Reddit Reddit reviews Ubiquiti UniFi Switch 8 60W (US-8-60W),White

We found 43 Reddit comments about Ubiquiti UniFi Switch 8 60W (US-8-60W),White. Here are the top ones, ranked by their Reddit score.

Computer Networking
Computer Networking Switches
Electronics
Computers & Accessories
Ubiquiti UniFi Switch 8 60W (US-8-60W),White
Connectivity Technology: Wi-Fi Ready
Check price on Amazon

43 Reddit comments about Ubiquiti UniFi Switch 8 60W (US-8-60W),White:

u/KingdaToro · 13 pointsr/HomeNetworking

All you need:

1x UniFi Security Gateway


2x UniFi AP AC Pro

Optional: 1x UniFi Switch 8-60w. You will need some sort of switch as the USG only has one LAN port. You can use an ordinary unmanaged switch, which will be much cheaper, but then you'll need to use the PoE injectors to power the APs (they're included with the APs). This switch will power them on its own.

Optional: 1x UniFi Cloud Key. This is just a dedicated device for running the UniFi Controller, which is what you use to configure and manage all UniFi devices. You can run it on a PC instead if you want.

But since you're doing a total gut renovation, you should take the opportunity to do your network right. Your goal shouldn't be to put everything on Wi-Fi, it should be to put as many things as possible on Ethernet, and just use Wi-Fi where Ethernet isn't an option. Anything that stays put, i.e. TVs, desktop computers, streaming media players, game consoles, even printers should always use Ethernet if they support it. The more things you get off the Wi-Fi, the faster it'll be for the things that need it.

First, figure out where your network hub will be, all your lines will run to it. It's where you'll have your modem, router, and main switch. The best location is a basement, but if you don't have one, use a utility closet/room. Make sure the location is ventilated and not too hot.

Next figure out how many Ethernet lines you need. Minimum is one to every location where you'll have a TV or desk, but this is likely to necessitate additional switches. Ideally, you should run five to the location of your main entertainment center and two to every other TV and desk location. You'll also need one for each AP, these will run to the spots on the ceiling where you'll put the APs. You'll also want to run a coaxial cable to each TV location. Once you know how many Ethernet lines you need, you need to get at least that many punch-down keystone jacks (minus two, as the AP lines won't need them), a punch-down patch panel with at least that many ports, and a gigabit switch with at least this many ports (plus one for the router). Make sure your patch panel and jacks match the category rating of your cable, i.e. Cat5e or Cat6. You'll also need a few RJ45 plugs (get ones made for solid-conductor cable) and punch-down and crimping tools.

For the cable, you'll want solid conductor, pure copper cable. Don't get stranded cable, and don't get cable made of copper clad aluminum (CCA). Make sure it's riser rated, but don't get plenum rated cable. Cat5e is all you need for gigabit, and it's cheaper and easier to terminate. Get Cat6 if you want to future-proof for 10 gigabit. Get a 1000 foot bulk spool, Monoprice is a good place to get it.

You'll also need a bunch of pre-made Ethernet patch cables. You can make your own, but it's tricky to get right and time-consuming. You'll first need one for connecting each patch panel port to a switch port. These should be as short as possible, 1-3 feet. Two more for connecting the switch to the router and the router to the modem. Two more if you'll be using the PoE injectors to power the APs. All of these should still be as short as possible. Then you'll need one for connecting each Ethernet-using device to one of the wall jacks that you'll be installing, these should be 6 feet or longer if necessary.

When you do the install, first mount the patch panel at your network hub location. Run each line from the patch panel to a keystone jack, which will go in a keystone wall plate which mounts to a low-voltage bracket. The AP lines won't get keystone jacks, these (and only these) will get RJ45 plugs to connect directly to the APs. Once all the lines are installed, set up the main switch. Connect each port of the patch panel to a switch port. If you're using PoE injectors to power the APs, connect the PoE port of each injector to an AP port on the patch panel and the LAN port to the switch. Finally, connect the router's LAN port to the switch and the router's WAN/Internet port to the modem/ONT.

u/IbyFoReal · 5 pointsr/HomeNetworking

I personally really like and enjoy the Ubiquiti 8 port switch:

Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.ca/dp/B01MU3WUX1/ref=cm_sw_r_cp_api_i_nrLUCbQ1EA5N7

u/qupada42 · 4 pointsr/networking

Ubiquiti access point(s) and their "Cloud Key" controller for management/captive portal springs to mind.

