Reddit Reddit reviews Sapphire Collection 18 cm Non Stick Sauce pan and Glass lid, 18cm, Black

We found 1 Reddit comments about Sapphire Collection 18 cm Non Stick Sauce pan and Glass lid, 18cm, Black. Here are the top ones, ranked by their Reddit score.

Kitchen & Dining
Kitchen Cookware
Saucepans
Home & Kitchen
Pots & Pans
Sapphire Collection 18 cm Non Stick Sauce pan and Glass lid, 18cm, Black
Great value for moneyEasy to useEasy cleanLight wieghtDish washer safe
Check price on Amazon

1 Reddit comment about Sapphire Collection 18 cm Non Stick Sauce pan and Glass lid, 18cm, Black:

u/Poohh_Bear · 3 pointsr/ECR_UK

What I personally recommend is buying CBD Isolate and making the juice yourself. That's what I am doing for my lower back and neck pain.


I bought the Isolate with GSC terpenes which gave it a nice earthy flavour, though I can't say if added anything for pain relieve.


If you want to know how to make it here goes...

Ingredients:

  • Propylene glycol (e-liquid base)
  • Isolate (contains CBD)
  • Tap water (for heating)

    Equipment:

  • Dropper bottle of choice (storing liquid)
  • Sauce pan (holding water and bottle for dissolving isolate)
  • Scales (used for weighing PG and Isolate)
  • Pipette (getting the PG into the bottle)

    (Links are just there to show what I used)

    NOTES: The isolate is not water soluble so using VG isn't recommended as the dissolved isolate can crystallise in the liquid due to the water content in the VG; PG doesn't have this issue. PG however, is know to give a throat hit, but from my usage I haven't found this to be an issue.

    To work out the the amount of PG and CBD first deiced how much CBD per ml you would like. I wanted around 15mg per ml which I would say is good for me. The recommended strength seems to be around 13.5 – 20mg/mL. Then you just multiple the CBD/ml by the amount of liquid you want to make. So for 15mg/ml @ 30ml you would do 15×30 to get 450mg of isolate.

    DON'T use an amber bottle if possible - it's a pain to see the isolate when water is on the bottle as it goes very dark.

    Instructions:

  1. Prepare the solution
    1. Weigh out PG (1.04g = 1g) using pipette straight into the bottle.
    2. Weigh out the Isolate and put into the PG.

      I did this on some foil that was folded into a cross so I could poor the isolate directly into the bottle. You could also use I funnel, but i only had large ones to hand that wouldn't fit the neck of the bottle.
  2. Get some water in the pan and bring it to a simmer but not to hot (just enough so you can just hold your finger in the water). Ideally it should cover the level of liquid in the bottle, but not submerge the whole bottle.
  3. When the water is simmering turn the heat of and place the bottle in the water. I left it for 10 minutes and then shook the bottle to help break the big bits down (not as necessary for isolate without turpentines.
  4. After 10 minutes, the water had cooled slightly, so I put the hit back on until it was back to a simmer. I then left it for another 10 minutes. This process should be repeated until all the Isolate has visible dissolved. I think it took me 3 or 4 for it to fully dissolve.

    Vaping

    I would recommend a RTA or RDTA since the liquid can gunk up the coils at a reasonable rate, so making you own is ideal to get around this. I am vaping on the following coils:

  • 24AWG Kanthal A1, 11 wraps, 3.0mm (ID) Single coil @ 1.00-ohm 35W.

    I vape this 2-3 times a day depending on the pain, and it works a treat.



    If you have any questions feel free to ask :)