Best automotive headlight parts & accessories according to redditors

We found 370 Reddit comments discussing the best automotive headlight parts & accessories. We ranked the 42 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Subcategories:

Automotive headlight adjusting screws
Automotive headlight bulb retainers
Automotive headlight wiring kits
Automotive headlight restoration kits
Automotive headlight covers

Top Reddit comments about Automotive Headlight Parts & Accessories:

u/br0sidan · 182 pointsr/subaru

Here's what I did:

  1. Watch this YouTube video
  2. Buy a kit with the stuff he uses. (I bought this kit by Meguiars)
  3. Follow the instructions carefully and watch the video.

    If you're patient and careful, it'll turn out great.
u/Trisomic · 145 pointsr/DIY

Total cost: $31.70

Time: ~30 minutes.
Tools required: Hand drill

Now that it gets dark so damn early, I've been using my headlights a lot more, and I noticed that they weren't as bright as they used to be. So, on the advice of a coworker, I picked up THIS headlight restoration kit from amazon, as well as THIS sealer and THIS masking tape (to protect the paint around the lens). The directions were clear and concise and the whole process took about 30 minutes and was extremely easy. It comes with an attachment for your hand drill to which a variety of sanding/buffing discs mount. You start with a coarse grit sandpaper disc to remove the oxidation and then you use progressively finer grit discs to smooth out the surface. Finally you buff and seal the lens.

I couldn't be happier with the results. The lenses look brand new and there are enough sanding discs left over to do at least one or two more cars.

u/FlickeringLCD · 32 pointsr/LifeProTips

Toothpaste has abrasive qualities which lends it to secondary uses as a polishing compound. They sell commercial kits that do similar things. It'd probably take half a tube of toothpaste, and a lot of elbow grease to get these results.

u/spike_africa · 30 pointsr/Cartalk

This seems like an obvious answer.

But it's because one headlight is much newer then the other. The old one is fogged over from sun damage and need to be sanded and buffed.

Use this kit with a home power drill to make it like new. I'd suggest going over the other one too a bit just to make them both match.
https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

u/GonadsOfWrath · 19 pointsr/AutoDetailing

> it will be driven 25k per years, so road wear and tear may be more significant than UV in this case.

No, road wear and tear is barely a factor. UV and heat/IR exposure are by and far the biggest factors in lens deterioration.

>I've done a decent bit of reading on here and recently tried Meguiar's Keep Clear (https://www.amazon.com/Meguiars-G17804-Clear-Headlight-Coating/dp/B01M4RVVX6/). However, I thought it gave a bit of a cloudy appearance, so I removed it with isopropyl alcohol. After removing it, I realized it might just be that the headlights have a slight cloudy appearance when viewed from really oblique angles with the lights on.

Right, don't fix what aint broke. The only thing that product is good for is:

a) keeping your wallet from getting too heavy

b) temporarily protecting severely degraded headlamps that have been restored

>I don't really want to go the Opti-Lens route, as I'm worried I would make a mistake and it can only be removed with abrasives. Some options I'm considering:

Opti-Lens is the same deal: it's something you don't use until you have no other choice, no matter how much the guy who made it tries to convince you to buy it and help his bank account.

>I recently bought a 2019 Forester, and the difference between the LEDs and the halogens on my old car are significant. I want to try to keep the headlights looking as new as possible.

You have LEDs. They run cool. The lens will appreciate that significantly. Your main enemy is UV exposure, not road salt/grime/debris. Just wipe off the headlamps with a gentle solution of soap and water every now and then if you are so concerned about road debris. Maybe stick with the no-solvent routes like Optimum No-Rinse instead of using something like a spray wash+wax, since waxes are usually carried in an organic solvent.

UV exposure is by and far the #1 enemy, but in your case, since you have LEDs, it won't be as bad as UV + IR from hot-running halogen bulbs. To combat UV exposure, I would:

a) Park in the shade whenever possible

b) You said it will be parked outside 24/7, so look into maybe a removable set of headlamp covers (keyword: removable) or consider covering them with a damp microfiber cloth whenever possible. A damp cloth will tend to stick to the car and not get blown away like a dry cloth, and it will block UV, and whenever you're ready to drive they are easily removed. Covers should be removed each time you go driving.

>Simple car wax every few weeks.

This probably won't hurt, but I wouldn't overdo the waxing. Waxes contain hydrocarbon solvents, and although the polycarbonate hardcoats are tested against common hydrocarbon solvents (gasoline) I wouldn't want to you know, test the limits of durability.

>Nothing, and do a real restore in 3-4 years.

More like do a real restore in 6-7+ years. Like I said, there's not much to worry about with all-LED headlamps. They run cool, so you've removed IR degradation from the equation. UV remains a killer.

u/nknasi · 13 pointsr/Lexus

I used the Mothers NuLens kit which has everything you need except for the drill. Comes with the drill chuck attachment, 800/1500/3000 grit sandpaper attachments as well as the polishing ball and the plastic polish. I took my time, and it took about an hour per light. Well worth the $20 and 2 hours of my time, imo!

u/zenautodetailing · 11 pointsr/AutoDetailing

They are not dirty but oxidized. Look into a headlight restoration kit. I recommend this 3M kit. You will need a drill.

u/adamskee · 11 pointsr/LandRover

Used https://www.amazon.com/Meguiars-Two-Step-Headlight-Restoration/dp/B01M75GUJB . Was super easy and there is enough in the kit to do another 2 full cars.

u/nahman3m · 9 pointsr/Justrolledintotheshop

Nah man just get that 3M kit for 20 bucks. Cleaned up my headlights like new and it has a protection wax so the issue hopefully doesn't reoccur for a while. You get a polishing drill bit too so no elbow grease required. I believe there are three different grits of sandpaper used and a sealing compound at the end. (including the MAGIC trizack disc!) its a wet sand.

https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY


theres enough stuff in that kit to do at least 2 cars.

the most time consuming part is taping off the lights so that you dont scratch the paint with the sandpaper.

u/pbs094 · 9 pointsr/AutoDetailing

The "fog" on the other light is really the plastic breaking down from years of exposure to UV rays after the clear coat wore off. It's actually quite easy to restore headlights with a kit like this. Do a search for headlight on this sub and you can see some pretty spectacular before and after pics. Good luck!

Edit: Forgot to mention...after you restore the headlights you should seal them or else they will just get yellowed again.

u/TheGhettoPanda · 9 pointsr/mercedes_benz

Headlight Polish I have a 2001 E320 and the difference is night and day.

u/Lobotomite430 · 8 pointsr/Lexus

3M 39008 Headlight Lens Restoration System https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_cp_apa_Uwt2Ab1G3S8SB

I've personally used this kit on a dozen headlights and love the results.

u/brock_lee · 8 pointsr/cars

I got the Turtle Wax one, and it works surprisingly well.

http://www.amazon.com/Turtle-Wax-T-240KT-Headlight-Restorer/dp/B001TI5IIQ/ref=sr_1_1?s=automotive&ie=UTF8&qid=1396157068&sr=1-1&keywords=turtlewax+headline

However, I would also suggest getting one you use a drill with for the buffing. The one I used was great, but my arms were tired afterwards.

u/ekib · 8 pointsr/cars

Just stick with halogens. Sylvania Silverstar Ultra bulbs are bright as hell. Should be able to get them on Amazon or at any auto parts store.

But more importantly, are your head light lenses all cloudy and yellow? Because that dims the light output a lot. You can polish them yourself with a kit like this (https://www.amazon.com/dp/B00429NKWK), or any body shop should be able to do it for you.

u/ketsujin · 8 pointsr/cars
u/homerpalooza101 · 8 pointsr/cars

Picking up one of these kits was easily worth the money. My headlights were completely fogged over, so I used the toothpaste trick. Cleared it up a fair amount, but it was back to bad in about a month. Used that kit, took about an hour and some elbow grease, and they looked literally brand new when I was finished. 7 months later, they still look absolutely great.

u/chinslapped · 8 pointsr/hondafit

Meguiar's G2970 Meguiar's Two Step Headlight Restoration Kit, 4 fl. oz, 1 Pack https://www.amazon.com/dp/B01M75GUJB/ref=cm_sw_r_cp_api_i_QIXxCb7TR1Q1R

This kit works well. I did two cars with it that were pretty bad.

u/motoo344 · 6 pointsr/AutoDetailing

You did half of the work required to get your desired results. In order to remove the 2000 grit sanding marks you need to polish them out. You are basically using a liquid that has abrasives in it, think of it as liquid sand paper. You put some compound on the orange foam pad and then polish it out with a machine polisher. Like sandpaper, compound leaves scratches, although they are very fine. You need to use a less abrasive polish on a less abrasive pad, the white one. This brings back the clarity and then you can clear coat them. You can keep it simple and buy something like this which will attach to a power drill. https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_1?ie=UTF8&qid=1478747348&sr=8-1&keywords=3m+headlight+polishing+kit

u/Crack_a_toe_a · 5 pointsr/NewOrleans
u/Travels4Work · 5 pointsr/Jeep

Very nice.
This will make the headlights look brand new if you take about 30-45 minutes on each one, and you'll get a lot more light out of them as well. See videos on youtube showing how-tos.

u/imakeyourday · 5 pointsr/vegaslocals

I just did my headlight myself using a kit I got off Amazon. Worked amazing. Took me 1 hour.

Here is the kit if you are interested.

SYLVANIA - Headlight Restoration Kit - 3 Easy Steps https://www.amazon.com/dp/B00429NKWK/ref=cm_sw_r_cp_apa_i_k2CGDb2C87APJ

Edit: $20 bucks for this kit.

u/Highfive_Machine · 5 pointsr/LifeProTips
u/accordingtoben · 5 pointsr/Honda
u/bob_smithey · 5 pointsr/hondafit

Well, you have two options. You can buff the head lights clear. Either with sand paper or aluminum polish and a buffer. Then you'll have to reseal. What I used and it worked great. But only after you've buffed. Most of the kits are gonna be the same. Just make sure they have a sealant afterwards, or it'll be hazy in weeks.


Or, you can dab a little ATF (automatic transmission fluid) every few weeks and it'll be clear-ish. Just make sure you don't get any of that stuff on your paint.


