ranked by their Reddit score.

Electronics
Car Audio & Video Wiring Harnesses
Car Electronics Accessories
Car Audio & Video Installation Products
Car & Vehicle Electronics
Metra 70-1761 Radio Wiring Harness For Toyota 87-Up Power 4 Speaker
For select 1987-2007 Toyota and Scion vehiclesPlugs into car harness at radioPower/4 SpeakerOne 10-pin plug and one 6-pin plugAllows for the installation of an aftermarket radio using the existing factory wiring and connectors
Check price on Amazon

18 Reddit comments about Metra 70-1761 Radio Wiring Harness For Toyota 87-Up Power 4 Speaker:

u/AKADriver · 4 pointsr/cars

You probably should have considered this before buying the stereo.

The nice thing is, a '98 Corolla is one of the easier installs. It has a standard "single-DIN" (2" x 7") radio, and any aftermarket head unit will have existing holes on the sides of the deck to screw directly onto Toyota radio brackets.

If the new stereo you bought is "double-DIN" (i.e. about 4" tall instead of about 2" tall) it will not easily fit in your car. Sell or return it and get a single-DIN.

If you bought the stereo from a major stereo retailer like Crutchfield they would have included instructions and a jumper wiring harness that would have made this a no-brainer. If you don't have a jumper wiring harness you'll have to make one. The stereo comes with its male side of the harness; you'll need the correct female plug for your car to complete it. To put the two together, solder or butt-splice the matching wire colors. Do not attempt to cut and splice the car's own wires! For a normal stereo install there is no need.

u/cvr24 · 4 pointsr/CarAV

I have a 2009 Vibe, which is virtually the same as your Matrix. Apply e-brake, shift into N, then pull up on the dash bezel from the bottom, just below the hvac controls, to remove. Get the Scosche dash kit https://www.scosche.com/2009-toyota-matrix-pontiac-vibe and any double-DIN fits in there just fine. When screwing the radio in, push up on the radio and alignment will be better. You'll need a standard Toyota wiring harness to splice into the harness that comes with your new radio, then it's plug and play. If you have steering wheel controls, you'll also need a steering wheel interface.
Order everything from Crutchfield and they will include all those extra parts with your order. Here's a pic of my install: http://forums.genvibe.com/phpBB3/viewtopic.php?f=30&t=45247#p513922

u/chll3r · 3 pointsr/CarAV

Kenwood KMM-BT315U.

Its a media receiver meaning it doesn't play CD's.
Amazon right now for $77.


Wiring Harness Metra 70-1761 $5


Dash Kit Scosche $12

$94 before taxes.

Watch This; if you're not comfortable doing that please get it professionally installed (shop around, $80 max for labor on an install like this).

You can find Pioneer BT receivers for less also, I just like the way Kenwood looks.

The dash kit I listed will only fit a single din radio, for double din you'll need the metra kit.

u/swordstool · 2 pointsr/prius

I don't have a V, rather a Gen3 2013. I had a JVC KWAV61BT put in. Purchased on Amazon for $200 a year ago. Also got from Amazon: Steering Wheel Control Wire, Dash Kit, and Wiring Harness. Had a local shop install it for $100. I probably could have done it myself, but wanted it to look professional. Total cost of the stereo and parts was $275. Looks like Amazon has the DDX-372 for under $300.

u/Theguywithouttheface · 2 pointsr/NoStupidQuestions

It depends on the car. Most cars made before 2015 or so use a standard Double Din Slot radio (With Double Din being the size of the radio) while cars older than 2000's might have a single din slot radio. All of these radio's are interchangeable and can be swapped out (Sometimes with an adapter kit). The slightly trickier part if you want to do this yourself is wiring up a harness that connects your cars electrical system (speakers/power/USB/FM radio) to the radio you want to install. You will need to find an electrical manual or a guide online to tell you which wires are for what and connect them to the corresponding wire on the new radio.

Source: Replaced the shitty radio in my old Subaru

u/SherlockCmbs · 2 pointsr/ft86

For general functionality of the head unit you just need Metra 70-1761 Radio Wiring... https://www.amazon.com/dp/B0002BEQJ8?ref=ppx_pop_mob_ap_share this is what i use in my 2014 brz and the metra usb adapter. I had the pac from a prewired harness from crutchfield but it was annoying.

u/iPhantasy · 2 pointsr/ft86

There are 3 different connectors that you'll have to hook up to the connector that comes with the head unit that plugs into the head unit itself. The other 3 connectors are VERY easy to install. 0 electrical engineering education, but common sense and the color coded instructions on the back of the packaging explains all you need to know.

