Reddit reviews Stainless Steel 304 Cast Pipe Fitting, Flange, Welding Spud, Class 150, 1" NPT Female
We found 2 Reddit comments about Stainless Steel 304 Cast Pipe Fitting, Flange, Welding Spud, Class 150, 1" NPT Female. Here are the top ones, ranked by their Reddit score.
Welding spud flange for joining two sections of a piping systemFemale National Pipe Taper (NPT) threads for use with male threaded pipesMade of stainless steel 304 for strengthLow carbon content to ensure greater resistance to corrosionMeets specifications ASTM A182 and ASME SA182 for quality assurance
I built one of these to use as a stripping still since I ferment in 5 gallon buckets. It works great actually. At the basic level all you'd need to do is cut a hole in it and tig weld (or silver solder) a fitting into it for a water heater element. I'm using a $10 110v 1500w water heater element. Throw the sidebar Pot Still head on it and you're golden.
Cuts are easier and more precise on a larger still for sure, but many of us started out with a stove-top kettle and it is possible to make acceptable cuts at that size. My first few spirit runs were done with a 3 gallon wash capacity pot still I made from a 4 gallon stainless steel cooking pot and the sidebar pot still arm. I'd say it rivaled any bottom-shelf commercial product, but I could be biased. It was definitely acceptable drink to me and everyone I shared it with.
I say if that's what you have room for, go for it. It will work well for you and you can always upgrade later to larger sizes if you have room.
Do you mean 1/4 barrel? I'm making a Boka out of a 1/2 barrel keg (15.5 gal). Here's what I've bought:
5' of 2" copper DVW pipe - Local hardware store
25' of 1/4" copper refrigeration coil - Local hardware store
Stainless steel pot-scrubbers - Walmart
Clamp ferrule:https://www.amazon.com/gp/product/B00835O0J6/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
1500W heating element: https://www.amazon.com/gp/product/B0006IX89Q/ref=od_aui_detailpages00?ie=UTF8&psc=1
Fitting for heating element:https://www.amazon.com/gp/product/B003GSL0S4/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
Triclamp:https://www.amazon.com/gp/product/B00ED2EZCK/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
Triclamp gasket: https://www.amazon.com/gp/product/B013S1M75I/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
Thermometer:https://www.amazon.com/gp/product/B0198473E4/ref=ox_sc_act_title_1?ie=UTF8&psc=1&smid=A24QHZSKPYNZBC
Flux:https://www.amazon.com/gp/product/B000V88WJW/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
Lead-free solder: https://www.amazon.com/gp/product/B0002JM8D6/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
I am going to start by forgoing the Liebig condenser as I don't think its terribly necessary and it can always be added easily just after the compression-fitted valve. The hardest part was finding 5' of copper pipe, everyplace wanted to sell me 10' and the prices were all over the place.
Hope this helps!