I think this sort of damage is from those automatic car washes. Didn't have a problem, for years, until I started going to one for a bit.

u/zerostyle · 5 pointsr/personalfinance

Have you done the previous maintenance intervals? i.e. fluid flushes (transmission, coolant, brake fluid, spark plugs)? Recommend using DOT 5.1 brake fluid, and long life coolant/trans fluid.

Not sure on the civic, but if it uses a timing chain (which it probably does) it's probably due for an adjustment. If it uses a belt you need to change that ASAP. Honda lists their belt replacement at 7 years or 110k miles, whichever comes first.

Might be a good time to replace the battery before it leaves you stranded.

For other minor things, I would:

u/squisheystick · 4 pointsr/subaru

if you have a power drill, get the 3m restoration kit. it looks like this.

http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_1?ie=UTF8&qid=1396424163&sr=8-1&keywords=3m+restoration+headlight+kit

i mean you dont have to have a drill, but it would make it easier.

this is what mine looks like before and after. haha
http://i.imgur.com/R78vYXY.jpg

u/trainspotting2 · 4 pointsr/Volkswagen

Kinda. Not really. You're better off spending the $13 on a restoration kit.

u/jeffj95 · 4 pointsr/Lexus

This seems like a decent product.

u/Seeker80 · 4 pointsr/cars

You can either try a a restoration kit, or spend more on all-new lenses.

It depends on how much of a $/improvement ratio you're looking for.

u/nalydnalydnalyd · 4 pointsr/jetta

https://www.amazon.com/Meguiars-G17216-Ultimate-Compound-15-2/dp/B001O7PNNM

it’s essentially a micro abrasive compound, which is used to buff out scratches, hazing and whatnot. it needs to be used after wet sanding to get rid of the hazing left behind from the 3000 grit. then you polish after the compound to get an extremely clean, haze-free result. it’s best to use a buffer to apply them but can also be done by simply rubbing with a microfiber pad.

basically you can get all of these products in a simple 3m headlight restoration kit instead of buying a bigger amounts of each separately. if you only need to hit the two spots left from removing your mudguards, i’d suggest just getting a kit instead:

https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

u/a6mzero · 4 pointsr/Shitty_Car_Mods

I was gonna say this but that works too

u/Banana4scales · 4 pointsr/AutoDetailing

Buy one of these. I used it on my headlights and they came out looking band new.

u/ohshititsdatboiii · 4 pointsr/saab
u/ProfessorLX · 4 pointsr/Acura

I bought the Mother’s kit and use it once a year. Someone in here said polishing only lasts about 6 months and they are basically right so I do it in late spring generally and it’s good until the end of summer.

The Mothers kit is nice, it has a pad for polishing with a bottle of polish liquid, also some various sanding pads if it’s really bad. I tried doing the sanding one year but honestly just the pad did just as good a job.

Mothers 37251 37251 NuLens Headlight Renewal Kit

Make sure you cover everything around the area because even if you are careful polish will fly off and leave little drips here and there

u/tafunast · 4 pointsr/subaru

Got this one. Totally recommend.

u/illestvillains · 4 pointsr/e39

Polishing them will last much longer if you use a UV resistant spray on the lenses after you polish.
Example: https://www.amazon.com/dp/B01M4RVVX6/ref=cm_sw_r_cp_apa_i_YlDzCbADQWCG5

u/fckimlost · 4 pointsr/WRX

C Light - https://www.diodedynamics.com/2015-2019-subaru-wrx-sti-c-light-switchback-led-halos.html

Halos - https://www.diodedynamics.com/hd-led-halos-for-2015-2019-subaru-wrx-wrx-sti-pair.html

Blinker Module - https://www.diodedynamics.com/led-flasher-for-2015-2019-subaru-wrx.html (Needed this because I removed my stock blinker lights. Could have wired in resistors, but this was easy and cheap)

LED Conversion Bulbs - https://www.diodedynamics.com/low-beam-led-headlight-for-2015-2019-subaru-wrx.html (Still waiting on these, so haven't tested them, but they'll be in this Friday)

Headlight Sealant - https://www.amazon.com/RetroRubber-Grade-Butyl-Headlight-Sealant/dp/B01N5PM29J

Harnesses to clean up wiring - https://www.amazon.com/gp/product/B07QFW8X9Z/ref=ppx_yo_dt_b_asin_image_o00_s00?ie=UTF8&psc=1 (Haven't installed yet, but planning on tomorrow)

Used to seal the hole of the old C Light bulb. Ran the C Light and Halo Harness through here - https://www.homedepot.com/p/Permatex-3-oz-Black-Silicone-Adhesive-Sealant-75150/302775053

Used to hold Halo in - https://www.homedepot.com/p/J-B-Weld-0-47-oz-ClearWeld-50114H/303710929 (There's other ways to do this, but this is what I chose)

Paint I used - https://www.homedepot.com/p/Rust-Oleum-Painter-s-Touch-2X-15-oz-Flat-Black-General-Purpose-Spray-Paint-25-Bonus-336099/304221900

I also got the Subispeed harnesses, but I didn't use them because I deleted the stock turn signal bulb.

​

And I think that's it. Be sure to wear nitrile gloves too to avoid finger prints.

​

Also take your time. Don't paint the high beam housing unless you have another plan for those like a second projector.

​

Any other questions or pictures let me know.

​

(Side note, this is probably not done for me and I'll probably post more if I do more with these. Thinking about changing the bumper cover holes where the turn signals were for instance)

u/pet_the_puppy · 3 pointsr/cars

http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_1?ie=UTF8&qid=1410403758&sr=8-1&keywords=3m+headlight+restoration+kit

3Ms kit is amazing. It works wonders. The one "with protectant" isn't worth the $10 premium, they just include a packet of wax that you might as well just buy a whole bottle of separately.

u/NewbieTwo · 3 pointsr/Miata

If you're talking about the headlights, the 3M Headlight Restoration Kit works wonders and has never failed me.

u/tampon_whistle · 3 pointsr/scion

http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

this is a great kit, used it on my truck and my brothers corolla

u/JaredTizzle · 3 pointsr/BMW

Restored my headlights about 6 months ago using this 3M Headlight Restoration System (Works GREAT)

These Predator Orion V2 LED Angel Eyes w/ Remote angel eyes from umnitza (Would NOT recommend them! However the angel eyes are awesome)

Clear Corners (Clean fit and no problems)

Stealth Bulbs (A big pricey however they look AMAZING)

Have clear side signals on the way, along with some Langka blob removal for some touchups.

u/nycska · 3 pointsr/Integra

The quickest and easiest temporary solution is to grab some Plast-X from a local auto store. Rub it in and wipe it off with a microfiber. It will help, but they won't look new and it won't last very long.

The more permanent solution is to sand the lights, 500 then 800,1500,2000,3000 etc. Then compound and polish with Meguiar's 105/205 or similar. Then you'll have to apply sealant (not wax, but something like Meguiar's M21) to protect from UV rays. This will bring them closer to new than any other method or product. If the lens isn't cracked and you spend enough time on each sanding step, they'll be near perfect.

3M also makes a nice little kit for a drill that you can find on amazon. If you don't already have a DA polisher, the kit is the way to go. It comes with an aggressive little pad, sanding discs, and polish. I found that 105/205 worked better than the single stage 3M polish, but it did work. The kit is nice as well because the orange polish pad it comes with is reusable, and with the right products (105/205) can be great for spot corrections on little scratches and swirls in the paint.

If you choose to sand, consider pulling the bumper off first. Our lights are tough because they are sunk in there so deeply.

u/Onlinealias · 3 pointsr/cars

Go get this. Use as directed and your headlights will be as clear and shiny as new.

BTW, don't get any other brand. I've used them and they all pretty much suck. The 3m stuff I linked to is like freekin magic.

u/hansmoman · 3 pointsr/GolfGTI

If the exterior surface has become yellowed or foggy, forget the toothpaste. High grit sandpaper (600,1000,1500) + polish. There are many premade kits available such as the ubiquitous 3M headlight restoration kit. There is another version that you can use that's done by hand if you don't have a drill, or you can just buy the sandpaper and polish separately. The process & products are the same as for polishing paint.

Edit: Here is a video showing how it works: https://www.youtube.com/watch?v=sA_MzKwU-lI

u/epyon22 · 3 pointsr/subaru

I used the 3m kit. Works really well, it's fairly involved but is the correct way to do it. You also will have to put some sealant or cover on it to prevent it happening again. I got the xpel kit. Ammonyc has a good guide.



XPEL H3804C Clear Headlamp and Fog Lamp Protection Kit https://www.amazon.com/dp/B0007X7R9C/ref=cm_sw_r_cp_apa_C47uzb6FAQ6TH

3M 39008 Headlight Lens Restoration System https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_cp_apa_j07uzbTH2YH63

https://youtu.be/uqOKmZ9mMfc

u/asterysk · 3 pointsr/Cartalk

I actually restored my headlights on my own not too long a go. After reading reviews for several online, I decided on 3M's. Benefit to the 3M kit is you don't kill your wrist since you're doing all the sanding with a drill instead of by hand. Just be sure to apply the tape (not included) LIBERALLY, especially around sharp corners so you don't scratch your paint.

u/Quravin · 3 pointsr/oddlysatisfying

3M's headlight cleaner on Amazon.

All you need is a regular ol' drill.

u/bmac92 · 3 pointsr/Miata

I used this 3M kit to restore them (which I bought when it jumped to $15 for 2 days instead of the average $10 :/) and Meguiar's Keep Clear coating.

If I had to do it again, I'd probably go with this Meguiar's kit that includes the keep clear. I say this because my wireless drill cannot hold a charge and to do both headlights it took me a long time.

u/geekywalrus · 3 pointsr/GrandCherokee

I used this 3M kit on my WJ when I still had it, and it came out looking fantastic. If I spent a little more time and was less nervous on doing it, they would have been 100% clear, but they were probably 90% there anyway. Here's a comparison!