Radio Antenna harness

Main connection (two main connectors that came out of the factory head unit)

USB Connector (if your car came with usb at the bottom right of the center console)

Should mention that the stock AUX connection won't function. You will have to run an extension from the back of the head unit to somewhere in your car. I routed mine to the left side of the passenger seat held up by this thing.


I don't use the microphone for bluetooth so that's not connected. I don't plan on using my head unit for displaying for any video sources so I didn't bother hooking up the hand brake bypass. The GPS antenna I just stuck to some metal plate that was inside the head unit cavity (pretty strong magnet and pretty accurate).

You may want to pick up a bracket like this. to fill in the rest of the head unit cavity along the sides. I'm not too sure if this is the exact one for the head unit. Crutchfield automatically told me what parts I would need to completely setup the head unit including the bracket and connectors. I couldn't find yours on the site so I can't tell you exactly which bracket to get. They're both Pioneer head units so it's worth a try. The bracket is a generic bracket made for most Toyota cavities to support double DIN sized head units. I had to do some slight Dremel work to get everything to line up with the stock mounting bracket. A solid afternoon with everything and I was set by the end of the day.

I had to contact OEM Audio Plus about how to get power to their amplifier because they have a replacement harness for the stock harness. But that's information that doesn't pertain to you unless you own their system with a subwoofer.

Tl;dr: Links 1-3 are what you need to connect everything. Link 4 is some random accessory I bought that happened to work things out. Link 5 is a bracket adapter to the stock bracket. Last link is the site that showed me all the stuff I needed and I just looked them all up on Amazon.

u/Bwdzxc · 2 pointsr/CarAV

Alright so what you do, is buy [this.] (http://www.amazon.com/Metra-70-1761-Wiring-Harness-Speaker/dp/B0002BEQJ8) What this allows you do to is connect your aftermarket headunit to the factory system without damaging factory wiring. It will connect to your aftermarket radio harness via soldering (perfer) or butt connectors then will just plug right into factory plug. You will have some wires left over on the Metra harness like remote turn on, unless you have a aftermarket amp, the power atenna wire, and sometimes the dimmer wire. So don't worry about that.

u/TheRawCarnage · 1 pointr/WRX

https://www.amazon.com/gp/product/B07GD8627K/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 this is the harness i used, has the reverse 6v signal already to go. all you need us usb retention https://www.amazon.com/gp/product/B01DJ4KVQ6/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

then the speaker harness. https://www.amazon.com/gp/product/B0002BEQJ8/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

and lastly the antenna harness https://www.amazon.com/gp/product/B003VYWSES/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

these were all the things i used to wire in my kenwood. besides the tool to keep steering wheel buttons https://www.amazon.com/gp/product/B00J4W10XG/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

the autoharnesshouse harness makes it easy to use the maestro by the way. hope this helped. i have a 2017 wrx by the way so i dont know if there is a difference with 2015 and the new 2018+s

u/LowBatteryLife · 1 pointr/ft86

Do yourself a favor and get a reverse harness set from something like Metra. It'll break out the connections into bare wires in fairly standard color coding. Yellow is hot +12V, Red is switched +12V, Black is Ground, Blue is amp +12V, etc.

Metra Harness Set

Antenna Adapter

u/narib687 · 1 pointr/DIY

yea maybe.... Next time buy the wire harness for your car...They are like 3 bucks

Example

u/Herrowgayboi · 1 pointr/4Runner

I don't have RDS, but I do have the JBL Synthesis system, that looks like this.

That said, I have some confusion with the wiring harness...

  1. Do I NEED to pick up a JBL wiring harness just so that I can use the factory amp/sub?
  2. Can I use the regular wiring harness like this one, or will I need to pick up another one?


    Thanks

u/AOLFreeTrial · 1 pointr/ft86

If you want it to be easy as possible, you can use one of these (and you'll need to pick up a maestro sw or rr):

https://www.amazon.com/AutoHarnessHouse-Aftermarket-Installation-compatible-2016-2019/dp/B07GD8627K/ref=sr_1_1?keywords=autoharnesshouse+brz&qid=1573219865&sr=8-1

​

That covers the steering wheel controls and camera, antenna amp, and factory amp. You'll need to add a pin and wire on the harness (it's included) to power up the factory amp and door speakers. Also, ignore the instructions included on the two 5-pin connectors - just connect the two on the harness together if it's not shipped as such. If you want to try to keep costs down and make your own, you'll need to wire in a voltage converter for the camera power feed.