Optionally, depending on how point-and-click you want the management for this deployment to be, also their "USG" router, and a US-8-60W PoE switch to complete the UniFi hardware set.

Amusingly, on amazon.de (used as an example to get EU pricing), those four items together come to €499.34 (UAP-AC-Pro, US-8-60W, USG, UC-CK). How's that for ever so slightly under-budget?

It would need a small amount of work customising the captive portal if you want to do social media logins - I've never done that personally, but someone might know the details. Their forums would be a good place to start if you want to look for someone who has done that, or general advice.

The gateway is definitely optional, and any cheap PoE switch would be fine (or non-PoE, as the AP will also ship with a PoE injector). The controller software can be run on any old PC or VM with 1-2GB of RAM (although I personally like the cloud key for convenience), so you could get the cost down as low as just the AP if you've got a switch and a spare computer.

It also gives you a nice ability to expand with another AP in future if this takes off and you need extra capacity, and a nice management interface which is optionally accessible over the internet without being on-site, which might be nice if you have to help troubleshoot this remotely.

u/phys_teacher · 3 pointsr/Ubiquiti

The USG does not operate like a switch - LAN 1 and 2 are treated as completely separate networks, so devices on each will not be able to see each other without some fancy firewall rules. I would recommend some sort of switch instead, not necessarily one from Ubiquiti. The benefit of the Unifi switch is that it is managed (can be programmed) with power to 4 devices. A regular switch will be fine too, as long as you use the PoE injectors that come with the APs.

Here's the switch I have: https://www.amazon.com/gp/product/B01MU3WUX1/

Any of these would work - some provide power, and I'd recommend a 1000 Gbps switch: https://www.amazon.com/s/node=281414

A controller is only needed if you want to make any changes to your network, such as the WiFi name or passwords, or if you want to view some of the network statistics. It is also used to run the guest networking portal.

You can use the free controller download if you only plan on making the initial configuration and don't want anything else. If you plan on a guest network, statistics, or make changes often, a cloud key would be good to have.

u/QuadTechy88 · 3 pointsr/htpc

Might I suggest a more prosummer solution.

Look at ubiquiti gear. It’s what I run at my home and we deploy there access points and switches at over 200 customers. They are excellent for the price

Gateway/router
Ubiquiti Unifi Security Gateway (USG) https://www.amazon.com/dp/B00LV8YZLK/ref=cm_sw_r_cp_api_HE45BbH0YVZR8

8 port Poe switch
Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_api_hF45BbGNDVBBR

Access point
Ubiquiti Networks Unifi 802.11ac Dual-Radio PRO Access Point (UAP-AC-PRO-US) https://www.amazon.com/dp/B015PRO512/ref=cm_sw_r_cp_api_XF45BbNXXZSJ2

These products will allow you to make sure your wireless network is on something with the least interference, you can also band steer clients to use the less congested 5ghz band all on the same wireless network. Instead of having to make a separate one 2.4 and 5. Which is what most all in one home devices do.

This will over all be a much more flexible system as well. Find an area that doesn’t have good WiFi coverage. Run a cable and add an AP there, or they can even mesh and do it with out a cable.

u/deebeeoh · 3 pointsr/HomeNetworking

I personally would just pick up one of these as well: https://www.amazon.com/Ubiquiti-Networks-US-8-60W-Unifi-Switch/dp/B01MU3WUX1/ref=sr_1_1?s=electronics&ie=UTF8&qid=1497122683&sr=1-1&keywords=ubiquiti+us-8-60w+unifi+switch

Modem -> EdgeRouter -> Switch -> AP

Your switch doubles as the PoE injector, so you don't need to use that anymore which is nice. I would leave the spare ports on the EdgeRouter unpopulated and let the switch handle all the switching leaving the router to do well the routing. IT people really know how to name stuff!