I know it's a little hard to tell, but the headlight on the left of the picture was done with the kit, and the other hadn't been done yet. It definitely was a big difference (for both appearance and brightness during night driving) and I'd recommend using it if you have the time, patience, and cordless drill for it!

u/theseareyourpants · 3 pointsr/BMWE36

The yellowing was pretty significant so I decided to go with a kit with the sanding attachments to get it clear again: 3M Restoration Kit

Took roughly an hour once i had the headlights out, its super straight forward and all you'll need is a drill. The ones with the wipes or sandpaper sheets were priced the same at the auto part stores around me but decided to go with that one(~$10-20).

u/crackadeluxe · 3 pointsr/howto

Amen, although there are cheaper and better kits IMO.

u/ChrisW41182 · 3 pointsr/BmwTech

I'm with /u/pina_koala on this. It looks like surface damage of some sort. You could try this. It's pretty cheap and easy to try it out. It is also available at most part stores.

u/ironsights · 3 pointsr/350z

SYLVANIA Headlight Restoration Kit https://www.amazon.com/dp/B00429NKWK/ref=cm_sw_r_cp_apa_qg7.zb7PTYDE7


Just used this kit with great results. Just follow the instructions or the video on YouTube.

https://m.imgur.com/a/Obj3N

u/rugger62 · 3 pointsr/howto

You can use baking soda toothpaste and polish them, or just buy a polish kit made especially for this purpose.

u/2004r32 · 3 pointsr/GolfGTI

I have an 2004 R32 and did the same thing on my headlights last year.

I used this kit: https://www.amazon.com/gp/product/B00429NKWK (Sylvania Headlight Restoration Kit) which was pretty inexpensive ($17 USD)

I spent about an hour on the restore total and was skeptical until I applied the clear coat. Both sides came out near perfect.

Before: http://i.imgur.com/73bGThr.jpg
After: http://i.imgur.com/7oeujnP.jpg

Didn't get before/after pics of the same headlight but they were both similarly rough shape prior. Made it through the winter and still are looking/feeling really clear/smooth.

u/taiwanesekid05 · 3 pointsr/Honda

I've heard that 3M's kit works pretty well. You'll want the one with the protectant otherwise you'll find yourself with foggy lights after a few weeks. I haven't tried the kit myself but others online and on r/autodetailing seem to like it.

u/orlheadlights · 3 pointsr/AutoDetailing

Also, take a look at restoring your headlights. It will make them look new again instead of yellow and oxidized.

For an over the counter solution, the 3M 39045 Headlight Renewal Kit with Protectant (drill version) is my most recommended solution. It comes with a sealant but remember it will need to be re-applied to prevent oxidation from coming back.

I would suggest you reapply a sealant or wax to your headlights every time you wax/sealant your car.

u/mrdotkom · 3 pointsr/cars

Toothpaste if you feel like spending almost nothing, but unless you apply a protectant it'll oxidize pretty quickly.

this is what I use along with a wax every few months and headlights don't oxidize anywhere near as quickly

u/famous47 · 3 pointsr/Volkswagen

Did you use a sealer?

u/eyeoutthere · 3 pointsr/Cartalk

In my experience, it lasts at least a year.
This sealer made it last an additional year, but it still yellowed again.
https://www.amazon.com/dp/B0051PJWQW/ref=cm_sw_em_r_mt_dp_U_.wCDDb9E95EAM

u/lolKaiser · 3 pointsr/AutoDetailing

I've personally used CarPro DLUX on black plastic trims and its fantastic!

The cars at home are basically new so I can't vouch for anything, but opti-lens is designed for headlights. That said, if you can afford the time and handiness, it would be better to just repaint a clear coat on them.

u/thehair · 3 pointsr/subaru

I used a headlight restoration kit from the auto parts store and had pretty good results. It was this one here which had a buffing and wet sanding drill attachments and polishing compound. My headlights weren't bad so i only needed the buffing pad. If you get a kit, make sure it has drill attachments and that the sanding pads are wet sanding (not dry).

u/TheSplendiferousSpy · 3 pointsr/Miata

Refinish the headlights.

I have tried a bunch of different solutions, the best one is to sand the headlights, from 800 grit > 1600 grit > 2000 grit > 3000 grit, something along those lines. Finish up with a plastic headlight polish like PlastX, then mask the surrounding paint with a cut plastic bag + tape (use painters tape around the headlights during sanding, or even better take them off to sand and paint them), and finish it up by spraying Meguairs Headlight Coat on it, wait 5 minutes, and give it a second coat. Should come out close to perfect, and will last at least a year. Using just PlastX polish will last for maybe a few weeks before fogging again. I tried mixing spar urethane with mineral spirits, 50/50 and that only lasted a few months before fogging up, it dried yellowish as well.

I used this kit for the sanding pads, you can use the powerplastic polish instead of the plastx stuff.

I would heavily recommend a cordless drill for the sanding and polishing

This is the headlight spray

u/Salamandastron · 3 pointsr/genesiscoupe

Sorry, I forgot to link you the little plastic adapters. It's like a little collar it fits into. Super cheap and that's all you need to get an H7 size LED to fit.

https://www.amazon.com/dp/B01J5SCQ1I/ref=cm_sw_r_cp_awdo_t1_dn9ADb88PX35V

u/MinnesotaTemp · 3 pointsr/Honda

Don't forget to apply UV headlight sealant after compounding her lights. I think this will offer the biggest improvement in effective visibility in terms of lighting. Then yes change the bulbs, they dim out over time as the tungsten vapors from the filament coat the inside of the headlight bulb glass. Personally I would just get some Sylnvania XtraVision bulbs instead of those 'high performance' burnouts like SilverStars and Osram NightBreakers. The way halogen bulbs work is, 10% overpowered from normal design decreases bulb life to just 1/3 life, and 10% underpowered from normal wattage will increase bulb life by 3 times.

u/Throw_Jim_ · 3 pointsr/AutoDetailing

Are you talking about this.

So do you recommend applying this after restoring headlights? If you don't apply something like this will the headlight just re-oxidize quicker?

u/machu505 · 3 pointsr/fixit

Headlight cover polishing/cleaning kit. Uses 2 progressively finer sandpapers (2000 & 3000?) to wet sand out the scratches, then a buffing compound to polish back to clear. Works great. This is what I used.

u/nj2fl · 3 pointsr/mildlyinfuriating

These two things and some tape are all you need for beautiful headlights. You go through the levels from coarse to fine sanding in alternating directions, vertical with one pad then horizontal with the next. You only need to use 4 or 5 pads, I went through the whole set the first time and found the last couple to be too fine to do much. Clear coat after they're sanded and dry and your good to go for years to come.

2 inch by 2 inch Micro Mesh Soft Touch Sanding Pads
https://www.amazon.com/dp/B000H6EC4C/ref=cm_sw_r_cp_apa_i_TuITCbWP205TA

Meguiar's G17804 Keep Clear Headlight Coating
https://www.amazon.com/dp/B01M4RVVX6/ref=cm_sw_r_cp_apa_i_6wITCbNGG9B7W

u/TheSevenFive · 3 pointsr/WRX

Same, I've had the car for three weeks and have been debating it the whole time. I read that you can reuse it, and after opening it did seem fine enough to reuse but I didn't want to risk it, resealed it with Mirimoto Retrorubber Butyl sealant

u/jwaterworth · 3 pointsr/AutoDetailing

I've used the kit a couple of times before, but this time it looks like theyve changed up the procedure. They still have the standard sandpaper that you use with the drill, but they no longer include the polish/compound or polishing pad. After using the highest grit, it gives you a coating to cover the headlight while it is still cloudy. After 2 coats the headlight looks crystal clear. The coating claims to last "4x longer!" but doesnt say how long it should actually last for.

https://smile.amazon.com/3M-39175-Heavy-Headlight-Restoration/dp/B072FQMY3Z

u/kev-lar70 · 3 pointsr/sailing

This worked well on my car - https://www.amazon.com/3M-39175-Heavy-Headlight-Restoration/dp/B072FQMY3Z

It has all the items that FlicrPaul mentioned, plus a "protective clearcoat". I'm going to try it on my compass, after I work through a bunch of other things on my ToDo list.

u/tquiring · 2 pointsr/Acura

This is the one i bought and used, took about an hour for each headlight, you will need an electric drill and a roll of painters tape.
Pro Tip: Put lots of tape around each headlight at least 3 layers thick (because you WILL hit it with the sandpaper)

https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_3?ie=UTF8&qid=1484940876&sr=8-3&keywords=3m+headlight+restoration+kit

I was skeptical before i tried doing this, but it actually worked really really well. Best of Luck.

u/xHaZxMaTx · 2 pointsr/automotivetraining

Seriously, $14 and less than an hour. Though sealing the lens in a little more expensive. I just did mine this past weekend: before and after. Sealed them with Optilens which is pretty expensive, but supposed to last the life of the car.

u/gedden8co · 2 pointsr/vintageaudio

That is also basically what I just used from 3M to restore my headlights. It was 2 sandpaper steps, a trizact pad, then polish.
This is the kit
Edit: And the headlights

u/SupaZT · 2 pointsr/LAlist

Yeah I researched this at one point but never got around to it. All I saw was Toothpaste + Baking Soda.. and sand paper.. but never a UV blocker. Prob is i'm 20 miles away haha. My car is 8 years old though and they are starting to fade.
I bookmarked these at one point but never got around to buying them

and https://www.amazon.com/dp/B004GFTC0E/_encoding=UTF8?coliid=I3L2KS0GBXFJH1&colid=1S9C9YTG1AAL9

u/gear9242 · 2 pointsr/MyLittleMotorhead

With this! The reviews are pretty darn accurate. From my experience, be very liberal when you apply the masking tape around the lights, and you might have to break out the old elbow grease for some corners.

Otherwise, shit works like a charm.

u/ucfierocharger · 2 pointsr/vinyl

I've used this on multiple tables. It works wonders, but be sure to put some masking tape over that little technics logo in the center. Plus you can shine up your headlights afterwards!

http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

u/dsteele713 · 2 pointsr/cars

Assuming you have a drill, $13 for a 3M Headlight kit. I drive a 2001 Honda and just did mine, and the difference was quite noticeable. The headlights are much brighter now since it's not being absorbed and redirected by those cloudy-ass lenses.

I'd spend $15 on an OBDII Bluetooth adapter and ~$6 on the premium version of the Torque app so you can read fault codes and real-time engine data.

We're at $34 right now. I'd buy a bottle of rain-x, some microfiber towels, and some cleaning products for my car (glass cleaner, soap, wheel cleaner, etc.), and that might come to another $30, though you could easily spend more if you don't have any cleaning supplies or decide to get all the goodies. I would then spend a few hours and go to town on your car. The few hours I spent were totally worth it when I consider how much more I enjoy driving my car now.