You'll also need the standard Toyota harness for the rest of the speakers. You can use one of AutoHarnessHouse direct connect Pioneer ones, or just make your own a little cheaper. I believe this is the part, but please double check - I don't have the part number handy right now (You can actually get these at Best Buy, it's in their computer system):
https://www.amazon.com/Metra-70-1761-Wiring-Harness-Speaker/dp/B0002BEQJ8/ref=sr_1_1?crid=344R0OVLJ7ACT&keywords=metra+toyota+harness&qid=1573220037&sprefix=metra+toyo%2Caps%2C155&sr=8-1

​

For the 4500, I also recommend either wiring up their GPS antenna, or just using an adapter for the OEM one (I went this route just to keep things clean). This pack contains the correct adapter (it's the one with the bright green end, maybe you can find it standalone cheaper):

https://www.amazon.com/gp/product/B01K03PORU/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

​

If you don't hook up the GPS antenna, the head unit will throw up an error message every time you start up a navigation app in AndroidAuto (it'll still work, it's just annoying).

Lastly, don't forget an antenna adapter and (optionally the OEM USB port adapter cable). I opted not to use the USB port since I have a high speed charger that uses a 12v socket. Same as above, please double check this to make sure it is the right one, but here's what the antenna adapter looks like:

https://www.amazon.com/Metra-40-LX11-Antenna-Adaptor-Select/dp/B00JYHSDKO/ref=sxbs_sxwds-stvp?keywords=toyota+antenna+adapter&pd_rd_i=B00JYHSDKO&pd_rd_r=aae8b955-0220-497c-bcd6-480183748bd8&pd_rd_w=bmQ4P&pd_rd_wg=7ZU9O&pf_rd_p=a6d018ad-f20b-46c9-8920-433972c7d9b7&pf_rd_r=F20PSH58JCQN60PP1T5G&qid=1573220626

You'll need to wire in the blue wire to power the antenna amp. Don't hook it up to a constant 12v feed (yello), either use a switched feed, or wire it to the matching blue feed on the back of the harness (it's the one that feeds out of the two pins jumped together by a blue wire).

​

Sorry I can't be 100% on the last couple of adapters - if you have trouble confirming feel free to DM me and I will be happy to check when I get home from work, I kept the packaging for later reference, and again, Best Buy does have these in their computer, so even if your local one doesn't carry them, they should at least be able to give you the part number.

u/MagicJello · 1 pointr/CarAV

House?

Car- 2017 Toyota 86

HU - https://www.pioneer.com.au/shop/car/avh-zl5150bt/

Harness- Metra 70-1761 Radio Wiring... https://www.amazon.com/dp/B0002BEQJ8?ref=yo_pop_ma_swf

u/Herp_in_my_Derp · 1 pointr/CarAV
u/FlawedButFly · 1 pointr/CarAV

OK. So here is where I am. I have decided to first work on installing an aftermarket DOUBLE-DIN head unit with Bluetooth wireless speakerphone, Aux-in, etc. (and I will do the amp + subwoofer in the next phase).

So far I've purchased:

  1. Dash Kit which is apparently appropriate for my 1999 Lexus LS400: Scosche LS2085B
  2. Wire Harness Kit which someone on Amazon reported worked flawlessly for an aftermarket stereo in their 1998 Lexus LS400: [Metra 70-1761 Radio Wiring Harness] (http://www.amazon.com/Metra-70-1761-Wiring-Harness-Speaker/dp/B0002BEQJ8/ref=cm_srch_res_rtr_3)

    Now (I believe) the only thing left for me to purchase is a double-din aftermarket head unit. Do you happen to know of any that would be compatible with this setup? Or am I pretty much able to use any head unit I want because I've installed a dash kit?

    Thank you so, so, so much. I can't tell you how much your help means.
u/Itsfreezing · 1 pointr/prius

http://priuschat.com/threads/stealth-install-an-aftermarket-stereo-in-prius.38700/

This provides all the info needed for the most part. I ordered the stereo from Crutchfield and it came with the OEM to aftermarket wiring harness needed, but I also needed to buy an additional harness to avoid the dreaded red triangle resulting from some installs. There is a way to fix this with a resistor but the harness seems to be more reliable.

Stereo: JVC KD-R950BT

Wiring Harnesses: Metra 70-1761:
http://www.amazon.com/Metra-70-1761-Wiring-Harness-Speaker/dp/B0002BEQJ8/ref=sr_1_1?ie=UTF8&qid=1398123517&sr=8-1&keywords=Metra+70-1761

Best Kits BHO1761 OEM Radio Wire Harness:
http://www.amazon.com/dp/B0088TNGRE/ref=pe_385040_30332190_TE_3p_M3T1_ST1_dp_1

u/fltsht · 1 pointr/cars

I installed this in my 01 Corolla a couple weeks ago. It fits in the stock mounting bracket and has AUX, BT and USB. All you will need to install it is this wiring harness, a set of crimp caps and a wire stripper/crimp tool.

The hardest part is wiring the new head unit to the wiring harness. The actual installation should take 10 minutes.