Plug your NAS and any hardwired computers into the switch. Nice thing is the switch and the AP can both be managed from the same unifi interface, so they work very nicely together.

u/wabbit02 · 2 pointsr/ubiquity

I would check pricing of buying from another supplier as well (UK based so no idea on US options). For Home you dons't 100% need the cloud key, its nice, I have one but the controller SW doesn't need to be running 24/7 unless you want a portal (auth)/ stats etc (as far as I am aware)

You also need to change the switch to this 60w POE (or above), the one you have selected has POE pass though (e.g. you use another switch to power it and it can then power another device) These are really neat for a "behind the TV" replacement but wont work to power the Cloud key and UAP

You should also consider the new nanohd - $30 more but has MU-MIMO - that said I haven't really seen the reviews on it.

u/macbalance · 2 pointsr/HomeNetworking

I have one of these:

https://www.amazon.com/gp/product/B015PRO512/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Which connects to one of these:

https://www.amazon.com/gp/product/B01MU3WUX1/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

The Switch connect to the FiOS Gateway. I wouldn't mind adding a second (or even 3rd) AP, but money is always an issue. The Switch and the other Gateway interaces have several other devices on it:

  • 2 Desktops (One is the 'server' I mentioned)
  • Home NAS
  • Work Special Access Point
  • 'Lab' Router

    The AP has a pass-through which connects to a no-name switch (that I need to replace) that provides connectivity to the entertainment center stuff (AppleTV, TiVo, game consoles, etc.)

    I'm pretty minimal by many people's standards. If I move I'd like to switch to using one of Ubiquiti's USG Firewall/routers and a dedicated controller so I can do wireless guest access better.
u/jabbyknob · 2 pointsr/TeslaModel3

Don’t use that netgear garbage. Ubiquiti makes really nice enterprise class network equipment which is super simple to set up and manage. At a minimum, all you need is cat5-e (cat 6 fine too) distributed around the house and a couple access points connected to the hard lines:

Ubiquiti Networks Unifi 802.11ac Dual-Radio PRO Access Point (UAP-AC-PRO-US) https://www.amazon.com/dp/B015PRO512/ref=cm_sw_r_cp_api_i_gHiRDbHKHSSRR

(2 access points cover my 2500 sqft house and a third covers my detached garage and back yard)


You can optionally buy a PoE switch (power over Ethernet) to connect to the access points so that the power is transmitted through the network cable and you don’t have to plug them in to a wall outlet. This will work if you choose this route (you will have to configure this switch to turn on PoE on ports connected to access points).

Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_api_i_nNiRDbW2HP8HG


Any one of these progressive options is a valid stopping point, but I recommend buying the secure router/gateway and then the cloud key. These allow you to do advanced network management (main + guest Wi-Fi networks, custom qos throttling):

Ubiquiti Unifi Security Gateway (USG) https://www.amazon.com/dp/B00LV8YZLK/ref=cm_sw_r_cp_api_i_1RiRDbW5SEFNM


Ubiquiti UniFi Cloud Key (UC-CK) https://www.amazon.com/dp/B017T2QB22/ref=cm_sw_r_cp_api_i_vSiRDb8SMX7ZY


The guest network is worth the price of admission for added security. Put all your random wireless devices (i.e. the internet of things) on this network to isolate them from your major devices (PCs and phones). Reason being the IoT devices are frequently hacked and used to access your home network.

u/SirEDCaLot · 2 pointsr/homesecurity

Okay here's some background. Cameras come in a few types.

Old school cameras are analog. Each camera gets a coax analog video line, and a DC power cable. In the olden days those coax cameras recorded onto analog tape. In the slightly more modern olden days, a DVR (Digital Video Recorder) device would have many analog inputs and would record the video to a hard drive.
You DON'T want that.

Today, we use IP cameras. IP is Internet Protocol- means the cameras are fed one Ethernet line, generally PoE (Power over Ethernet). That means one Cat5/Cat5e/Cat6 cable can feed the camera both power and data connection.

There are also now WiFi based cameras. Those cameras are much like IP cameras, in that they use Internet Protocol, but they use WiFi instead of hardwired Ethernet. That means they must be plugged into a 120v power outlet. The WiFi cameras I'm talking about use a NVR on the network, just like normal IP cameras.

Finally, and in a totally separate category, are cloud-based cameras. These are proprietary products like Ring, Nest, Arlo, etc. While they are WiFi IP cameras, they ONLY communicate with their own proprietary cloud service. So you could have a ton of hard drives at your house, you can't use any of them; you have to pay for the camera manufacturer's cloud storage service. I suggest NOT getting this sort of camera, mainly because you have to pay for the storage forever, and also because it is constantly uploading (mostly-useless) video over your Internet connection.

