Reddit reviews Self Drilling Drywall Plastic Anchors with Screws Kit
We found 12 Reddit comments about Self Drilling Drywall Plastic Anchors with Screws Kit. Here are the top ones, ranked by their Reddit score.
Starts easier than other self-drilling drywall anchorsDeep thread design provides strong engagement in 3/8", 1/2" or 5/8" gypsum wallboardPre-drills precise hole in gypsum wall board - No hole preparation requiredConstructed from durable plastic to last for years. Can be easily removedKit Includes 20 Plastic Anchors, 20 #8 x 1-1/4'' Phillips Screws and a Plastic Case, Hangs up to 50 lbs
Don’t listen everyone freaking out about finding studs. If you have actual drywall and not plaster, then anchors are perfectly fine. I’ve had a 42” tv mounted to drywall for 8 years using 6 of these anchors because I’m German, and I like engineering overkill. Each one holds 50 lbs.
get the screw in type or toggle anchors and they will be plenty strong. people hang TV's using these, even without studs.
if you can get one stud, they should provide enough resistance against the "pull out of the wall" force, even if the other side is only held in by drywall anchors.
Depending on how much weight you're talking about hanging it's usually best if you can find a stud to directly screw into.
In absence of that being an option, self drilling drywall anchors are the next best option. You could use something like THESE to go directly to where the old smaller anchors it appears you have were at.
I make and install curtains for a living, this is my time to shine!
First things first, other posters are correct that you’re going to need to patch the drywall and use drywall anchors for your next attempt. Do not use any of the screws or anchors included with the curtain rod, you need to get the right hardware for your wall which probably means longer screws as well as better anchors. These are the kind of drywall anchors we use.
I assume you’ve got premade curtains, which comes in standard lengths. The previous tenants probably did the same, so it’s very likely that all the drywall in that specific rod height is majorly compromised. Is there any way you can hang your rod higher or lower and hem your curtains? Anchoring your rod into undamaged drywall (or even better, try to find the studs or header on either side and top of the window) and attach your brackets into that.
Lastly, do you have enough brackets holding up your curtain rod? We always include a center support bracket if the rod is wider than 60 inches. This helps distribute the weight better and keeps your curtain rod from sagging.
Hope this helps! I could give you a few more tips, but I’d need to see the kind of curtain hardware you’re using and the window you’re trying to hang it onto.
If I were you I'd go with something like this:
https://www.amazon.com/dp/B07GYRQVJF/ref=cm_sw_r_cp_awdb_t1_uBS2Db90R31CG
As there isn't studs, anything that protrudes from the wall is applying alot of pulling force to any of the top screws. The wider mount keeps it close to the wall and gives you a much larger surface area to mount the hell out of the tv.
Id also use something like these:
https://www.amazon.com/Drilling-Drywall-Plastic-Anchors-Screws/dp/B01FCZ8I3I/ref=mp_s_a_1_4?keywords=drywall+anchors&qid=1574619039&sprefix=Drywall+an&sr=8-4
These are to give a bit more reliant hold to the drywall, not fantastic, but with enough of these (like 8-10 of them) with a static tv mount, you should be fine.
This all does depend on the weight of the tv and any angle you have the TV mounted at though.
I've used these to replace plastic anchors holding a couple of towl racks to the wall. they have a larger diameter than the plastic anchor hole and so far have held up well.
Those are garbage. Throw them away. Get something like these instead.
https://www.amazon.com/dp/B01FCZ8I3I/ref=cm_sw_r_cp_awdb_t1_inmwCbW1JC7Z6
Maybe you've already thought of this, but it's possible you're hitting a screw or nail. I know you said the stud finder doesnt say metal is there.
Do you face the same issue if you move the installation up/down 3 inches? Are your curtains light enough to use these drywall screws?
(not moly screws.... Dont ever use molly screws).
Edit: still trying to figure out formatting in Reddit
Just go directly into the sheetrock and I like to use the "screwable" anchors like these:
https://www.amazon.com/Drilling-Drywall-Plastic-Anchors-Screws/dp/B01FCZ8I3I/ref=zg_bs_6906598011_3?_encoding=UTF8&psc=1&refRID=XG17A75N5E2MX0RSWBGE
They're super easy to install and no need to drill.
They aren't drilled into a beam, I used anchors with the hooks. They're great and will ensure the hook wont go anywhere!
These work great and are easy to use, just screw in the anchor then the provided screw
https://www.amazon.com/Drilling-Drywall-Plastic-Anchors-Screws/dp/B01FCZ8I3I
These type of plastic anchors might be a solution to pressure dings from hard turns or knees or however they originate. The anchors would distribute the pressure down into the foam, instead of the pressure only being at the surface. Pressure dings can lead to delaminations.
Does anybody make surfboards using polyisocyanurate closed cell foam?