Reddit Reddit reviews White SiliconeTubing, 1/4"ID, 3/8"OD, 1/16" Wall, 10' Length

We found 4 Reddit comments about White SiliconeTubing, 1/4"ID, 3/8"OD, 1/16" Wall, 10' Length. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Industrial Plastic Tubing
Industrial Tubing
Hydraulics, Pneumatics & Plumbing
Tubing, Pipe, and Hose
White SiliconeTubing, 1/4
Flexible tubing for air, water, food, and beverageSilicone rubber for resistance to high temperatures, oils, detergents, ozone, and salt waterTranslucent for visual inspection of fluidsOperating temperature range of -150 to +500 degrees FMeets NSF-51 standards for food equipment material
Check price on Amazon

4 Reddit comments about White SiliconeTubing, 1/4"ID, 3/8"OD, 1/16" Wall, 10' Length:

u/wtf-m8 · 3 pointsr/Waxpen

read my other reply re: health risks and why I'd personally rather not risk it.

this is the tubing I use.

u/iloling · 3 pointsr/trees

Hey, just a friendly heads up you may wanna switch to food grade silicon tubing instead of vinyl (as that appears to me). I had once used a vinyl tubing until I read that when heated it releases chemicals that when inhaled can be extremely detrimental to the lungs over time. Not the worst thing once in a while I'm sure, but the food grade tubing will accomplish the same task as other tubes without the negative side effects. It's also a bit more flexible so it's easier to maneuver after a few rips! Looks AMAZING otherwise! Be safe and enjoy (:

Edit: here's the link to the one I used! It also fits around the glass stem of a MLFB perfectly so you can "Vong" (vape/bong!) if you have one (: sorry for the long link, I'm on mobile: https://www.amazon.com/gp/aw/d/B000FOWGG2/ref=ya_aw_od_pi?ie=UTF8&psc=1

u/Brutal_Peacemaker · 1 pointr/vaporents

1-Get yourself a grinder, got one? Go to 2
2- Grind a quantity of your stash (drier is always better), ground? Go to 3
3- Turn it on,I prefer 165°C for an energetic buzz, 200°C for a body high (results may vary)
4- Using the whip? Go to 5. Bagging it? Go to 8

5- Elbow pack that bad boy. Google elbow packing extreme Q or https://www.youtube.com/watch?v=07mIhuyDdTY&feature=youtube_gdata_player go to 5
6- Place elbow on cyclone bowl, let it heat for 2 minutes
7- Two deep breaths, one slow DEEP pull, hold it in for 5-10 sec

8- Fill your cyclone bowl loosely, no higher than the bottom of the black heat guard on the bowl
9- Assemble cyclone bowl + elbow + bag
10- Let it heat up for 5 minutes
11- Turn fan on 2. You should be able to see your hand through the bag's vapors. Thick vapors? Fan on 3, Thin vapors? Fan on 1

12- enjoy

P.S. You should look into changing your plastic tubes for this: http://www.amazon.com/dp/B000FOWGG2/ref=biss_dp_t_asn or something alike (I did and it is worth it). Non-toxic, heat resistant and can be cleaned with iso-alcool
P.P.S Also look into purchasing a straight glass reducer (standard 14.4mm labware reducer I think) instead of the elbow, reduced restriction = easier draw and faster bag fill

u/pricelessbrew · 1 pointr/Homebrewing

Obviously way more than you need, but here's 10' 1/4ID 3/8 OD for $9.

https://www.amazon.com/dp/B000FOWGG2/ref=biss_dp_t_asn