There are a lot of popular 'surveillance in a box' type products. What those usually have is an all-in-one NVR (Network Video Recorder) that has several powered Ethernet ports for cameras, and a hard drive, as well as 4-8 IP cameras. Hikvision makes a LOT of these, and they're not terrible, but IMHO you can do better especially as Hikvision security isn't the best.

Ubiquiti is another company that makes IP cameras. With Ubiquiti hardware though, you do it on a piece by piece basis- you get a PoE Ethernet Switch to plug the cameras into, and the cameras themselves, and the Cloud Key + Gen2 is your NVR (it plugs into one of the switch ports).
This diagram shows what a complete Ubiquiti UniFi network would look like... it's more complex than you need because you don't need the router (UniFi Security Gateway), or the WAP (UniFi AP). You already have a router and WiFi. So you just need the cameras, a PoE switch, and the NVR.

While all that sounds complex, it really isn't. Here's what I'd do:

$190 Cloud Key Gen2+
$107 UniFi Switch 8-port 60W PoE
$381 UVC-G3-Bullet-3 Camera 3-Pack

Result is for $678 you have a nice very good quality surveillance system. You can access it remotely from your cell phone. It will record for quite some time with no monthly fees ever.
To set it up- take the 8 port switch. Plug the Cloud Key Gen2+ and the 3 cameras into the 4 PoE ports. Plug any of the non-PoE ports into your existing router. Then fire up the UniFi app on your phone and configure it.

u/spychipper · 2 pointsr/HomeNetworking

As stated elsewhere you will need a managed switch.

If you are on a budget my go-to for over a decade has been various revisions of the Netgear GS-108t

If you want ease of use these days I would go with Ubiquiti. for home use. The linked switch is 2x the cost of the Netgear, but provides Power Over Ethernet (PoE) which allows you to use Ubiquiti's matching Access Points at some point in the future, both of which can be managed from the same interface. Note that the AP linked to is an example, they make different models for different use cases. The management interface shines if you are not a networking pro.

u/0xBADB17E · 2 pointsr/cybersecurity

Offhand I don't have any solid recommendations. I think this Ubiquiti switch has port mirroring. The spec sheet mentions it but doesn't get into details. Cisco has it on many of their devices but refer to it as 'SPAN'.

A network tap would be a superior option, but they get expensive if you need anything over 10/100baseT.

You can also pick up used gear from craigslist. I've used an old Cisco ASA5505 for years since my internet never breaks 100 Mb/s.

u/robin_flikkema · 2 pointsr/raspberry_pi

You're talking about the PoE hat?

Get a switch that has at least 4 ports of 802.3af and a rating of at least 50-60W (calculated by 5V 2,5A 4 RPi's).
You don't need to worry about voltages and amperages of the switch as long as it supports 802.3af and has a total wattage of at least 50-60.

The USW-8-60W would probably work or a TP-Link SG1005P or a Netgear GS305, haven't tried these personally with 4 RPi's but it should work

u/Shrappy · 2 pointsr/sysadmin

You'll want some Ubiquiti equipment for this functionality and price point. Ubiquiti wifi AP's can broadcast multiple SSIDs, each on their own VLAN. Back that with a ubiquiti switch which also supports vlans, and you should be good to go.

Swtich here, AP here, and I'd recommend a new router so you know the vlan segregation extends all the way to the firewall, so here's the USG.

Granted, VLAN's are not a security tool and it is relatively easy to bypass them, but this should do for home use.

u/MalfeasantMarmot · 2 pointsr/HomeNetworking

The unifi APs will handle all of the roaming. They don't need the controller up and going to do it. They'll operate on different channels and leave it up to the devices as to which one to use at any given time. I have two and often don't have the controller running and my devices switch back and forth without issue.

I'd consider getting one of the unifi switches as well. Then you have the manageability that comes with that. It might make things run a little smoother, but it isn't required. This one is a good way to go to start with, it will also power your APs. This is the one I started with, though it is a little more expensive.

I like having the ability to manage VLANs through the switch itself, especially if you're running a server.

u/beersykins · 2 pointsr/HomeNetworking

The Ubiquiti US-60W isn't too horrendous.

https://www.amazon.com/Ubiquiti-UniFi-Switch-60W-US-8-60W/dp/B01MU3WUX1

You could pick up a used Nortel 5520 or something for $20 but they're pretty noisy and less convenient.

