Reddit Reddit reviews Squadron Products Value Pack Sanding Stick

We found 20 Reddit comments about Squadron Products Value Pack Sanding Stick. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Abrasive & Finishing Products
Sanding Sticks
Abrasive Finishing Products
Manual Sanding Products
Squadron Products Value Pack Sanding Stick
Includes 5 long tapered sanding sticksIncludes, a fine, fine medium, coarse and tri-grit abrasive sanding sticksThis sanding stick can be used either wet or dryPackage dimensions: 8.625" L x 1.5" W x 1.0" H
Check price on Amazon

20 Reddit comments about Squadron Products Value Pack Sanding Stick:

u/ggorgg · 6 pointsr/modelmakers

Invest in some good side cutters and some sanding sticks. . Don’t stress if you make mistakes, just do your best to finish the model. You’ll learn a lot just by getting it finished as best you can. Then try another kit.

u/JohnnyZondo · 3 pointsr/modelmakers

These may be of some use to you.

Be gentle sanding as well, you dont want to take off any detail. Ive done that :(

u/wolfkeeper80 · 3 pointsr/Gunpla

I have one but they're a little rough for model kits.

I use something similar to these: http://www.amazon.com/Squadron-Products-Value-Sanding-Stick/dp/B000CDR5K8

u/Type43TARDIS · 3 pointsr/Gunpla

I have found that the easiest (and cheapest) way to up your model kit game is to panel line them. It makes the color separation pop way more, and helps define the proportions of a kit much better. A three pack of the panel linking markers are on Amazon for 5-7$ usa (link below). I recommend using the gray marker for white parts, brown for red orange gold and yellow parts, and black for blue gray and silver parts. The markers last a very long tine as well.

Another way is to buy some sanding sticks (10$ roughly for a 4 pack) and work on carefully removing nub marks. It will really improve the final presentation on the finished model. Start with a lower grit stick to remove the nub, and then increase the grit to polish away the scratches. If done correctly (I'm still working on this too) it will look like the nub was never there.

I Hope this helps, from one modeler to another.

Panel lining markers:

GSI Creos Gundam Marker Value Set -GM01&02&03- (Black, Gray, Brown) https://www.amazon.com/dp/B00HY93GHY/ref=cm_sw_r_cp_apa_i_xt-2DbKF7CZZR



Sanding sticks:

Squadron Products Value Pack Sanding Stick https://www.amazon.com/dp/B000CDR5K8/ref=cm_sw_r_cp_apa_i_AC-2Db3ZFSJ3K



Edit: also the panel lining will help the paint job pop. In addition I'd saw use multiple coats from the gundam makers if possible.

u/TheSunIsActuallyCold · 3 pointsr/Warhammer40k

Files are okay but I preferred filing sticks staring with coarse and then moving up through till you get to a fine finish

Sanding stick set Coarse Medium Fine Extra Fine Tri-grit # 30506 https://www.amazon.co.uk/dp/B000CDR5K8/ref=cm_sw_r_cp_api_i_k.TvCbVEXY7JZ https://i.imgur.com/HBIUU8r.jpg

u/The_Squiv · 2 pointsr/Gunpla

Thanks for the tip, I’ll keep that in mind. Right now, I’m starting at the feet and working my way up.


As for the sanding sticks, they’re Squadron brand . They’re inexpensive but they’re fantastic. The only downside is that they don’t have a grit rating on them. But it comes with a Coarse, Medium, Fine, Extra Fine, and a Tri-Grit, which is good for finishing. The amazon pack shows that it comes with a finishing stick, but it doesn’t. It instead has an Extra-Fine grit stick. I find myself using the medium, fine, extra-fine, and tri-grit sticks pretty often. I’ve yet to need the coarse one.


I’d highly recommend the brand. They’ve served me well and I plan to get more when these wear down.

u/churchxc · 2 pointsr/Zoids

Definitely get a good pair of hobby side cutters. This is what I use, and I've had it for a year and a half and it's still really sharp and leaves almost zero stress marks right against the plastic. There's cheaper ones out there, but you'll need to cut farther away from the piece and then use an exacto knife. Then use sanding sticks to get everything flush.