Finally, I'd buy a nice cabin air filter for $15 or so and replace the old one that is probably long overdue (when I replaced mine I found it had never been replaced in the car's 185k service). That will increase the quality of the air coming in quite noticeably.

We're at $79 so far. I would go on your car's forum to see if there are any cheap fixes or improvement you can make to the car. I had a problem where sometime when the car would go over bumps or take a hard turn I would hear this squeaking noise. Turns out that the front suspension bushing can rub against the bare metal surrounding them when they get old, and a few bucks worth of lithium grease will quiet them down to where you can't hear them. Simple, cheap fix that made me love the car more. See if you can find something like that for your accord.

I also think minerdeity's Aux to bluetooth adapter would be great if you have an old car that doesn't have bluetooth.

u/brimstn · 2 pointsr/MechanicAdvice

First, you’re going to need a drill with a chuck instead of a 1/4” bit holder. This is a good start:

https://www.amazon.com/dp/B001AIZ5HY/

If you don’t have a good drill, there’s this one but you’re in for some elbow grease:

https://www.amazon.com/dp/B006VB8JTQ/

u/Preact5 · 2 pointsr/Integra

Thank you! I think they look 90% as good as new!!

I used the 3m restoration kit

3M 39008 Headlight Lens... https://www.amazon.com/dp/B001AIZ5HY?ref=ppx_pop_mob_ap_share

And this Sylvania restoration and UV coating

SYLVANIA - Headlight Restoration... https://www.amazon.com/dp/B01KIVYE6G?ref=ppx_pop_mob_ap_share

u/dgtlgk · 2 pointsr/vegaslocals

I second the idea of just doing it yourself. The sylvania kit the other commenter posted will work just fine if you’re doing it by hand. If you have a powered drill then I’d recommend this 3M one instead. Worked great for me on two separate vehicles.

3M 39008 Headlight Lens Restoration System $11.04
https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_cp_apip_65SxnkKBqipTr

u/govtwtchdog · 2 pointsr/SubaruForester
u/tabatchoy · 2 pointsr/Trucks

I wouldn't do that since the toothpaste method is just a band-aid solution. I recommend a headlight restoration kit.

Shameless plug to /r/AutoDetailing

u/ICA2015 · 2 pointsr/rav4club

This is the one I got for mine: 3M 39008 Headlight Lens Restoration System https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_cp_tai_QEg7Bb85Z7MR1

u/LagCommander · 2 pointsr/cars

I use the 3m kit plus this sealant and it has personally worked out pretty well for me, but I'm a pretty amateur detailer.

I also have done a decent amount of side work with it and prefer to do the lower grits by hand and use a drill/polisher for the 2000 grit sand + polish.

Edit: I'll add it's probably not a permanent solution, but on my previous vehicle I had a lot of trouble with cheaper "headlight protectants" and it would slowly start to yellow after 4 months. Not major, but enough for a detailers' eye to notice. With the meguiars I never noticed it again.

u/Mako18 · 2 pointsr/AutoDetailing

I finally got around to fixing the cloudy lenses on my 2001 VW Passat.

http://imgur.com/a/HvVe9

I used:

  • 3M headlight restoration kit
  • 3M Green Masking Tape
  • DeWalt corded power drill
  • Microfiber cloth

    A couple notes for anyone considering doing the same:

  • Definitely use at least two layers of tape anywhere the sanding disk might make contact with the body. Keep a close eye on the tape to make sure you're not wearing through. The shape of your headlights and front-end may make it easier or harder to avoid hitting the masked areas. Remember: tape: $7/roll, fixing a spot that you sanded through on your bumper: more than $7
  • My drill had a max RPM of 2600, directions call for a max of 1600 RPM, so I was careful to avoid going "full throttle". Going too fast can cause things to get too hot when sanding, and cause more harm than good.
  • Don't be stingy with your sanding disks. You'll probably have extra, but making a couple extra passes is much better than a couple too few, because if you don't take off enough material at any stage, it will be difficult to compensate later.
u/i0nicx · 2 pointsr/RX8

I picked up a 3M kit, here's the link

u/I_Kick_Boxes · 2 pointsr/G35

Just used the 3M headlight restoration kit (with rotary/drill attachment) and also used this Meguiar's headlight coating
to seal it in a little. Been over a year and still lookin fresh!

u/ratamack · 2 pointsr/MechanicAdvice

Use the 3M headlight restoring kit or order new assemblies on ebay.

3M 39008 Headlight Lens Restoration System https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_awd_gLhXub11M1FF3

u/PancakeZ33 · 2 pointsr/350z

You could also try using the 3M Headlight Restoration Kit.

u/couchst · 2 pointsr/Portland

AFTER TRYING SEVERAL, THIS ONE: http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_2?ie=UTF8&qid=1450143916&sr=8-2&keywords=headlight+restoration WORKS REALLY GOOD BECAUSE YOU HOOK IT UP TO A DRILL. IT TAKES A WHILE BUT IT WORKS

u/showmethestudy · 2 pointsr/LifeProTips

3M Headlight Cleaner System

Works amazingly well. I love it. Really cheap too.

u/fripletister · 2 pointsr/LifeProTips

If you have a drill, get a 3M headlight restoration kit. Comes with all the sandpaper pads, compounds, etc that you need, and it's easy. $15 well spent, IMO - took me a couple of hours to do both headlights because I took my time, but they turned out like new.

u/gh0stmach1ne · 2 pointsr/civic

Sure did! I used this and then this to seal it

u/throwaway7n3xp0 · 2 pointsr/GrandCherokee

I highly recommend this 3m headlight restoration kit.

It worked great on the one WJ headlight I did. It did all I could ask for, but the pitting in places was too deep. I bought a set of new ones on ebay for $80.

The quality is not OEM, but for the money they're spectacular and you would think they're OEM looking at the face.

The only issue is regular 9006 headlights won't go into the low beam housing. You need to use 9006xs bulbs which are a straight piece instead of having the 90 degree bend for the plug.

u/SkeletorTheSpook · 2 pointsr/XTerra

If your headlights were as bad as mine, I can completely recommend the 3M headlight restoration kit.
https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_sms_apa_i_Kc1SDbG9AHEW7

It worked insanely good and made the process easy, plus it was only $11. Just follow the instructions and it'll go well, plus a lot of people recommend clear-coating. I can't really do that because the humidity pretty much stays above 80% down here, but the kit has enough material and polish that it could be used a couple more times to do maintenance.

u/mag0802 · 2 pointsr/Mustang

http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

There's a $5 rebate on it too. You need a drill to attach the pads to, some painters tape, a microfiber towel, and a spray bottle. But it worked flawlessly.

u/Daamus · 2 pointsr/infiniti

This is the exact one i bought, and it turned out really nice, as long as you take your time and do each step thoroughly you will be in good shape.

u/ForHumans · 2 pointsr/Volkswagen
u/jermvirus · 2 pointsr/BmwTech

Let me start by saying i think i over did it, but I am happy with the results



Let's start with what I purchased:

  1. Turtle Wax 50764 Drill-Based Headlight Restorer
  2. 3M 39008 Headlight Lens Restoration System
  3. Turtle Wax T-43 (2-in-1) Headlight Cleaner and Sealant - 9 oz



    Then this is the process I used:

  4. Start dry sanding with 3M #1 and then #2 Disc
  5. Wet sand with Turtle wax #1 > #2 and finally 3M #3 disc
  6. Buff with Turtle Wax compound, repeat this step until i was happy
  7. Apply clear coat from TurtleWax kit
  8. Apply sealant from TurtleWax kit



    I plan to touch up with the TurleWax sealant every 8 weeks.



u/ZZZ_123 · 2 pointsr/lepin

Also, I have this kit at home and going to try and first polish it this way, before spending any money. I'll report back about this first.

https://www.amazon.com/gp/product/B001AIZ5HY/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

u/hawkweasel · 2 pointsr/Acura

Sure thing!

Caution: I'm an idiot and got a little overzealous when I first started. Though I placed tape on the paint around the headlights, I pressed a little too hard at one point and the sandpaper went through the tape and scuffed up my paint just a little. Be gentle and careful and you'll be fine. Use multiple layers of tape too.

https://www.amazon.com/gp/product/B001AIZ5HY/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1

u/powersaucebar · 2 pointsr/Honda

The easiest way is to buy a headlight polishing kit. 3M sell one.

http://www.amazon.com/gp/aw/d/B001AIZ5HY

u/jennyrodo · 2 pointsr/Shoes

Maybe try the stuff you use on headlights? Obviously wash them really well before you put them back on your child's feet, but it's worth a shot?

u/korben1301 · 2 pointsr/4Runner

I park in a garage most of the time which helps a lot, but a couple times a year I use this stuff

It takes a bit of elbow grease but works well. Never heard of the brand but my dad randomly picked some up at Walmart one day and let me try it. Been using it ever since.

u/AwwMangoes · 2 pointsr/LifeProTips

I've used this a couple of times and it's worked wonders.

Blue Magic

u/DubstepMeGusta · 2 pointsr/Toyota

Turtle was headlight restorer. I bought it at Wal-Mart for 10 bucks, not a single bit of regret.

u/almightywhacko · 2 pointsr/pebble

Turtle Wax Headlight Restorer might work on larger scratches. I would start with the finest sanding pad and then finish off with the polish and a cloth and then do a coat of hard wax.

u/lobuzz311 · 2 pointsr/Volkswagen

This stuff works wonders, and it's less than $10.
http://www.amazon.com/Turtle-Wax-T-240KT-Headlight-Restorer/dp/B001TI5IIQ

u/MOONGOONER · 2 pointsr/vinyl

You can probably fix that cloudy dust cover by getting some headlight cleaning fluid. You can find it pretty much anywhere you buy car parts, takes like 2 minutes and looks much better

something like this

u/odd_affiliate_link · 2 pointsr/AskReddit

Same concept, better product. Be prepared to spend some time to do it right (~1 hour). However, the final effect was worth it for me.

u/pinkflowers · 2 pointsr/Cartalk

Not sure if anyone has mentioned this yet, but I very highly recommend this kit- http://www.amazon.com/gp/aw/d/B001TI5IIQ The reviews speak for themselves. My headlights were total shit and were becoming a hazard, because I could barely see at night. I picked this kit up from walmart for $9, so you should be able to find it at walmart for around the same price.

u/ihit18today · 2 pointsr/G35

SYLVANIA - Headlight Restoration... https://www.amazon.com/dp/B00429NKWK?ref=ppx_pop_mob_ap_share

I used to work in a shop and we used to have the gs guys do these.100% beginner friendly just follow the instructions.Everything is done by hand.

u/wdiesch1 · 2 pointsr/hondafit

This is the best:

Sylvania Headlight Restoration Kit

I have used it in two cars just as bad as your Fit and they both had perfectly shiny lenses for over a year.