Do you need any specific features other than maybe VLAN?

u/DEKEBLUE4 · 2 pointsr/homelab

Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_apa_i_OEHhDb027TY47

You're talking about something like this?

u/bigbonelessjerk · 2 pointsr/HomeNetworking

I need to build a whole new network because the cable modem is only the Spectrum bare bones with nothing but a wired connection. If I'm seeing this correctly, I would need the EdgerouterX plus the Ubiquiti Unifi Ap-AC Long Range plus a [switch] (https://www.amazon.com/Ubiquiti-UniFi-Switch-60W-US-8-60W/dp/B01MU3WUX1/ref=pd_bxgy_147_3/134-2367728-7655000?_encoding=UTF8&pd_rd_i=B01MU3WUX1&pd_rd_r=441ae487-d265-4bf9-bee1-32808368ecd6&pd_rd_w=m61Fs&pd_rd_wg=RryX3&pf_rd_p=a2006322-0bc0-4db9-a08e-d168c18ce6f0&pf_rd_r=RWYB945JJK6S08X1HX3V&psc=1&refRID=RWYB945JJK6S08X1HX3V)for the wired LAN computer to connect to in the back of the house.

I could then plug the Unifi AP into either the EdgerouterX or the switch where my main computer is plugged in with Cat5. If necessary, I could get another Unifi AP and have them plugged in at both ends of the house in a wireless mesh.

u/anboas · 2 pointsr/HomeNetworking

If you want to stay in the same ecosystem, here’s my recommendation for Ubiquity. You may need more than 1 AP depending on the layout of the house, walls and placement.

Modem: ARRIS SURFboard Gigabit Docsis 3.1 Cable Modem, 10 Gbps Max Speed, Approved for Cox, Spectrum and Xfinity, (SB8200 Frustration Free) https://www.amazon.com/dp/B07DY16W2Z/ref=cm_sw_r_cp_api_i_OdcqDbMF39946

Router: Unifi Security Gateway Pro 4-Port https://www.amazon.com/dp/B019PBEI5W?ref=ppx_pop_mob_ap_share

Switch for non PoE gear: Ubiquiti US-24 Unifi Switch https://www.amazon.com/dp/B01LZBLO0U/ref=cm_sw_r_cp_api_i_7fcqDbNRQ3ZRH

Switch for PoE gear: Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_api_i_MicqDbTHS34TA

Access Point(s): Ubiquiti Networks Unifi 802.11ac Dual-Radio PRO Access Point (UAP-AC-PRO-US) https://www.amazon.com/dp/B015PRO512/ref=cm_sw_r_cp_api_i_YhcqDb6EEP86C

u/VileBooey · 1 pointr/HomeNetworking

Would be nice to have a separate network for the Guest House since it might turn into a rental down the line. Here is what I am looking at to order from Amazon:

2x Nanostations


1x Ubiquiti Switch


1x Ap-AC Lite Wireless Access Point

Or keep the Nighthawk Modem/Router and eliminate the switch and access point.

u/clickwir · 1 pointr/Longmont

I've got NextLight and here's what I use.

From NextLight, go into a Ubiquiti EdgeRouter Lite, from that into a switch.

In the switch it all my wired devices, laptop, desktop, Roku, and a Ubiquiti UAP-AC-PRO for WiFi.

It all works great, very fast and my devices are the bottleneck, not my network.

It's not as simple and compact as an all in one wifi router job. But those are a jack of all types, master of none. The Ubiquiti router, switch and AP combo is far superior for performance and reliability.

u/blackice85 · 1 pointr/Ubiquiti

Yeah, even the US-8-60W (https://www.amazon.com/gp/product/B01MU3WUX1/ref=ask_ql_qh_dp_hza?th=1) wouldn't do it without the converters I linked earlier, as that can't do 24v.

Good news is that UBNT is moving away from the proprietary 24v moving forward, but in the meantime you need either a 150w+ switch, injectors, or a higher end AP like AP AC Pro, which takes the 802.3af/at standard.

