Reddit reviews ZENY Pro 1/5 HP Airbrush Air Compressor Airbrushing Kit w/ 3L Tank and 6FT Hose Multipurpose for Spraying Cake Decorating Tattoo Nail Craft Painting

IWATA NEO CN airbrush and AS-186 compressor.

For a total of 140$ as the time of writing this (on 5.8.2019.) it is the best cheap airbrush and compressor combo.

Why? You get the whole package - Airbrush, a compressor with a tank, air filter and a hose which is all you need to start airbrushing


Iwata Neo is considered the best cheap(est) branded airbrush on the market by many so I used it here, also the AS-186 compressor (Check later in the page about it more) is p good. You also get a hose which far too many people forget to buy when choosing a compressor.


mostly everything


-----


Note for other users - I am currently rewriting the airbrush page a bit (this will be on the top of the page), so if you have any wishes to add to it please comment.

Save your money. You need $20 more for a decent starter brush here, I wouldn’t buy one of these, I had one, made one model and sold it. In honesty I’d save up, double your money and buy either a kit like this compressor with tank with brush, or preferably just the compressor for $70 and a decent airbrush like the Iwata neo for $60.

A compressor with a tank means the compressor doesn’t run all the time so prolongs the compressor life itself. It has a decent water trap and regulator to adjust pressure.

A Neo is a superb brush for the money, cheap Chinese airbrushes have less accuracy, require deeper cleaner and can give a frustrating experience.

It’s often worth spending once and spending right in this field. Hence I suggest saving your money.

You can get a tankless one .

It runs near constantly and can heat up. They are not ideal, but can do the trick for small jobs. I tend to work on my models for an entire day once a week, so I have one with a 3L tank.

If you got the super cheapie one there for $60 you could get the Badger 105 and you would probably have a little bit left over.

There is also this one. It is cheaper, so I really can’t speak to it’s quality.

thats a great starter airbrush and should be perfect as a workhorse.

you just need a basic airbrush compressor to start with. the cost goes up the more quiet the compressor is while building up pressure.

i use this kit https://www.amazon.com/ZENY-Airbrush-Compressor-Multipurpose-Tattoo/dp/B01M33C8MV/ref=sr_1_20?s=arts-crafts&ie=UTF8&qid=1526986007&sr=1-20&keywords=airbrush+compressor

the hose it comes with should work with the neo.

The problem with that kind of compressors are that they don't give out a stable amount of air. That means it may start spitting paint instead of giving a nice constant flow of air/paint.
You're going to get all sorts of opinions. Ones will say they work well, some others (like me), would recommend something with an air tank.
https://www.amazon.com/Zeny-Airbrush-Compressor-Regulator-Filter/dp/B01M33C8MV/ref=sr_1_2?ie=UTF8&qid=1482100140&sr=8-2&keywords=airbrush+compressor+with+tank

Something like that will do the work, it will last you very long if treated correctly and in the long run will save you some money. If you buy the cheap one, even if you only use it for priming and base coating, you will want to get a better one very soon.

In the end, the choice is yours, of course :)

https://www.amazon.com/dp/B01M33C8MV/ :-)

For your budget I'll go with a Badger Patriot 105 Arrow, it's so easy to use and clean and the Arrow will give you a fine line if needed. A cheap compressor with a tank and a quick connect and you're good to go !

Badger Patriot Arrow : https://www.amazon.com/Badger-Air-Brush-Co-105-2XR-Airbrush/dp/B00471RFQA/ref=mp_s_a_1_5?keywords=badger+patriot+105&qid=1567304916&s=gateway&sprefix=badger+pa&sr=8-5

Quick connect Badger for all hose : https://www.amazon.com/Badger-Air-Brush-Co-51-038-Disconnect/dp/B000BPOJCO/ref=mp_s_a_1_3?keywords=badger+quick+connect&qid=1567305182&s=gateway&sprefix=badger+qui&sr=8-3

Cheap Compressor : https://www.amazon.com/ZENY-Airbrush-Compressor-Airbrushing-Multipurpose/dp/B01M33C8MV/ref=mp_s_a_1_3?keywords=airbrush+compressor+with+tank&qid=1567305014&s=gateway&sprefix=airbrush+compressor+&sr=8-3

With airbrush cleaner and thinner, and a cleaner pot, I think I fit your budget.... You can use the standard Badger Patriot 105 but the needle is .75mm instead of .5mm so you get less fines lines

Without knowing the condition of the brushes/compressor, you can get a new compressor and brush for about the same price. Honestly starting out it would probably be more confusing to have all those brushes at your disposal instead of becoming proficient with one.