Sylvania Headlight Restoration Kit Amazon

u/RanchCornNutsYes · 2 pointsr/Acura_RSX

I used this kit with excellent results.


  1. Wash the headlights by hand

  2. Wet send it in order from lowest grit to highest

  3. Use a polishing compound to polish out the fine scratches made by the highest grit sandpaper

  4. Use a soft buffing pad to give it a final touch

  5. Clean and apply a new layer of sealant

  6. Done


    If you're open to it, projector headlights are pretty cheap now. Mine (halo style) were $280 and came with an HID kit.

    Edit- I should mention that the quality of your result will 100% depend on how much work you put in to the wet sanding steps and how well you evenly sanded the entire surface.
u/[deleted] · 2 pointsr/Volkswagen

I used the 3M headlight restoration kit on my MKIV, but this one is better rated AND comes with a sealant to keep the results. One of the biggest issues with restoring is that sometimes they become cloudy if you don't use sealant. (http://www.amazon.com/Sylvania-38771-Headlight-Restoration-Kit/dp/B00429NKWK).

Depending on how deep the scratches are you may be able to lightly sand down down the clear coat and buff it, unless its completely through the clear coat and through the paint and/or metal. Looking at those, they look pretty deep. I would suggest using OEM paint pens, blobbing paint on the scratches, and letting them set for a week. Then you sand down with 2000 or 3000 grit sand paper, buff, and repeat until satisfied. Then apply a clear coat, lightly sand down, and buff to a shine. Letting the paint set is pretty important. You could also look into Dr. Colorship, but thats really not for scratches and more for chips on the front hood, which I'm pretty certain you have (the hood pretty much asks for it on these cars).

As far as the mirror, I'd see if any junk yards around you have a mirror on a junked car. If a different color, plasti-dip both mirrors black.

u/imnotstas · 2 pointsr/Stance

My only advice to you..

Look into this..

Beautiful car man.

u/SiffLawd · 2 pointsr/mazda

Mine were a lot worse than this and I've tried just about everything on the market. About a month ago I was at Pep Boys and found a new one from Sylvania. It is the best thing I have ever used, I really wish I would have done a before and after. Amazon link http://www.amazon.com/Sylvania-38771-Headlight-Restoration-Kit/dp/B00429NKWK

u/3rdtimes · 2 pointsr/mazda

I'm not sure what he used, but I have a 07 Mazda 6 and I used this headlight restoring kit from Sylvania, and it did an amazing job! It has a lifetime warranty and it has lasted over a year so far. It took about an hour to do both headlights and I got mine at an Advance Auto store if that helps.

u/BallsDeepInJesus · 2 pointsr/projectcar
u/dr2fish · 2 pointsr/GrandCherokee

Cool! It looks great. I picked mine up last year for a little over a grand and have been working on bringing it up to mechanical speed - mostly deferred maintenance stuff - but now I kind of love it and want to start upgrading.

For the headlights, I've had great luck with the 3M kit on amazon. There are a couple variants, all the same basic thing - sand down the worn plastic, put on a protective coating, looks good as new. Don't bother with stuff like PlastX unless you feel like reapplying every few weeks.

u/Iheartbaconz · 2 pointsr/Honda

Jesus, you went balls out. I was just going to use something like this: https://www.amazon.com/Blue-Magic-730-6-Headlight-Sealer/dp/B0051PJWQW

At this point i fucked up one of my headlights and like melted it sanding it with a disc that came in a restore kit. I donno wtf happened, but there are like burn marks in the drivers side. So it needs replaced anyways.

u/tagrav · 2 pointsr/S2000

You need to protect it somehow.

original headlights will typically have a protective layer above that you have sanded off now.

I like what the other guy said about clear 3M vinyl

my headlights I restored 2 years ago and they are fading already without any protectant other than 3x yearly application of collonite 845.


there's also a product by opti called opti lense that you apply a clear coat over top. https://www.amazon.com/OPT-OPT-OLC10-Opti-Lens-Permanent-Headlight/dp/B00GULJCUM

u/freaksavior · 2 pointsr/AutoDetailing

I've heard really good things with Opti-Lens

u/engwish · 2 pointsr/AutoDetailing

Are you sure you used the kit correctly? I restored my beater's headlights with Megiuar's G3000 kit and the turnout was pretty good. The thing is, the entire process took me about 30 minutes of sanding per headlight (I was a bit timid with it at first).

Additionally, headlights need to have UV protection on them or the hazing will come back. The gel stuff that comes with the kit will only last about 1 month before you need to re-apply it. Your best bet is to apply a longer lasting product like Opti-Lens to ensure permanant protection.

u/JacobeyWitness · 2 pointsr/370z

I used Mothers NuLens to restore and remove oxidation and then finished with Meguiars Headlight Coating to prevent more oxidation. Only time will tell how well the coating worked but the headlight restore process was no big deal if I have to do it again in a year or so.

u/Cowsmoke · 2 pointsr/genesiscoupe

Awesome glad I could help! You’ll have to get creative with how you install them since they have they’re own driver box kinda like HID’s (unlike the aux beam where it’s built into the light) So you’ll have to mess with it for a little until you can make it fit, and You’ll need these adapters but you probably already have them if you have the auxbeams. And if you’re looking for fog’s these are what I have and I have no complaints with them, they’re pretty bright and match the same kelvin value as the headlight LED’s

u/Migitoncrack · 2 pointsr/MitsubishiOutlander

I used the following adapter:

GZXY H7 LED Headlight Car Bulb Adapter Holder Socket for KIA K3 K4 K5 Sorento SportageR Coupe Grand Santa Fe Hyundai Sonata9 Coupe Veloster 2pcs https://www.amazon.com/dp/B01J5SCQ1I/ref=cm_sw_r_cp_api_i_vho1Db8BM1VAZ

And for the LED Lights you can use any any H7 bulbs I believe. I used a company called AuxBeam.

u/wrexecute · 2 pointsr/genesiscoupe

I got these for the ambers. Still kickin since 2017. Can't say the same for the tag light or interiors tho.. Avoid big packs of cheap LEDs, they're just waiting to flicker.

Low Beam I'm quite happy with these although they don't really fit inside. You'll need something like this and optionally a pair of these to seal it up, but a lot of ppl don't.

u/rjohns1 · 2 pointsr/Cartalk

Those kits will work long term, but you have to treat them for UV. Use this after you polish them: https://www.amazon.com/Sylvania-Headlight-Restoration-Block-Clear/dp/B01KIVYE6G

u/PapiSmear · 2 pointsr/AutoDetailing

I read good reviews on forums about this one, so I bought that for $10. LINK

u/Entrical · 2 pointsr/Toyota

That won't be a covered repair. I would get this

u/bro_some · 2 pointsr/Acura_RSX

Try the Meguiar's heavy duty headlight kit Worked really well for me on my CRV's really faded lights.

Started with 600 grit, then followed the directions on the box, just changing sanding directions (up/down vs left/right) after every step in grit. Go slow, and use a lot of water, takes about 30-40 minutes per light to get it lookin right but its worth it. Before and After results with said kit.

u/isittooearlyforbeer · 2 pointsr/BMW

Yes it does. Four steps total; 1000 grit sanding, 3000 grit sanding, plastic cleaner w/ drill operated buffing wheel, then sealer.

edit: Amazon link to the product I used https://www.amazon.com/Meguiars-G2980-Heavy-Headlight-Restoration/dp/B01M2D763D/ref=pd_lpo_vtph_263_tr_t_2?_encoding=UTF8&psc=1&refRID=JWS85HZN5XR0X4HH5BNY

u/tubetraveller · 2 pointsr/genesiscoupe

I've never used it, but Meguiars makes a headlight coating that is supposed to provide UV protection.

https://www.amazon.com/Meguiars-G17804-Clear-Headlight-Coating/dp/B01M4RVVX6

I've been looking at getting those same headlights.

u/LarsAlereon · 2 pointsr/NoStupidQuestions

You can fix this long-term (but not completely permanently) with two steps: First, thoroughly clean the headlights using Meguiar's PlastX, which will restore them to brand new shine. Next, apply a layer of Meguiar's Keep Clear Coating, which will keep the headlights from fogging again for up to one year. You can probably use a different brand of coating, but I haven't found anything else that works as well as PlastX.

u/beengel · 2 pointsr/RangeRover

I recommend applying this product after the polish. I have done two sets, the first one I left bare and it yellowed in just a year. The second time i used something like thisand it has been 18 months and looks great still

u/BrotherAliMazda · 2 pointsr/mazda3

My headlights were MUCH worse (long story). I used this (since its out of stock just get a similar kit on amazon):

https://www.lowes.com/pd/Gator-3-1-in-Headlight-Restoration-Kit/4747427

and this (plan to reapply this every year or so, heard about it on scotty kilmer youtube channel):

https://www.amazon.com/Meguiars-G17804-Clear-Headlight-Coating/dp/B01M4RVVX6

It was really easy and worked amazingly. IMO dont even waste your time or money buying sandpaper and doing it by hand, this is basically the same cost or so and much easier

EDIT: This on amazon should work well

https://www.amazon.com/Headlights-Taillights-Restoration-High-Precision-Waterproof/dp/B07KP8J7Q2/ref=sr_1_9?keywords=headlight+sandpaper&qid=1573631053&sr=8-9

https://www.youtube.com/watch?v=r_k4NtNLAwY

u/biking4jesus · 2 pointsr/4Runner

Meguiar's G2970 Two Step Headlight Restore 2Step, 4. Fluid_Ounces https://www.amazon.com/dp/B01M75GUJB/ref=cm_sw_r_cp_apa_i_jf0nDbZ1D9DHV

has worked well on several cars in Arizona for me

u/mellowpanda1 · 2 pointsr/MINI

If you have access to a polisher, avarax's method would provide good and longest lasting results. The PPF is not that hard to put on.