So for your situation I'd consider whether you think you'll need to expand in the future and might want a bigger switch, or if you'd rather stick to a lower budget.

u/Tommy1024 · 1 pointr/homelab

https://www.amazon.co.uk/gp/aw/d/B01MU3WUX1/ref=psdcmw_430573031_t1_B01N362YPG this one has the eight poe ports. And is able to deliver poe without poe in.

u/ilikedamoney · 1 pointr/HomeNetworking
u/ManiacFoSho · 1 pointr/Ubiquiti

This would give you a few extra PoE ports to work with in the future: Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_api_fDrTAb3CH10B1

Keep in mind that it’s just a switch, not a router. If you need a router as well and want to stick with Unifi, you get either get an EdgeRouter (a bit daunting for beginners); otherwise you could add the Unifi Security Gateway.

If you really want to go all in, add a CloudKey so you can control your network away from home.

u/automate_the_things · 1 pointr/HomeNetworking

It would, but you'd never be able to use it with anything else in the future, since pretty much nothing is passive 24v PoE, just legacy Ubnt gear. Even Ubnt is moving to all 802.af active PoE.

I'd get this one: https://www.amazon.com/Ubiquiti-Networks-US-8-60W-Unifi-Switch/dp/B01MU3WUX1

It's configurable, so it'll do both passive and active PoE, so it's future-proof.

And yes, if you have a PoE switch, you just plug the Cat5e into the switch and then into the AP and the AP is powered.

If you buy the AC-AP-LITE in 1-packs, they come with a PoE injector (single port), so aside from clogging up a few outlets and taking up space, you don't technically need a PoE switch for a couple of APs, unless you want one (tho I think the PoE switch will be lower electricity usage, but only barely).

u/trich101 · 1 pointr/HomeNetworking

It would work. I personally would spend the extra 60 ($109 total) and get a 8 port switch, including 4 PoE+ ports vs $30 for 1 injector. Just a better investment for powering additional devices in the future. Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_apa_i_ErKYDbMB7601J

u/Hutchisonac · 1 pointr/HomeNetworking

So if I get the following:

Ubiquiti Unifi Security Gateway (USG) https://www.amazon.com/dp/B00LV8YZLK/ref=cm_sw_r_cp_apa_i_G.-6CbQKR05PA


Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_apa_i_oe.6CbNHHGH30

Ubiquiti Networks Unifi 802.11ac Dual-Radio PRO Access Point (UAP-AC-PRO-US) x2 https://www.amazon.com/dp/B015PRO512/ref=cm_sw_r_cp_apa_i_We.6Cb27RWQ13

This should be sufficient, or am I missing something?

As someone who isn't network savy, is this relatively plug and play? I can mount the access points on the ceiling and plug into the cat 6 cables. The router would then plug into my modem in the smart panel, and be connected to the switch and my 4 Ethernet lines? (2 to the access points, 1 to living room and 1 to the den/office)

u/-RYknow · 1 pointr/Ubiquiti

I'm on my mobile right now, and navigating the ubiquiti site is kind of a pain. Will the ubiquiti 8 60w switch work with the nanobeams?

​

EDIT: Scratch that, I see that switch doesn't support 24v poe.

u/GreenChileEnchiladas · 1 pointr/techsupport

I am running Unifi 8port Switch (with the Security Gateway, et al).

Though, currently I don't have the AP connected. Turns out I never really needed wireless access.

Also, now that I consider it. The Security Gateway is the Router in this situation. I just looked closer and it does have a WAN 2 / LAN 2 port.

EDIT: Rereading my statement I didn't make it clear that the Security Gateway and the Switch were two different devices. 8 Port Switch and Security Gateway.

u/hatran2 · 1 pointr/Ubiquiti

Could you look over these parts and let me know if I'm missing anything? Would I just be monitoring this stuff at my desktop that's wired in or would I need something else to control all this? I'm not sure on which switch I need.

Fiber connection>Gateway/Router> Switch 1 or Switch 2 > ethernet > AP

I am being pushed towards the in wall AP cause the fiance doesn't like things poking out from our ceiling and I was told wall mounting them doesn't work as well. From looking on their forums the UAP-AC-IW-PRO beta testers have said they are getting surprisingly good signal from their in wall AP since they have better antennas. But if I was able to go the UAP-AC-PRO route ceiling mounted how many and where would you suggest I place them?

