Reddit reviews MOOG Chassis Products ES2079S Tie Rod End Adjusting Sleeve
We found 6 Reddit comments about MOOG Chassis Products ES2079S Tie Rod End Adjusting Sleeve. Here are the top ones, ranked by their Reddit score.
Coated for corrosion resistanceAlloy steel construction provides durabilityIncludes any necessary hardwareFits select 1980 - 1996 Ford and Jeep vehiclesAdjustableEasy to installMade of durable, all metal constructionAll parts meet or exceed OEM (original equipment manufacturers) standards
Start of a long line of new parts for the 2000 XJ:
Finally got the ball joints out yesterday around 1pm.
Had to go get an impact gun to even touch the axle nut. Then the damn 13mm 12 point bolts that hold the hub in. Some how I did not strip a single one but have no faith in putting them back in, so now waiting for new bolts to be delivered. Every single cotter pin on the ball joints were so rusted and pushed into the castle nut that I couldn't get them out, so go get new impact sockets (and another trip for swivel sockets for the upper) and unleash all hell to shear the cotter pins off.
Finally got to pushing the ball joints out and the OTC set receiving cup is a touch to big for the lower ball joint, so off to Harbor Freight to get an adapter set.
Anyways, half a rant but happy to hopefully have a Jeep that wont wobble down the road.
Just did mine over the weekend! Amazing upgrade for so little money and effort. This really should have been OEM on the TJ. Hardest part of the job was pulling out the cotter pin on the wheel side!
For anyone that wants to do this upgrade:
Moog DS1312 Tie Rod End
Moog ES3096L Tie Rod End
Moog ES2079S Tie Rod End Adjusting Sleeve
Get yourself some rustoleum (I went with flat black enamel) and put a few coats on it. While installing, know that the little end is reverse threaded.
sorry links are in .ca because that's where I ordered them, but you'll have the right part number.
sleeve : https://www.amazon.ca/Moog-ES2079S-Steering-Center-Link/dp/B000C57VBY
tie rod end (long) : https://www.amazon.ca/Moog-DS1312-Steering-Center-Link/dp/B000C5400E
tie rod end (small) : https://www.amazon.ca/Moog-ES3096L-Tie-Rod-End/dp/B000C59W7U/ref=sr_1_1?ie=UTF8&qid=1465312612&sr=8-1&keywords=ES3096
here's the thickness difference between both to give you an idea: http://www.stu-offroad.com/steering/zjtie/tie-1.jpg
Here's a list of the parts you'll need /u/RebornSpartan . I did pretty much the same thing last year.
Also, if you replace one wheel bearing I'd suggest knocking out the other one while you're at it. That also gives you the chance to check the axle shaft u-joints while you're at it.
2x Timken HA597449 Axle Bearing and Hub Assembly - $150
You will also need a 36mm socket specific for the nut on the axle shaft. I bought this one from Amazon when I ordered the wheel bearings: TEKTON 4936 1/2-Inch Drive by 36 mm Deep Impact Socket, 6-Point - $14.
Something to be aware of (paranoia at its finest) is the possibility that your hub bolts may be rusted all to hell and need replaced. Or in case you want to replace them "just because". You can get them from Quadratec @ $4/ea and you will need a total of 3 for each side. Crown Automotive 34201535 Front Knuckle To Hub Bolt
Here are the Moog part #s for the ZJ tie rod upgrade:
1x Moog DS1312 ZJ Tie Rod End - $54
1x Moog ES3096L XJ/ZJ Tie Rod End - $26
You can generally re-use the adjusting sleeve that's already on the components you're going to replace, but in case you want/need a new adjusting sleeve it's only an additional $15.
1x Moog ES2079S XJ/ZJ Tie Rod End Adjusting Sleeve - $15
While you're down there mucking about with the steering, you should check the drag link and the track bar as well.
If you need/want to replace the drag link assembly, here are the part #s you'll need. Again, you can generally get away with re-using the adjusting sleeve so that will save you $15 if you do.
1x Moog DS1238 Tie Rod End aka Drag Link - $60
1x Moog ES3096L XJ/ZJ Tie Rod End - $26
1x Moog ES2079S XJ/ZJ Tie Rod End Adjusting Sleeve - $15
For the track bar:
1x Moog DS1235 XJ Track Bar - $59
Now, on to the sway bar links. If the links themselves are still good, all you need to do is replace the bushings.
2x Moog K3150 Sway Bar Link Repair Kit - $17
If your links are crap (usually the top bolt is rusted all to hell, or people don't want to screw with pressing out the old bushings) you can get two of these kits to just do a straight replacement.
2x Moog K3174 Stabilizer Bar Link Kit - $38
And don't forget to replace the mounting bushings for the sway bar while you're at it, also.
1x Moog K3171 Sway Bar Bushing Kit - $10
If you are looking to replace the drag link, I would highly suggest upgrading everything down there to the V8 Grand Cherokee set. It is a solid setup, whereas the TJ's are just tubes. Here are the following amazon links to completely replace them:
Moog ES2079S Tie Rod End Adjusting Sleeve
Moog ES3096L Tie Rod End
Moog DS1312 Tie Rod End
Moog DS1310 Tie Rod End
It may seem like a bit of money at the moment, but these parts are actually cheaper than buying the TJ version of the same parts! The V8 is not in high demand, and as such the prices are lower compared to the much more popular TJ parts.
> Turned out the drag link clamp was turning despite the nuts not being loose
Replace it if needed