Reddit reviews Tenergy TB6AC 50W/5A AC/DC Dual Power Balancing Charger for NiMH/NiCD/Li-PO/Li-Fe/SLA
We found 9 Reddit comments about Tenergy TB6AC 50W/5A AC/DC Dual Power Balancing Charger for NiMH/NiCD/Li-PO/Li-Fe/SLA. Here are the top ones, ranked by their Reddit score.
TB6AC can accept three types of Lithium batteries - LiIo, LiPo and LiFe.High-power and high-performance circuit:maximum output power of 50W.Built into the smart charger is an individual-cell-voltage balancer. No external balancer is needed when chargingLithium battery Fast and Storage mode: The smart charger offers additional Lithium programming. Fast charge reduces the charging time of the Lithium battery and the Storage mode controls the final voltage of the battery to be suit for long time storage.Supports the following connector types: Tamiya, Mini Tamiya, JST, Hitec, EC3, Deans
Hands down best bang for your buck. Comes with all cables and connectors needed
I have had one for 6 months and just ordered my 2nd
Tenergy TB6AC
I don't have time to write a book, but here are a couple of things I can share. I boxed up my stuff 20-25 years ago. We all ran RC 10s with NiCads. We all used Novak ESCs (T1 and T4). Futaba and KO Propo for radio.
Motors - Look at the motor/ESC combos that are available.
ESCs - Again look at the combos. Castle makes some nice stuff and they have software so you can program the ESC from your computer. It is very annoying to program an ESC based on flashing lights and beeps. http://www.castlecreations.com/products/castle_link.html
Receivers - I tried to use my old Novak receiver and Futaba, but it wasn't reliable. I broke down and just got a new Futaba set. There is a company called Fly Sky that makes very inexpensive transmitters that I hear are not that bad.
Servos - The big thing here is more power and strength due to the rock crawler crowd. A lot more options now.
Batteries - I tried to use NiMH and now realize I should have just gone straight to LiPo. LiPos supposedly are a little volatile and should be stored in a liPo sack to prevent against fire. I bet you have to do something really stupid to make them dangerous though. They also need to be put into storage mode if they are not going to be used for a while. This just means they need to be charged to a certain amount. I do what is called a balanced charge each time I charge them. This means that each section of the battery is at the same voltage. I have been using this charger and it works well. http://www.amazon.com/gp/product/B00466LEMC/ref=pd_lpo_sbs_dp_ss_3?pf_rd_p=1535523722&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B003EJD8HG&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=0XZERFQM3FBSQ820RX7E
Chassis - Correct, not much difference here especially when you look at brands like Team Associated or Tamiya. There are some new brands out there that make some nice stuff like Axial.
Hopefully someone with more time can elaborate . . . . especially on the battery stuff because it is a bit complicated.
Is Imax and Tenergy about the same reliability do you know? I can get a Tenergy one with built in power for about $20 more and it comes with a couple more leads. http://www.amazon.com/Tenergy-TB6AC-Power-Balancing-Charger/dp/B00466LEMC/ref=sr_1_3?ie=UTF8&qid=1412569389&sr=8-3&keywords=Tenergy+TB6-ac+Balance
I want to keep it compact so I can use it when I go out camping and hiking. I have a converter for my Jeep and a solar generator that can power the charger and it would be nice to not have to have an extra brick to carry and cut on weight.
Mode 1 right throttle, mode 2 left throttle. i think most use mode 2?
Turnigy 9XR doesn't come with a module (tx and rx), so you need a set of those.
If you are trying to save money, maybe something like this?
If looking for something to use with other stuff in the future, I would get something like this. it comes with the tx/rx
I got one of these for a charger.
disclaimer: I am a noob at this (2 months) so take with grain of salt!! -lol
Yes that is the one I currently have. I also believe based on the current running of the 1800MaH battery pack that it wont be able to handle a LiPo battery. It takes 2 hours because its the standard crappy wall charger that came with the car, so I know I need a new charger. I see alot of recommendations to get one of these http://amzn.to/1rpiWDq . Is there a reason to not go big on the LiPo right now? I want something that can be used on a future RC car, and if I can get something decent now I wouldnt mind. Is there specific ESC you might recommend to run on this buggy with a LiPo battery and a brushed motor? I just want to be able to upgrade in the future and any purchases I make on this just transfer them over. I should have gone brushless (DOH).
was thinking of going with this ESC : http://www.hobbyking.com/hobbyking/store/__32025__HobbyKing_X_Car_45A_Brushed_Car_ESC.html.
Is there something I can get that would allow me to run a slightly bigger battery since I am limited to 7.4v-2s?
Can you help me choose a battery with power and long run time?
Why don't you list out the features you need or want. And also desired and acceptable flight times.
Some things to think about...
Example Hex... Little under the cost of a Quad Phantom 2 V+ and a good bit under the Quad Iris+ while giving you some protection against a single motor/prop failure.
On chargers, amazon is your friend I found this in two minutes (and it's also the one I use personally). On lipos, Intellect/Firefox are a go-to for me.
P.S. You shouldn't be using an 11.1v without a mosfet.
I did some research on charging a battery while driving and decided that something like this would work.
That one would work, however it is made for NimH batteries, so if you ever switch over to a LiPo battery in your gun you will have to get a different one.
https://www.amazon.com/Tenergy-TB6AC-Power-Balancing-Charger/dp/B00466LEMC/ref=sr_1_3?s=toys-and-games&ie=UTF8&qid=1483824779&sr=1-3&keywords=smart+charger+lipo+nimh
This one is a little more expensive but it will make sure you are able to use any battery on it. Really depends on how much money you are willing to spend. :P