​

Compressor with tank - $70

Badger 105 brush - - $78

Cleaning kit - $14

Total new (minus tax) - $162

That unit will work, but a bunch of manufacturers make near-identical compressors and some are cheaper, like this one.

​

Some reviews note poor quality on the fitting between the air tank and the water trap/regulator assembly, but that hasn't been my experience. Maybe quality control has improved since those reviews, or maybe I just got lucky. Your mileage may very.

I use an Iwata Eclipse HP-CS (the gravity feed one, and not the CN knockoff) and it works pretty good. My nozzle clogs up every now and again if I've got my thinning slightly off but otherwise, no major problems yet. I ended up picking up the compressor that was discussed here on the wiki and it works pretty well so far, and it's quiet enough that you can't hear it in the room next door. I live in a townhouse so that was really important for me. As with anything though, see what works for you and read reviews. This Amazon link is the exact one that I bought (and according to honey, its about 30% now than it was a month ago, so good time to buy lol).

https://www.amazon.com/gp/aw/d/B01M33C8MV/ref=mp_s_a_1_13?ie=UTF8&qid=1501114047&sr=8-13&pi=AC_SX236_SY340_FMwebp_QL65&keywords=airbrush+compressor

Couldn't be happier.

ZENY Pro 1/5 HP Airbrush Air... https://www.amazon.com/dp/B01M33C8MV?ref=ppx_pop_mob_ap_share

A lot of airbrush compressors you will find are the same Chinese model that has been rebranded. You won't notice any difference in the amount of air pumped or volume it holds so your best bet is to go with the cheapest option on the market.

https://www.amazon.com/ZENY-Multi-purpose-Airbrushing-Compressor-System/dp/B01M33C8MV/

Thanks! can you tell from the look if this compressor will fit with the eclipse; or what I should be looking for to determine compatibility? $65

I bought this air compressor for airbrushing model kits. I was wondering if I could also use it to dust out my PC. It comes with a moisture trap, but I'm not exactly sure how to deliver the air.

My first thought would be to just use my airbrush, assuming it's completely dry (I can run IPA through it to ensure it's dry) and letting the PC dry overnight (just for added safety), would this be a good idea? Or should I buy a cheap airgun instead?

Would This be a good compressor

I think I decided to bite the bullet and just get an airbrush. Here is the setup I was looking at:

Airbrush: https://www.amazon.com/Badger-Air-Brush-Patriot-Gravity-Airbrush/dp/B002W84GTO

Compressor: https://www.amazon.com/ZENY-Airbrush-Compressor-Multipurpose-Tattoo/dp/B01M33C8MV

Just wondering what your thoughts are on this combo and if I need any other adapters/hoses/etc or if these two items will cover it. Also in regards to thinning the Mr. Color paints for the airbrush, what ratio of paint/thinner/leveling thinner should I mix at? (I am in a hot and dry climate)

I was thinking something along these lines:

ZENY Pro 1/5 HP Airbrush Air Compressor Airbrushing Kit w/ 3L Tank and 6FT Hose Multipurpose for Hobby Paint Cake Tattoo Nail https://www.amazon.com/dp/B01M33C8MV/ref=cm_sw_r_cp_api_i_KP4sDb35QGMKY

Not sure what you could do to make it quieter. Maybe sit it on a towel to absorb some of the vibration or something like that?

This have a tank this dont No tank, its a tank that storage ari so when you are spriying isn't always on. If he doesn't have a tank its always taking air and doing noise and also it hots faster.