Reddit reviews UY CHAN Upgraded Original TS100 Digital OLED Programmable Pocket-size Smart Mini Outdoor Portable Soldering Iron Station Kit Embedded Interface DC5525 Acceleration Sensors STM32 Chip Fast Heat (B2)

So damn irritating. The old model had a simple dial. Same form factor. Now they don’t make them with a dial and you basically need to dig up an instruction manual to figure these things out.

OP, is there any advantage to the new one besides the fact that it led me to find the TS100 ?

Surprised nobody mentioned the cold joints, but when you redo the soldering, you can fix that as well. Basically, use your iron to heat the pad and wire together and then touch the solder to the joint. The metal will melt the solder, and it will flow right in and make a "hot" joint, which will be much more mechanically sound. It also has the benefit of guaranteeing that the flux melts; if you're not using rosin core solder, get a flux pen. The flux will etch the oxide layer off the metals, and also help the solder flow into the joint. No-clean flux is nice, but you can always clean it off with some rubbing alcohol to be safe.

If your iron has an adjustable temp, shoot for 300° C at minimum for leaded solder, I prefer 320° personally. Lead-free solder will need a higher temperature, but it's a moot point since you shouldn't ever bother with that stuff. If your iron isn't temperature controlled, make it a priority to replace it. The TS-100 is popular for good reason, but you can find a perfectly good adjustable iron for less than $30. I think. My last cheap iron was like 15 years ago. ¯\_(ツ)_/¯

Also, you might want to tape the motor wires to the arms so they can't find their way into the props.

I run this instead of a Dremel brand tool. I have had a couple Dremels die on me over the years, so I tried this one and it has lasted 4 years so far! I also got a lot of my bits from harbor freight. I use the cuttoff wheels (ALWAYS WEAR FACE PROTECTION WITH THESE), Sanding Drums, and grinding stones the most. Use the cutoff for cutting out large swaths of material, sanding drums for tighter areas, and grinding stones to debur and smooth it all out. Most work that needs a dremel can be done with hand tools for better control. Coping saw, files, and flush cutters can go a long way. A lot of the "pros" don't use Dremels because they can jump out of control and hit a part of the blaster you planned on leaving stock and leaving a huge gash.

As for soldering Irons, I've heard wonderful things about this model, but cheaper models will work fine. TBH, I'd grab something in the $10 range and see if he sticks with the hobby. Maybe for christmas you can get him a nicer one if he's still going at it. I use a super duper old school Weller soldering station, so really anything will work. The issue you'll get with the cheaper soldering irons is the tips will tend to not last long and the heating element might crap out after a few months. Don't go cheaper than $10 here as some of them are meant for wood engraving, not soldering and wont get hot enough to melt solder. Any size solder is fine. I personally use lead/tin solder and just avoid breathing fumes as well as wash my hands when I'm done modding. Lead solder is MUCH easier to work with and requires less heat. Look for "Rosin Core solder" as it's easier to work with as it has flux in the center of the solder.

Good flush cutters, hobby knife, wire strippers, heatshrink, wire, loctite, etc are all valuable modding supplies. We sell some on our shop (shameless plug). I would recommend for plastic to plastic bonds he use Devcon Plastic Welder (make sure it contains Methyl Methacrylate as this acts as a solvent weld to bond the plastics together chemically instead of a weak adhesive grip like putty). Putty should be used as a filler material. I use two different putties. Free form Air for large amounts of gap fill, it is 6 times less dense than normal putty so it wont make the blaster weight 8 pounds when done. It is VERY easy to sand, but sometimes requires a thin layer of bondo over top of it to leave a perfect finish. I also use Apoxie Sculpt which is a direct replacement for normal putty for gap filling purposes. It's MUCH easier to sand than JB Weld putty, and leaves a nice smooth finish when sanded down.

Speaking of sandpaper, get various grades of sandpaper from 100 down to 600 grit (I go as far as 1000 if I want a gloss sheen on something).

Other than all of that, the tools I have on my bench that I would hate to mod without now are: Helping hands (for soldering), various different sizes of needle nose pliers, numerous sizes of small to medium screwdrivers, silicone lubricant, hot glue (for securing wires inside the shell), Electric Screwdriver, and various tweezers.

> Weller WD1

Seriously? If you're going to be dropping $400+ on a soldering station, then you buy some quality HW. JBC > Weller in precision soldering equipment.