So this is my home layout. I assumed these were the best places to put them. The red arrows show which direction the AP will be facing from the wall and the blue box is where everything terminates and I'm assuming that's where the gateway and switches will be. The ethernet drops in the living room and game room are higher up then the rest. I can have an updated picture of where all the ethernet drops are around my house if that would help.

The bedrooms near the front of the house aren't currently being used so I'm not to focused on them but I could always go back and add another AP later in that area right?

This seems like it's going to blow through my $500 budget but I'm assuming it's worth it over getting something like the Eero 2nd generation?

u/certifiedintelligent · 1 pointr/networking

So, by all rights I would heavily recommend getting a professional to do this for you, they will be available to help with any issues that crop up down the line. That saaaaiiidddd... you could also do this.

Get:

u/_munchbutt · 1 pointr/HomeNetworking

Ahh, since I do have an ac1750 in possession, would it be good enough to just skip the ac1900 instead? That way, I would have a bigger budget when I do plan on switching to the Ubiquiti APs.

Planning to get the USG, switch, and one or two APs. What else will I need?

u/JCandle · 1 pointr/HomeNetworking

Yes correct. If you have a little more wiggle room on your budget I’d add a POE switch to power the AP and give you more Ethernet ports.


Ubiquiti UniFi Switch 8 60W (US-8-60W) https://www.amazon.com/dp/B01MU3WUX1/ref=cm_sw_r_cp_api_i_9ziiDb07NS7H6

u/projxit · 1 pointr/homelab

Its called the Unifi Dream Machine, but looks like its only "Early Access" at the moment, which basically means you'd be Beta testing, but I've only heard positive things, with people saying its a lot more powerful than the USG (specifically for using things such as the IPS).

But to answer you questions:

  1. Correct, these are Layer-2 only, you need the USG/PFSense for the routing. Why do you need POE? The Unifi AP's come with a POE-Injector. Also, be aware the 16 Port switches have fans, which can generate noise, so you will probably want to stash it away (in a cupboard or garage etc).

    Personally, I do use POE, but I use their 8 Port Swich with 4 POE ports (their cheap-cheap version), along with this, I have their standard 8 port switch, see below:

    8 Port, with 4 POE: https://www.amazon.co.uk/Ubiquiti-UniFi-Switch-Port-Enterprise/dp/B01MU3WUX1/

    8 Port, None POE: https://www.amazon.co.uk/Ubiquiti-US-8-Managed-Desktop-Passthrough/dp/B01N362YPG/

    USG: https://www.amazon.co.uk/UBIQUITI-Networks-Security-Gateway-Router/dp/B00LV8YZLK/

    Cloud Key Controller: https://www.ebay.co.uk/itm/Ubiquiti-Networks-UC-CK-Stand-Alone-UniFi-Cloud-Key-Controller-BOXED/401859588968

    You don't need the last one, but I find it useful, as it gives you a physical device and it saves having to spin up a seperate VM or Rasperberry Pi for it.. And its pre-baked, you plug it in and go!

  1. Yes. You could actually even do this with 1 NIC... Thats is what I do, I just put WAN onto a seperate VLAN... After all, its just another "security zone", just like each of you internal VLANs, the reason you use VLANs, is to control routing between them.. My Virgin Hub, plugs into a port, which is Untagged on VLAN-1000, has no other VLANs assigned, the only other place that has this VLAN is my Firewall VM.

    Some people will cry "danger", and they have a point, if you are not 100% confident in what you are doing, its better to use separate NICs for LAN and WAN. This also has another issue, if you've only got 1Gb NICs, and its carrying both LAN and WAN, you've got a bottleneck (On my servers, I use 10Gbe, so I don't have that issue).
u/magibeg · 1 pointr/HomeNetworking

In the event I take the Ubiquity route I just wanted to make sure I knew what I was jumping into. So as I see it I just require the following pieces:
USG

Switch

AP

Then download the controller and i'm good to go I think with a little bit of wiring and mounting.

u/estrangedpulse · 1 pointr/Ubiquiti

So does this 150w accepts simpler ethernet connection from my router? Anyways, this is 200$ solution. Seems so expensive just for a switch. I was thinking I will get away with something cheaper. If I use 60w 8 port switch with 4 PoE, like this (https://www.amazon.com/Ubiquiti-UniFi-Switch-60W-US-8-60W/dp/B01MU3WUX1), can i plug in my non-PoE router in it? I could get 3 cams + cloud key 2 then.

u/Glynnryan · 1 pointr/HomeNetworking

TL/DR: a bit of background and personal experience ultimately suggesting that you run some network cable, and look into a full Ubiquiti setup with USG router, PoE switch & NanoHD Wi-Fi AP’s for around $400 including cabling, provided you’re not planning on upgrading your internet to faster than 1Gbps soon.