​

If you have a power drill, here is a headlight restoration kit that I used and lasts for a while.

https://www.amazon.com/Meguiars-Two-Step-Headlight-Restoration/dp/B01M75GUJB

u/Tical79 · 2 pointsr/AutoDetailing

It's fine. The tool is especially handy. However, if they are grimey or just lightly oxidized, you can use this kit.

https://www.amazon.com/Meguiars-Two-Step-Headlight-Restoration/dp/B01M75GUJB/ref=mp_s_a_1_8?keywords=headlight+restoration+kit&qid=1570269734&sr=8-8

It has the clear coat that will prevent it from recurring for a year.

If they are bad, stick with the kit you suggested, and buy that spray separate fir $8

u/zar_lord · 2 pointsr/Camry

It just rained XD. And nope, factory headlamps, I cleared them a bit with Meguiar's Headlamp Restoration thingy

u/HanoverWilliam · 2 pointsr/4Runner

> What HID kit is that, and how easy/hard was the install?

It was a morimoto kit. Square D2.S model


It wasn't difficult. Just laborious.


Steps I took:

  • Sourced some glass headlamps on amazon of all places.
  • Here
  • & Here
  • Disassembled them
  • Heated them up like instructed here.
  • Scuffed, sanded, and painted the reflector interior. 10 coats of matte black spray paint.
  • Purchased Square D2S projectors (square probably discontinued) and harness from SparkSmith.
  • Reapplied the goop adhesive for the glass on the edges with this stuff.
  • Reassembled glass back on. Applied pressure with some clamps. Reheated in oven.
  • Reassembled.
  • Called SparkSmith and they recommended I purchase 5500k HIDs and paired harness. (Great guys btw)
  • Installed.

    This took me 3 months to get done, mistakes inclusive. Because I live a VERY busy lifestyle. You could do it with my advice in two weeks and one dedicated day, shipping time included.
u/silentb00m · 2 pointsr/saab

With something like this:
3M 39175 Heavy Duty Headlight Restoration Kit
https://www.amazon.com/dp/B072FQMY3Z/ref=cm_sw_r_cp_api_i_LD4SCbDFZWYRC

u/longlivelongboards · 2 pointsr/4Runner_1stGen

I meant to reply to this.

wiring harness

A friend gifted me the lamps but you can probably find them on amazon.

It was an easy install and the lights are awesome

u/reverbro · 1 pointr/DIY

You need a plastic polishing solution, either a DIY like toothpaste and finer polishing pastes, or an off the shelf deal like a headlight restoration kit

u/ThoR294 · 1 pointr/pics

They also sell kits for headlight restoration. 3M one is amazing. I've done about 3 so far and they are flawless. This one requires a cordless drill, and it makes it super super easy and less stress on your arm lol.

Also, for your rust spot, it's not coming through the back right? I know subaru's they like to rot behind, so maybe get behind there with some undercoating spray to make sure it doesn't come back!

u/MyDogIsJack · 1 pointr/subaru

Basically the 3M kit which works amazingly well.

u/Diaggen · 1 pointr/Eugene

Try the toothpaste method mentioned in this article (Method 3 at the bottom). If that doesn't work well enough, 3M makes products like this one on Amazon that work.

I've personally used both methods, I always try toothpaste first as it is always the cheapest.

u/Bananaz · 1 pointr/S2000

If you have a cordless drill purchase the 3M lens cleaner: http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_2?ie=UTF8&qid=1396048236&sr=8-2&keywords=3m+lens+cleaner

There are more than enough pads in there for 2 headlights. Take off your front bumper and put up your hood, this will make the task so much easier. Triple painters tape the paint around top and sides. Get a squirt bottle from Autozone, Homedepot, etc and fill it with water. Take your time, it should take around 45 minutes to do both.

Also do them at the same time, each step. Don't complete one and move to the other.

Afterwords protect and clean with: http://www.amazon.com/Meguiars-PlastX-Plastic-Cleaner-Polish/dp/B0000AY3SR/ref=sr_1_5?ie=UTF8&qid=1396048450&sr=8-5&keywords=3m+lens+cleaner

u/achenx75 · 1 pointr/AutoDetailing

Like VibeRaider said, use this.

https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY/ref=sr_1_4?s=automotive&ie=UTF8&qid=1511332433&sr=1-4&keywords=headlight+restoration+kit

It works great and remember to use a sealant after you're done or your hard work will be thrown away.

u/jvb93 · 1 pointr/BMW
u/TheOtherMagician · 1 pointr/AutoDetailing

This is the product I used I followed their instructions exactly. There were 3 different sanding pads that came with the kit:

First I used the 500 grit dry and lightly went over the entire light.

I wiped away excess dust and switched to the 800 grit dry and went over the entire light.

I wiped away that dust and then wet the light and 3000 grit pad.
I went over the entire light 4 times with the wet 3000 grit.

Afterwards I used the 3M polishing compound and the foam head to polish the light.

I used the wax that came in the kit to finish up.

Here is a pdf of the instructions that came with my kit

u/unknownsoldierx · 1 pointr/DIY

There's two 3M kits. The $14 3M Headlight Lens Restoration System and the $16 3M Lens Renewal Kit. Looks like the more expensive kit is a 4-step process rather than 3-step and you get maybe some different pads and some masking tape.

u/IzttzI · 1 pointr/MINI

http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

Is the kit I used and it works perfectly well and actually had enough to do my other car too.

u/thataryanitalianguy · 1 pointr/AutoDetailing

Was this kit the kind that attaches to a drill? I've used the 3m kit and the results look straight outta the factory.

u/Balki_Bartokumos · 1 pointr/Cartalk

Try this: https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_other_apa_i_3FSCDb7XBRWXF

I've used it before, and it worked pretty well. However, make sure to tape around the borders of the headlights

u/zimraph · 1 pointr/GolfGTI

What did you use? 3M 39008 ?

u/TrekkingForward · 1 pointr/Wellthatsucks

For the headlights, use a restoration kit. Looks like they could use a shining anyways.

Best one I’ve used

u/mckulty · 1 pointr/Birmingham

The last kit we bought worked pretty much like we do surfacing lenses for eyeglasses.. coarse grit, fine grit, polish. Pretty sure it's the same high-impact polycarbonate.

Just saying, if you follow the instructions and apply proper elbow grease, the 3M kit worked great for us. I recommend a kit you use with your cordless drill.

u/BalrogAndRoll · 1 pointr/BMW

This one is very highly recommended.

Check out /r/AutoDetailing

u/k_ba · 1 pointr/AutoDetailing

3m kit - 14 bucks on amazon. It has a final rubbing compound after the sanding. Then seal it once again, and you are good.

I took some terrible forester headlights to perfectly clear and beautiful with it. AND it allows you to use your drill to polish. Which makes it WAY better.

u/iamsaver · 1 pointr/prius

I've done the same using the 3m kit, which includes a drill attachment. Super easy and effective. Hardest part was masking the painted areas first. Most people recommend putting some sort of wax, so I picked a wipe on product too.

Headlight restoration kit
https://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY?th=1&psc=1

Clear coat
https://www.amazon.com/gp/aw/d/B079QL8BYK?psc=1&ref=ppx_pop_mob_b_asin_title

u/FlyingButtresses · 1 pointr/BMW

My dad had this for awhile and I decided to use it. But if I had the choice I definitely would have gone with this only because it's much easier. If you do end up going with the 3M one make sure you have some type of UV Protectant or sealant to coat the lights with afterwards so they don't get foggy again too quickly. The one I had included the sealant and the instructions were pretty straightfoward on the box.

u/patbak13 · 1 pointr/BMWE36

I used this 3M Headlight restoration kit! It worked very well. After this picture was taken, I waxed the lights with plastic compounds.

u/SplitMyPants · 1 pointr/subaru

It doesn't make you sound dumb, I'd rather see something unique and cool instead of the same mods that are done over and over again.

If you're looking into RallyX have you thought about swapping over to Forester suspension to raise it up a bit?

I'd go the Cobb AccessPort route instead of tactrix because of the simplicity and now that the V3 has come out, the V2 is around $100 cheaper I think. But if you're comfortable doing it that way do it.

I'm not sure if it's just the picture but the headlights look a bit foggy. I used this on my first car a few years ago and it worked great. Most of the other headlight restoration kits are bullshit. You could also bake them open and paint the plastic pieces black to spice things up.

If yellow foglights are your thing I used this on my Subaru and I love it. Just takes around 5 light coats on the outside of the fog lights and you're good to go. Much better than any of the tint overlays or light bulbs.

Here's some information on it. Daniel Stern is pretty well known as the lighting expert.

Another thing you could consider if you want to mix things up is plastidipping your car. DipYourCar has some wild colors, Sunset Orange and Tiffany Blue are my personal favorites. I'd stay away from the normal black though, it normally makes cars look pretty trashy.

Hopefully it doesn't sound like I'm telling you what to do with the car, just giving suggestions. Good luck!


u/cheapngood · 1 pointr/scooters

You can buy headlight polishing kits at any auto parts store. It's a long process, sanding with finer and finer sandpaper and a drill. http://www.amazon.com/3M-39008-Headlight-Restoration-System/dp/B001AIZ5HY

Much easier to just order a new visor. Most helmet brands sell them. You can also buy visors with anti-fog coatings.

u/AKADriver · 1 pointr/funny

It works only on lights which are so worn that the hard coating over the polycarbonate hasn't just gotten hazy, it's worn off. Also it doesn't work on glass headlights. At any rate it's the wrong product.

At any auto parts store they sell a little bottle of plastic polish for this purpose. Sometimes it comes as a kit with a foam polisher ball that you put in an electric drill and a can of clearcoat to protect the new polished surface. Doing it by hand with toothpaste just to save ten bucks is tiring and stupid.

u/Rlight · 1 pointr/Cartalk

I was reading the reviews on that, and it looked really good. Was this the one you were thinking of?

u/Linuxxx · 1 pointr/LifeProTips

My headlights were much more hazy than that, so I spent a few bucks on this. Worked like a champ!

u/g0ldendomer · 1 pointr/Lubbock

Have you just tried the toothpaste/compounds?

