Reddit Reddit reviews RCBS Heavy Duty Plastic 87076 Rotary Case/Media Separator Essential Tool

We found 8 Reddit comments about RCBS Heavy Duty Plastic 87076 Rotary Case/Media Separator Essential Tool. Here are the top ones, ranked by their Reddit score.

Sports & Outdoors
Gunsmithing Tools
Hunting & Fishing
Gun Maintenance
Sports & Fitness
Shooting
Gun Accessories, Maintenance & Storage
RCBS Heavy Duty Plastic 87076 Rotary Case/Media Separator Essential Tool
Made of the highest quality materialsHunting reloading case cleanersAnother quality Bushnell productSeparates the cleaned cases from the cleaning mediaHeavy-duty plastic construction for years of trouble-free serviceCapacity: appprox 180 .30-06 cases or 400 .38 Special cases with media
Check price on Amazon

8 Reddit comments about RCBS Heavy Duty Plastic 87076 Rotary Case/Media Separator Essential Tool:

u/WildBTK · 3 pointsr/reloading

Here's how I handle it:

  1. Get a media separator (example).
  2. Dump contents of tumbler into this separator, spin it 30-40 times.
  3. At this point, virtually all of the pins in the brass have fallen into the water, but the brass is in the separator.
  4. Dump brass into a large food strainer (dedicated for this purpose, not for food straining afterwards!) in a sink and wash and dry brass as normal.
  5. With the water and pins still in the base of the separator, use a 5-gallon paint strainer bag to reclaim the pins. (example). Pins will be in the strainer. You can wash the residual soap from the pins while in the strainer.
  6. Profit!
u/tank-industries · 2 pointsr/reloading

I use the RCBS media separartor. I fill the bottom half with water and turn it for a couple minutes. Then the brass goes into a bath towel and I gran the corners and roll the brass around in there for a couple minutes. Then they go in the oven for about 20 mins. That seems to get all the pins out for me.

u/uid_0 · 2 pointsr/reloading

I bought a $30 RCBS media separator and have no regrets. Dump everything in there and 30 seconds later the job is done.

u/DragonCenturion · 1 pointr/reloading

For separating I used to use the RCBS Media Separator, it worked ok, but was just a lot of work.
I am now using a set of gold sifting pans, 1/4 and 1/100, and it works great.

And as for the HF tumbler, I recommend Modding the Drum.

u/ickyfehmleh · 1 pointr/reloading

The RCBS-style media separators, with a closing lid, are ideal for this. As an added bonus you don't have media flying everywhere.

u/Notorious_Dave · 1 pointr/reloading

This is my current plan, tell me what you think I should do different.

Press

Bullet puller

Scale

Dies

Caliper

Book

Tumbler

Media

Media Seperator


Case Prep Tool

Trimmer And also the needed shell holder

u/Barry_McKackiner · 1 pointr/reloading

I have the same wet tumbler you do. I use this media separator to spin around the cases to remove any pins I missed from shaking out the tumbler into a big bucket. Works very well. I fill it with water and do one run through water and then another run in open air.

Also, GET THE MAGNET those little bastard pins get everywhere and your life will be 100 times easier with the magnet to pick them up quickly.

As for drying them after, I got THIS food dehydrator. works like a charm. It's got a good price point and it has temp and timer controls so you can set it and forget it. I usually run it for 1.5 hours at 130 degrees to dry out my brass. I'd also recommend additional mesh nets as smaller cases like 9mm want to fall through the outer spokes. The nets prevent this and also let you put more on there completely horizontal to get any remaining water to drip out.

u/desktop_version_bot · 1 pointr/reloading

Here is the desktop version of your link