Sorry if you know all this, just saw the nail clipped comment and they're definitely not the best idea on a kit, especially if you just spent 80 bucks on one.

u/Iowa_Dave · 2 pointsr/3Dprinting

I use these sanding sticks a lot. I also use foam sanding blocks which make it a lot easier. I use really coarse like 80-100 grit and a light touch to knock down the layer ridges. Then I prime with the filler-primer and go back with 120 and then 400 grit paper.
Wet-sanding can get you an almost glass-like finish if you want, but it's a lot more time.

I generally sand/prime/paint individual pieces that are seperate colors. I leave some PLA exposed for some two-part epoxy which is AMAZING for holding PLA.

I've linked to AMazon but Home Depot/Lowes will have the sanding blocks and your local hobby-shop will have the epoxy, sanding sticks ad two-part epoxy.

For wood PLA I had to go a little lower than usual with my nozzle, it printed really well at 190°C and I had to print slow about 30mm/sec.

u/Ahhhndrew · 1 pointr/Gunpla

The sanding tools I use are Squadron sanding sticks from Amazon. They are a god send. Careful sanding should be able to finish off the residual rectangles you're seeing.

u/Vonderboy · 1 pointr/Gunpla

I use hard Wave sticks too and love them. They sand very flat (something I liked files for) but are quite gentle on the plastic in terms of deap scratches. BUT for some reason the 800 grit is disconnected like in your link. Anyone know where else you can get it?

In terms of files I have the Tamiya basic , Tamiya fine basic , and a (hopefully) nicer plastic hobby file on order just to try. Files are nice for larger jobs like serious molding flaws (not common in Bandai kits) and the fine ones are OK for nubs but still quite rough compared to any sanding stick. Although, as you know I'm sure, files last forever and require much less effort and time to chew through plastic. I'm hoping the plastic file is the Holy grail and is a good balance. I bought a set of needle files and diamond files from harbor freight and they blow. The trash just don't grip or cut don't waste your $3.

And as a reference I own Revell, squadron , nail buff sticks, and have made my own sticks from automotive sand paper. The nail files are way too rough imo, making my own is a pain, and while the squadron sticks are nice I mainly only used the tri-grit while I used all the Revell except the roughest and are probably the best value imo. I still use the other more flexible kinds but dramatically prefer wave. Wish the 800 grit still were available.

Long post sorry. Hope it helps

Edits: spelling, phrasing, and lots of links

u/Lock-kun · 1 pointr/Gunpla

I've seen the x-acto chisel blades recommended for nub removal. The standard diagonal ones have been a bit less effective than I'd like. Should I just bite the bullet and go with sandpaper/sticks though? And if so what should I get? There's the sanding stick set here that I've seen used, and the sandpaper set recommended on the link on this wiki's lowest grit is 1000, where I've seen starting with 400 and working your way up on nubs recommended, so should I look at a different set?

u/_Whammo_ · 1 pointr/Gunpla

You can combat this with these. I use a 600 grit that I get from a local hobby shop, then in this pack, I use the fine stick, and then the ultra fine stick. It brings back that glossy sheen.

​

Also, keep in mind that a matt top coat will hide a lot of these sanding marks.

u/robotbara · 1 pointr/Gunpla

so im looking to start seem line removal and i have checked a few tutorials as well as the sticky, and i cant seem to figure out what types of sandpaper/ sanding sticks to get. this has good reviews on amason. do yall think thos would be fine ? Squadron Products Value Pack Sanding Stick https://www.amazon.com/dp/B000CDR5K8/ref=cm_sw_r_cp_apa_N4gpzbYNR9N5S

u/WarpathII · 1 pointr/Gunpla

My Typical nub removal process looks like this:

  • Snip from runner far away from the piece.
  • Snip leftover nub from piece.
  • Lightly file nub to the base. I use this Squadron File set.
  • Use sanding sticks from a fine to Tri-Grit/polishing. Again I use Squadron Sanding Sticks

    It takes a bit longer, but it typically gets rid of all of the stress marks and nubs and you avoid cutting too deep. I just had to refinish my Denial Gundam because of deep cuts I made 6 months ago when I just used a knife.
u/AnDo117 · 1 pointr/Gunpla

I use these sanding sticks. Starting with medium then working my way up to the super finishing stick. Then I use a scrap tshirt swatch to buff.