Reddit Reddit reviews Wonder Wedge Cosmetic Wedge 100's

We found 5 Reddit comments about Wonder Wedge Cosmetic Wedge 100's. Here are the top ones, ranked by their Reddit score.

Beauty
Makeup Brushes & Tools
Makeup Blenders & Sponges
Tools & Accessories
Face Makeup Brushes & Tools
Wonder Wedge Cosmetic Wedge 100's
100% Latex-Free Synthetic FormulaBiodegradable And Anti-BacterialNaturally Hypoallergenic
Check price on Amazon

5 Reddit comments about Wonder Wedge Cosmetic Wedge 100's:

u/ThisIsWhyICarry · 156 pointsr/guns

Good guide. Especially the method of drying. ;-)

That said, I recommend against nail polish and nail polish remover; polish doesn't set as well as enamel paint, and thus, it won't last as long or look as nice. One factor to this is that enamel paint settles flat better than nail polish does - the latter tends to curve inward or bulge outward, depending on exactly how much there is, whereas enamel paint can be polished off relatively even to the gun surface. Here's a comparison, with nail polish on the left and enamel paint on the right, and here's the final product. Note that this method also works on plastic; I filled the etching of the Crimson Trace laser as well.

Instead, I recommend Testor's 1168 Flat White enamel paint, which can be found at most hobby supply and arts & crafts stores. I apply with a very thin brush or with toothpicks, depending on how fine the work needs to be. I'll stick the tip directly into the etching grooves so that I don't end up with bubbles. I try to keep the coat relatively thin, but just thick enough so that I can't quite see the etching through the first coat when I'm done. (More on the second coat shortly.) Let it dry for an hour with a fan on it. You can sometimes get away with less time, or use a hair dryer to speed up the process, but I've found less than an hour (if you don't use a hair dryer) leaves the paint too tacky and more comes off than I'd like.

To clean up the excess paint, don't use paint thinner - not even Testors. Paint thinner will, well, make the paint too thin. This makes it too easy to accidentally remove paint from the etching that you want to leave behind. Instead, I use Hoppe's No. 9 Bore Solvent. It works similarly to paint thinner but isn't quite as powerful, which means it doesn't thin the paint as much. It's also a useful gun cleaner, so it's handy to have around anyway. :-)

Use a combination of cotton rounds and makeup sponge wedges, both of which can be found in the make-up section in most grocery stores or pharmacies for a few bucks per bag. The rounds are good for broad strokes to wipe away larger amounts of excess paint, and the wedges are good for detail work or to gently swipe evenly over the etching without pressing loose cotton threads into the etching. I try to do as few wipes over the actual etching as possible - the more you wipe the etching, the greater the chance you remove paint from inside the etching. Don't press hard, either; just press enough to maintain contact; let the solvent do the work for you.

Let the paint dry for another hour, and then apply a second coat. Odds are good that you've accidentally removed too much paint in some parts of the etching, especially where it's thin or has sharp corners. Then let dry for an hour, remove the excess with Hoppe's again, and let dry overnight to fully cure.

This will probably take you around a total of 3 hours to do, but it's worth the extra time - it looks beautiful and will last forever. Obviously, you'll need more beer for this method, but OP says you can get a 30-pack of Miller Lite for $18. It may suck, but after 30 of them, you probably won't care.

u/Lavarie · 4 pointsr/RedditLaqueristas
u/ZombieButch · 4 pointsr/learnart

If it's dry, you can just scrape it down with a palette knife or sand it down with some fine grit sandpaper. It doesn't have to be, like, smooth as glass or anything, you just want to avoid any big piles or little spikes of paint.

In the future, if you do your underpainting with pretty thin paint for your darks, you can wipe away the light areas with a rag or paper towel. If you're working in oil paint, cosmetic wedges are awesome, and tonking is a really useful technique for pulling up excess paint while it's still wet. (It may work on acrylics while they're wet, too; I don't really use them but unless there's some kind of extender in the medium I would think it'd dry too quickly.)

u/Lrs8855 · 3 pointsr/Warhammer40k

For the weathering, he uses quite a coarse sponge.

Personally, I prefer using: https://www.amazon.com/gp/product/B003BMGAFI/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1

Very even coverage for weathering effects, making them seem more genuine to me.

Cheers!

u/skelezombie · 3 pointsr/RandomActsOfPolish

Okay so there's lots of places you can get things, but with some of amazon you might not get things in time so keep your eyes peeled, I'm linking random ones for you. It'd be easier to build your own basket instead of trying to find one. What I would suggest is:

-dotting tools like this

-brushes for art/cleanup like this

-clear stamper/scraper like this

-some stamping plates like this

-liquid latex (so her fingers don't get messy when doing different nail art styles) like this

-makeup sponges (those triangles, for gradients) like this

-striping tape like this

-good base coat (people really like nail envy by OPI and ORLY bonder) OPI ORLY

-good top coat (Seche vite is great) like this


I didn't pay much attention to the prices but a lot of those tools can be purchased fairly cheap, the most expensive things are the polishes and some stamping plates (some are very cheap and can be not so good, some are more expensive but are more likely to work well)

If you need more help let me know!