OP is looking for something like a TS-100, or a FX-888

OP can buy cheaper if they're not planning to get into the hobby, but I'd suggest investing in a station with adjustable heat as a minimum.

https://www.amazon.com/UY-CHAN-Programmable-Pocket-size-Acceleration/dp/B01MDTO6X7

Hey, best tip i can give you to get better is to find junk printers, motherboards, ect... and just practice de-soldering and re-soldering caps, resistors, anything that just has two pins. Also I would also suggest lowering the temp on the Iron (if you can) I use about 320 C for most of my stuff, and I would also recommend getting a good soldering iron it helps a lot. The soldering Iron I would recommend the TS100 with the D24-Tip, then look online for how to set it up.
If you like you can contact me by discord, and I can help you with what ever you need, (my discord Demi 소금#9026)

One last thing is that Twisting and pre-tinning the wires is almost a must when soldering anything.

Soldering Tip(D24-Tip) : https://www.amazon.com/gp/product/B06XYR3VTJ/ref=ox_sc_saved_title_7?smid=A2FGAWCX62OR7U&psc=1

Soldering Iron: https://www.amazon.com/NovelLife-Mini-TS100-Soldering-Digital/dp/B07D35B75T/ref=sr_1_2_sspa?crid=1PGZOPAOX1MUO&keywords=ts100+soldering+iron&qid=1557599888&s=gateway&sprefix=ts100%2Caps%2C148&sr=8-2-spons&psc=1

> I've also found an old laptop AC power adapter with a DC output of 19V at 3.0 amp.

What you have there is an excellent match for a TS100 soldering pencil.

20V is a negligible shock hazard. But at 3A it's enough power to heat up and sometimes even explode components that are connected wrong. So use eye protection and beware of possible hot components and you should be fine.

I personally think you should've gone for one of these. A much better experience and a better price, I use it for everything and is super convenient because of how small it is.

Opinions on these three soldering irons? It's only use will be for keyboards, and I don't anticipate building them as often as we all dream, haha. But I do want one that'll do the job well without going over the $100 mark, and preferably under $80 if any of these are decent.

Hakko Dial type temperature limiting soldering iron FX600 https://www.amazon.com/dp/B006MQD7M4/ref=cm_sw_r_cp_api_pBXMAb3DXH857

Hakko FX601-02 Adjustable Temperature Controlled Soldering Iron, 67 Watts https://www.amazon.com/dp/B00FZPSX3G/ref=cm_sw_r_cp_api_UDXMAbYNHEAWS

UY CHAN Upgraded Original TS100 Digital OLED Programmable Pocket-size Smart Mini Outdoor Portable Soldering Iron Station Kit Embedded Interface DC5525 Acceleration Sensors STM32 Chip Fast Heat (B2) https://www.amazon.com/dp/B01MDTO6X7/ref=cm_sw_r_cp_api_CEXMAb7A2CDNW

The counterfeit isn't a bad counterfeit, some people even like it more than the original. If you can get it for significantly cheaper then go for it, just don't buy it for anywhere near the price of a non counterfeit item.

There is another one you can get for about 60% of the cost called the TS100, it's a pretty quality iron https://www.amazon.com/Programmable-Pocket-size-Soldering-Interface-Acceleration/dp/B01MDTO6X7/

Build Your Own Clone

I doubt you'd keep track of any more websites I could mention above once you find a few kits there. As far as equipment goes, get:

A decent soldering iron ... Alternative (please also get this with the alternative)

Solder

Micro Cutters to trim leads

Hopefully you have a small flat-head screwdriver to set knobs and a small flat pair of pliers to attach hardware to the enclosures.

I doubt you'd need to but if you ever need to get any components that aren't supplied with a kit, go to Tayda Electronics for nearly any part (they tend to be cheapest for hobbyists, you can find anything from passive components like resistors and capacitors, to knobs/switches/audio and power jacks, etc.).

Don't use lead free solder, ever. Use rosin core, use a good solding iron.

Good solder
https://www.amazon.com/dp/B00DKF13JY/ref=cm_sw_r_cp_apa_KQKdAb2SRMP17

Good soldering iron
https://www.amazon.com/dp/B01MDTO6X7/ref=cm_sw_r_cp_apa_8TKdAbNTRP60A