Reddit reviews Switchcraft Short-Frame Toggle Switch w/ Black Switch Tip
We found 5 Reddit comments about Switchcraft Short-Frame Toggle Switch w/ Black Switch Tip. Here are the top ones, ranked by their Reddit score.
Short Frame Toggle Switch3 Position for 2-Pickup GuitarsPerfect for Semi-hollow, or narrow solid body (non-carved top) Les Paul's - Epiphone and JuniorsBlack Switch Tip IncludedPlease note!! Lugs are tinned at the Factory for easier soldering.
That switch should work fine, provided it wasn't assembled poorly, those are the dice you roll with the cheaper parts. They're not complex machines at all, so if you get one that was put together poorly, you may be able to fix things yourself. And you may get one that works fine, or works fine at first. But if you can afford a Switchcraft for about twice the cost, you'll have something that should be more reliable and durable.
Those are standard sized humbuckers and you should be able to replace them with any standard sized humbuckers (aka Gibson sized, not Fender sized - Fender sized are larger, but almost no one makes Fender sized pickups). For your budget, I'd highly recommend GFS pickups. GFS pickups are just fine and a great value for the money.
But pickups are just wire wrapped around magnets when it comes down to it. Where is the rust? On the pole pieces? Are the lead wires from the pickups intact and not corroded? If it's just the pole pieces that are rusted, that shouldn't be a big deal actually, you can clean that off. The real problem would be corrosion of the coil wires and/or breaks in the wire. If you have the patience and focus of attention to do it right (and to research how to do it right!), then it's actually feasible to unpot the pickup (remove the wax), unwrap the wire, clean it, clean the poles and the magnet, rewrap the pickup wire, and repot the pickups. It's extremely tedious and time consuming (you're talking about at least 6k to 7k wraps around the coils!), and humbuckers are more complex than single coils because you have to make sure that the two coils (north and south -> as in magnetic north and magnetic south) are reverse wound and reverse polarity.
Honestly, unless you have the right tools, patience, a keen sustainable interest in the work, and a LOT of time, it does just make the most sense to buy new pickups, but hopefully if you dig around the links in this post, you'll stumble on some useful information about pickups and guitar maintenance that you can dig into. Youtube has a metric ton of resources for guitar maintenance, repair, setup, and building. Dig in!
Even if you want to replace your pickups with new ones, you'll still need tools. What tools do you have or have access to? Do you have a soldering iron, solder, and a solder sucker? Do you have contact cleaner for electronics? Do you have anything to use to clean rust off contacts (be mindful of toxic chemicals)?
Is there any chance you can get your hands on a multi-meter? Maybe borrow one? These are indespensible when you're trying to figure out whether you have a broken component or bad wiring.
While you're working to replace the switch and pickups, be absolutely certain to check the existing wiring and make sure that nothing's corroded, loose, or broken. Most problems with pickups (assuming the pickup wires aren't corroded or broken), are actually problems with the control electronics and wiring. Since you'd be in there soldering up a new switch and possibly new pickups, it would be a good time to replace the wiring. You can get shielded guitar circuit wire from Amazon, but it's cheaper elsewhere, like Guitar Electronics.
You don't - you just replace it.
This is a very easy job if you have a soldering iron and aren't a complete moron.
Document/photograph/label the wires as they are on the current switch and put them in the same respective spot on the new switch.
Curl the wires into a hook shape and feed them through the holes on the new switch to form a physical connection to make a stronger connection and the soldering process easier.
Steal the knob tip from the old one and put on the new switch.
If you want to go through all the trouble of sending a guitar back to a manufacturer/store for this kind of repair that's your business but it's kinda like sending your car away because you've got a flat tire.
The best option may actually be a 3 way toggle switch. It won't be 24/30mm, rather a much smaller toggle. Try a guitar switch or something of that nature, here's a link!
https://www.amazon.com/Switchcraft-Short-Frame-Toggle-Switch-Black/dp/B00LYFFW9O/ref=pd_lpo_vtph_267_lp_t_3?_encoding=UTF8&psc=1&refRID=PD3K1NNRJR25BK5SYZXP
I just put one of these in my PRS SE Akerfeldt.
https://www.amazon.com/Switchcraft-Short-Frame-Toggle-Switch-Black/dp/B00LYFFW9O/ref=sr_1_4?ie=UTF8&qid=1493126956&sr=8-4&keywords=switchcraft
http://www.amazon.com/dp/B00LYFFW9O/
Switchcraft brand switches are some of the best on the market, so next time you need to replace switches/input jacks, I'd recommend them highly.