You need to actually sand them down progressively with something like this. Then hit it with a polishing compound, and then a UV protective coating.

u/Logan_Weapon_X · 1 pointr/Camry

It looks like you need to get a headlight sanding/buffing kit. I had the same issue on my 2002 Camry and while the low beams are still not good they improved a lot. It took me about 2 hours to do this with an electric drill. I would say this should be significantly cheaper than buying new lights.

3M 39008 Headlight Lens Restoration System https://www.amazon.com/dp/B001AIZ5HY/ref=cm_sw_r_cp_api_NFxwybNFP7FMZ

u/PeabodyJFranklin · 1 pointr/Justrolledintotheshop

Used this kit on my last car, took the lights from a yellow haze you couldn't see through, to a clear lens on one size, and slightly distorted but clear on the other (let it get too hot while sanding). I'd resisted using it, but afterwards felt it was well worth the purchase.

u/fishpuddle · 1 pointr/howto

The best method I've found is the 3M Headlight Lens Restoration System. It's easy and the results I achieved with it amazed me. I was able to do both headlights on my 17 year old cherokee in about 30 minutes or so and I only had to use one sanding disc of each grit for the entire thing. I even had plenty of polishing compound left. Just be sure to follow the instructions closely.

u/ryguy44 · 1 pointr/AutoDetailing
u/ItsSoFluffyyy · 1 pointr/AutoDetailing
u/keytarin · 1 pointr/cars

I can also really recommend the kit /u/schwartzd used. The kit includes sandpaper pads and a foam buffer that you can attach to a power drill. It was a long and kinda tedious process but the more time and care you take the better it will appear. Results also hold up spectacularly as well- previously I had used a Turtle Wax brand hand polishing kit that while did clear up the lens, the hazing was back in as little as three months. I used the 3M kit on my lenses last June and today they are still as clear as the day I bought them.

I've seen the kits go for around ~$30 at auto stores but you can get them much cheaper off Amazon.

u/PoetryfortheHunt · 1 pointr/Acura

This 3M kit is positively reviewed overall. You just need a power drill to use the attachment. If you are doing it with the headlights still in car, make sure you use painters tape to cover any painted surfaces around the edges of the headlights to avoid accidental damage during the sanding process.

u/TiePilot · 1 pointr/DIY
u/probablyhrenrai · 1 pointr/cars

Also clear head lights; the difference between clear and foggy lenses is amazing.

Cloudy vs clear and yellowed vs clear for reference; the sides with clear lenses look a few years newer.

u/brokendown · 1 pointr/subaru

I'm not sure exactly what grit it was, but I had gotten a little Turtle Wax kit to restore my headlights that game with 4 different levels of sandpaper, polish and a finishing wax. I ended up having to do it twice since the first time I didn't do enough sanding, but it took my very fogged up lights and cleared them up. During the process it'll look worse before it gets better, but it was the sanding that really did the trick.

The kit I used

u/N0_ThisIsPATRICK · 1 pointr/Volkswagen

I've never bought a set of wheels for a car. I've only had to replace one rim in a set when my sister drove the family minivan into a curb and broke a chunk out of one of the alloy wheels.
I still have the OEM Alloys on my Passat. If you are looking for a set of OEM Alloys you could check eBay, Craigslist, or a local junkyard and you may be able to get a decent set of used wheels without setting you back too much money. If you'd rather go aftermarket, I don't really know the best places to shop for rims but I'm sure many other people on this sub can help with that.

As far as the headlights go, i have used the Turtle Wax Headlight Restoration Kit and it works pretty decently. Just a little elbow grease and about an hour of your time and your headlights will look much much better.
You can also choose to just replace the headlight. A quick google search should give you plenty of options whether you want to keep the OEM look or go for something a little different.

Hope this helps!

u/cascalonginess · 1 pointr/prius

After trying to find it on the Home Depot site I realized it wasn’t 3M, it was the Turtle Wax kit. The four little pads looked pretty hokey, and they’re not the kind you can use with a drill, have to do it by hand, but it really didn’t take much to get through all four steps before applying the last two wipes.

That said, watch the video for the McGuire’s protectant someone linked further down in the comments, sounds like a more sustainable approach.

Turtle Wax T-240KT Headlight Lens Restorer Kit https://www.amazon.com/dp/B001TI5IIQ/ref=cm_sw_r_cp_api_i_aBt7CbFAKVKPT

u/Akhalyndra · 1 pointr/LifeProTips

Turtle Wax Restoration

Worked great on my car, and I had enough left over to have two other people use it with the same results. Just be sure to read the directions carefully, and do it in the shade on a day that's not so hot.

Edit: Also, don't rub it into or let it sit on the paint.

u/KuKuMacadoo · 1 pointr/S2000

Same issue but I have a 2001. I replaced mine with these and they look fantastic, the difference is insane.

https://www.amazon.com/gp/product/B004AX6NLS/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1

Also, while you're at it, I'd recommend you polish your headlamp cover up if it looked anything like mine. Had phenomenal results with this kit.

https://www.amazon.com/Turtle-Wax-T-240KT-Headlight-Restorer/dp/B001TI5IIQ/ref=sr_1_2?ie=UTF8&qid=1480912079&sr=8-2&keywords=headlight+polish

u/When_Doves_Cry · 1 pointr/AutoDetailing

Nah, this was the one where you get little square pads that you have to use by hand. This is why I'm thinking it might be a matter of agitation rather than what chemicals I am or am not using.

u/aking14 · 1 pointr/Honda

It has sandpaper and polish and sealant and stuff in it. Link

u/AlecW81 · 1 pointr/AutoDetailing

re: Headlights - Just get a kit that includes the varying grades of sandpaper, polish, and sealant.

https://www.amazon.com/SYLVANIA-Headlight-Restoration-Headlights-Protection/dp/B00429NKWK/ref=sr_1_4?keywords=Sylvania+Headlight+Restoration+Kit&qid=1564499880&s=gateway&sr=8-4

https://www.amazon.com/3M-39084-Headlight-Restoration-Kit/dp/B006VB8JTQ/ref=sr_1_8?keywords=3M+Headlight+Lens+Restoration+System+29008&qid=1564499884&s=gateway&sr=8-8

​

Soap: DO NOT USE DISH SOAP! Ever! It doesn't strip wax, but it does leave behind a film. If you want to be cheap, just get Megs Gold Class.

​

There's no reason to rinse after claying. Use either a detailing spray or a mix of Megs Gold Class shampoo and water, and dry after you finish a section.

​

There's also no reason to rinse after polishing. Just do an IPA wipe.

u/BatsAndButtercups · 1 pointr/S2000

If you're going to do DIY, I highly recommend Sylvania's restoration kit. I have used it on my daily and some of my family's vehicles as well. A headlight restoration kit is a huge waste of work if it doesn't include a clear coat! Here's the Amazon link to the product: https://www.amazon.com/dp/B00429NKWK/ref=cm_sw_r_cp_apa_i_2W6uCb4YN50C1?th=1&psc=1

u/Super_Satchel · 1 pointr/gamecollecting

Headlight polish might work for this. Something similar to this.

It's only a guess, but I would imagine the damage is similar in nature and this is a product specifically designed to correct it.

u/Crimson-Pig · 1 pointr/crv

It's almost always better to go with OEM replacement headlight units if you can. This will ensure the best fitment as well as ensure that the unit meets safety standards. This however, is expensive and takes a little bit of time. It's an easier route to restore your headlight unit if it has not been damaged other than weathering and oxidization on the surface.

I've used Sylvania's cleaning kit to great effect on my friend's 2007 CR-V. This was 3-4 years ago and the last time I saw him a few months back, the headlights have barely started to show any signs of aging.

https://www.amazon.com/gp/product/B00429NKWK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

u/JakeFortune · 1 pointr/ToyotaTacoma

I recently used this kit: https://www.amazon.com/gp/product/B00429NKWK/

Worked great, and most importantly, it includes a bottle of the new UV protectant to put on the headlights after polishing. They look brand new now.

u/RobAtSGH · 1 pointr/Volkswagen

Yes, the Wipe New kits are useless. They're essentially a Magic Eraser and some wax.

I would recommend the 3M restoration kit. It's a two-stage wet-sanding kit with disks and a pad that fits onto a standard drill motor. Comes with protectant polish and masking tape. Definitely more effective than the Rustoleum garbage.

u/hborkowski · 1 pointr/Miata

Its this kit here. http://www.amazon.com/3M-39045-Headlight-Renewal-Protectant/dp/B004GFTC0E/ref=sr_1_1?s=automotive&ie=UTF8&qid=1458948517&sr=1-1&keywords=3M+39045 Oreillys was getting rid of it and had a sale. I got it for $6, versus their price of $32. It works great!

u/SirMontego · 1 pointr/LifeProTips

I don't think the instructions say when to reapply. The amazon comments seem to say once a month or once every eight weeks. I've gone almost a year without reapplying, but I parked in a covered garage at home and work, so that limits my car's UV exposure.

https://www.amazon.com/Blue-Magic-730-6-Headlight-Sealer/dp/B0051PJWQW/ref=sr_1_1?ie=UTF8&qid=1485542376&sr=8-1&keywords=blue+magic+headlight+sealer

u/monstahtron · 1 pointr/Honda

I'll apply wax, let it dry, buff out by hand then a quick pass with this stuff.


https://www.amazon.com/Blue-Magic-730-6-Headlight-Sealer/dp/B0051PJWQW

Every now and then or whenever I feel like the shine has dulled down a bit I'll go over the bare headlight with some Plastx before applying the wax and sealant and I'm good as new again.

u/ragtopdude · 1 pointr/AutoDetailing

I've been using Blue Magic as a sealant with some success after polishing headlights.

u/xveganxcowboyx · 1 pointr/Cartalk
u/MagneticGray · 1 pointr/AutoDetailing

I use this stuff. Found it on Amazon looking for something to use after I buffed the headlights on my Mom's older Oldsmobile. They were 20 years old at the time and completely hazed over but they came out looking brand new. It worked so well that I use it on every vehicle I detail now.