I’m not familiar with coax cable internet, but assume you can get some sort of Ethernet handoff from your modem?


Either way, make the effort and run some CAT6 cabling for Wi-Fi AP’s, and key devices too if possible.


My network setup in my 1150 square foot apartment, works perfectly on my 200Mbps fibre connection and would cost you around $483 for the following:


u/Insanereindeer · 1 pointr/HomeNetworking

From my experience, cheap POE switches are just frustrating. They lock up and have to be restarted frequently. You get what you pay for. I bought a Zxyell GS1910-24HP for $50 off ebay that I've had zero issues with. If you want new, I recommend you just match the company you have equipment from. Buying a 10/100 switch in 2019 is just ridiculous.

​

https://www.amazon.com/Ubiquiti-UniFi-Switch-60W-US-8-60W/dp/B01MU3WUX1/ref=sr_1_3?keywords=ubiquiti+poe+switch&qid=1565730365&s=gateway&sr=8-3

u/vcWfDrlqrAArebp7 · -1 pointsr/HomeNetworking

You're right. I've never actually used an adapter, as I've always just had PoE switches available. It's nice working for a company with good available resources and funding for dev/prod upgrades often. Makes more sense to put the injector on the switch side. Still, makes no sense to use them over a PoE switch, though.

Why are you assuming I'm using Ubiquiti throughout the whole network? I have an ER-X, that's my only Ubiquiti product at home. I see tons of people recommend other brands, for instance like a TP-Link AC1750 as a decent cheaper alternative to Ubiquiti APs. And look, it doesn't ship with a PoE adapter!! Dang! https://www.amazon.com/TP-Link-Wireless-Supports-Technology-EAP245/dp/B01N0XZ1TU/ Only ~$80, instead of ~$130 for a UAP-AC-PRO (Which on Amazon it says it doesn't come with a PoE adapter either! https://www.amazon.com/Ubiquiti-Networks-UAP-AC-PRO-Access-Included/dp/B079DSW6XX/ ). So here's an one adapter for $20 https://www.amazon.com/TP-LINK-TL-PoE150S-Injector-Adapter-compliant/dp/B001PS9E5I/ but wait, it can only push 15W! My Aruba APs can draw up to 25W. So less flexible, gotta get adapters for every AP, gotta power them near the switch, what a hassle.

It'd almost be awesome if there are affordable PoE switches available! Oh, look at this 8-port Gigabit PoE Managed switch for only ~$65! https://www.amazon.com/TP-Link-Gigabit-Lifetime-compliant-TL-SG108PE/dp/B01BW0AD1W/ whereas a Unifi Switch 8 PoE is ~$110 https://www.amazon.com/Ubiquiti-UniFi-Switch-60W-US-8-60W/dp/B01MU3WUX1/ Plus, you'll probably need the cloudkey if you're gonna use UAPs, so there's another $80. And might as well throw in a USG while you're at it for another $120, since OP needs a router anyways.

So, we could do your Ubiquiti stack:

  • UAP-AC-PRO - $130
  • PoE Injector - $20
  • USG - $130
  • Cloudkey - $80
  • Still will likely need some switch, unless OP has one already. USG doesn't have enough ports. Could get a good ole' Netgear GS108 for $50, only $15 cheaper than the TP-Link PoE version above, which if you're paying $20 to get an injector (and more if you need multiple injectors) that doesn't make much sense does it?

    And we'd see that setting up your Ubiquiti network will cost somewhere around $400.

    If we do the other brands:

  • TP-Link 1750 - $80
  • TP-Link SG108PE - $65
  • We can use an ER-X as our gateway since it's relatively cheap - $60

    Wow, look how much simpler that is! And it only cost around $205!

    So, remind me again in which section it's cheaper to use the PoE injectors? OP (likely) needs a switch anyways. PoE switch is $15 more expensive than non. But you're paying $20 for one injector anyways (PoE switch is like getting (Edit: 4, not 8) injectors for only $15). Did I miss anything here?