A little goes a long way and it's important to make sure it's not going to rain for awhile because it can take 3-4 days to fully cure but if you do it right then it will last 6-8 months. I put it on Mom's headlights in the spring and winter and they still look new nearly 3 years after I started using the Blue Magic on them. I'm still on the same bottle too. Just an all around great product.

u/QueenAlpaca · 1 pointr/subaru

Used this to give my Bob some TLC. There was only really minor yellowing, but I'm shocked what a difference it makes. Now he looks a little more hip.

u/sonnage · 1 pointr/subaru

When what dried? Did you seal it? If you used a sealer before you buffed and polished the lens that's what could have caused this. What you need to do is restart. Sand the sealer off, and then take it easy with the sanding. And by sanding

I mean wet-sanding. I hope you weren't just using sandpaper and no lubricant lol.
Wet-sand it back down till it's smooth and hazy. Then take some rubbing compound and then buff the hell out of it till it's clear. I went crazy with mine and buffed them for a couple hours each, but i go overboard on everything. After it looks clear, wipe off the excess and let it dry. Then spray your sealant on it. Like spray paint if you get too close it'll drip, too far it won't cover fully.

I actually wet-sand mine with the 3M restoration kit: https://www.amazon.com/3M-39084-Headlight-Restoration-Kit/dp/B006VB8JTQ/ref=sr_1_4?ie=UTF8&qid=1493511799&sr=8-4&keywords=3m+headlight+restoration+kit

And for a sealer i used: https://www.amazon.com/Presta-137306-Headlight-Sealant/dp/B0082LFOFA/ref=sr_1_1?ie=UTF8&qid=1493512126&sr=8-1&keywords=renulite.

Expensive sealer I know. But I did research on it and a lot of shops use it. They actually give 3 year 30k mile warranties with it when they would redo headlights for people. So it's a good product. I used it on mine about 4 years ago and it's just starting to come off.

Hope this helps!

u/Waas507 · 1 pointr/subaru

Good tires. I like the General Altimax RT43. Regular oil changes. Regular tire rotations. Fresh fluids all around. The simple easy shit we all should be doing really.

You could also hit up your local walmart/auto parts store and buy the 3M headlight resto kit. Will get the haze off the lights and leave them shiny new for a bit. Helps a ton when there is no haze on the lenses.

https://www.amazon.com/3M-39084-Headlight-Restoration-Kit/dp/B006VB8JTQ/ref=sr_1_1?ie=UTF8&qid=1504839693&sr=8-1-spons&keywords=3m+headlight+restoration+kit&psc=1

u/rawr_imfierce · 1 pointr/AutoDetailing

So was I. This is the one i bought , but they make several kits and even the in-page description is for a different one. 39084 doesn’t include the drill attachment or a sealer. I guess since the others do I’ll definitely need something?

u/bmcclure937 · 1 pointr/AutoDetailing

Also, the 3M Headlight Restore kit is ~$13 with a $2.00 coupon and $5.00 rebate = ~$6.00

http://www.amazon.com/gp/product/B006VB8JTQ/ref=vp_c_A3VLRNJSASW98Y

u/BKFootLettuce_15 · 1 pointr/XTerra

I personally use NuLens Restoration Kit. However, it requires a drill to use.

Link: Mothers 07251 NuLens Headlight Renewal Kit https://www.amazon.com/dp/B00GZLMEPM/ref=cm_sw_r_cp_apa_i_ZsnlDbZK9TT5F

I bought this at my local O'Reilly's, however the price on the link is currently cheaper than when I bought it in store

u/chazzeromus · 1 pointr/350z

This is what I used. This stuff exceeded my expectations 110%

u/NotSuitableForWoona · 1 pointr/Multicopter

I've had some luck cleaning up CA fog with headlight restoration kits. I used this one on some acrylic and it worked quite well. It works by "melting" the top layer of the acrylic, so it may not be ideal for a thin lens.

u/bytchtytz · 1 pointr/genesiscoupe
u/ULTRAViOLET_PiRATE · 1 pointr/genesiscoupe

I have a BK2 and replaced the low beams and marker lights with LEDs and the turn signals with switchback LEDs.

I used these H7 bulbs for the lows: Cougar Motor H7 LED Headlight Bulbs, CREE All-in-One Conversion Kit - 7,200Lm 6000K Cool White https://www.amazon.com/dp/B07HKFSRX2/ref=cm_sw_r_cp_apa_i_4jqXCbAJ2CT5Y

And these adapters: GZXY H7 LED Headlight Car Bulb Adapter Holder Socket for KIA K3 K4 K5 Sorento SportageR Coupe Grand Santa Fe Hyundai Sonata9 Coupe Veloster 2pcs https://www.amazon.com/dp/B01J5SCQ1I/ref=cm_sw_r_cp_apa_i_WlqXCbTQ5G0NQ

These for the side markers: SiriusLED Extremely Bright 3030 Chipset LED Bulbs for Car Interior Dome Map Door Courtesy License Plate Lights Compact Wedge T10 168 194 2825 Xenon White Pack of 10 https://www.amazon.com/dp/B0186P1MUW/ref=cm_sw_r_cp_apa_i_PmqXCbB8G4STA

And these switchbacks: https://www.diodedynamics.com/switchback-turn-signal-leds-for-2013-2016-hyundai-genesis-coupe-pair.html



I ended up glueing the adapters onto the existing adapter already on the LED with Loctite. The hardest part was stuffing the low beam pig tail into the housing. It takes a bit k, but it is doable. I uses a 1 1/4" spade bit to drill a hole in each low beam cap for the LED fans to vent. A holesaw bit may work better. Everything else was plug and play. I still need to swap out the turn signal flasher to fix the switchback's hyperblink. I wasn't able to do the high beams because there wasn't enough space to tuck the LED pigtail in there. Any ideas for that?

Anyways it is super bright! Way brighter than the Sylvania zXe halogens I was using before. Fog lights are next then tails.

u/Madblood · 1 pointr/Chevy

I use the Meguiar's Headlight Restoration Kit It does need to be redone about every 6 months or so, but it only takes 15-20 minutes to pop out the headlight assemblies, do the restoration, and reinstall them.
BTW, is that a 2004? Looks a lot like my front end, except I have a bug deflector.

u/YaFeelZ · 1 pointr/370z

You can buy a 20$ kit from any car part store usually has different levels of sand paper grit and a polish and takes around an hour and your headlight will look like brand new once done.. just did mine. I used this onehttps://www.amazon.com/Meguiars-G2980-Heavy-Headlight-Restoration/dp/B01M2D763D/ref=mp_s_a_1_4?ie=UTF8&qid=1537212493&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=meguiars+headlight+restoration+kit&dpPl=1&dpID=51bAUJSl45L&ref=plSrch

u/AsianInvasion00 · 1 pointr/Honda

Meguiar's G2980 Heavy Duty Headlight Restoration Kit https://www.amazon.com/dp/B01M2D763D/ref=cm_sw_r_cp_api_i_eHCPDbJDP4CE4

u/mB_Roundhouse · 1 pointr/Cartalk

To build on my post: I've used this restoration kit with really good results. Your headlights may need some extra elbow grease to get rid of that outer crusty layer. But I noticed that my headlights were yellowing again within a few months, so I bought a pre-cut Lamin-X film kit. It is kind of expensive (roughly 50 bucks) but it was cut to my car's headlights exactly and sealed everything up perfectly.

In your quest to paint the car, I recommend checking out this build thread I read a while back. A guy on a forum I use completely repainted his car in John Deere yellow for pretty cheap and he documented the entire process with pictures. One of the most helpful things I have read when it comes to DIY automotive painting.

u/NE-Phil · 1 pointr/prius
u/I_Love_McRibs · 1 pointr/Acura

I also recommend the 3M kit. It took about 90 minutes of work for both headlights, but they turned out great. I sprayed a Meguiar's Headlight Coating after I was done. I restored it only 3 weeks ago, so I don't know how long the coating holds up. They UV coating spray was only $9, so I gave it a shot.

u/aarora610 · 1 pointr/infiniti

Yep they say the sealer is good for a year.

Meguiar's G2970 Two Step Headlight Restore 2Step, 4. Fluid_Ounces https://www.amazon.com/dp/B01M75GUJB/ref=cm_sw_r_cp_api_i_p0kwDb8NPH4Z0

u/alecwatersmusic · 1 pointr/infiniti

Yep! Use this. Highest recommended adhesive I could find when searching for what to use and I have it at the ready for when I re-seal my own.

u/DracoAzuleAA · 1 pointr/Saturn_Cars

You may actually be able to find some pre-built projector housings for yours. I looked and looked and looked, and the only pre-built projector housings I could find for the Vue were for year models 07 and up. Mine's an 03.

So I had to build mine. And the parts I used were pretty cheap so you might save money just building your own anyways.

Here's the parts I used

Nilight 2.5" Mini HID Bixenon Projector Lens

2x 23inch Dual Color White-Amber Switchback Headlight LED Tube Strip Light DRL Daytime Running Light & Turn Signal Lamp For Audi-Style Headlight

RetroRubber OEM Grade Butyl Headlight Sealant, Black

Everbrightt 1-Pair White 70MM 60SMD COB LED Headlight Angel Eyes Bulb Halo Ring Lamp Light With Housing

2pcs 12V HID Xenon AC Car Ballast 55W HID Xenon Bulbs Lamp For Auto Headlights For H1/3/4/7/8/9/10/11 9005 9006

HID-Warehouse HID Xenon Replacement Bulbs - H1 8000K - Medium Blue (1 Pair)

The paint I used was just a can of Rustoleum semi gloss black I got at Walmart for a few bucks.

I also purchased a separate set of headlights to do all this with, as this was my first time. I wanted to be able to take as much time as I needed with it. I can also easily switch back to stock at any time for whatever reason. I would suggest you do the same, if you're planning on building them.

To get them apart, I preheated our kitchen oven to 220 degrees. I lined an old baking pan with a wet towel and set the headlight on it, then put it in the oven for 10 minutes. This will soften the sealant enough so that you can pry the light housing apart.

Then when you're done with all of your modifications, remove as much of the old sealant you can and then line the edges of the housing with the new sealant. Heat it up like before and compress it back together.

u/Ballaholic09 · 1 pointr/MotorcyclePorn

LED headlight bracket

LED Headlights

Auxillary Light LED

Integrated Tail Light

Bar End Mirrors

Radiator Guard

Rear Swingarm Spools

Mirror Mount Block off

Frame Sliders
This company sells a larger set of spools & sliders that is great!

CS Escapamentos Exhaust

Wind Screen

Levers

Block off plate substitute this is for when you get a full exhaust, youtube "block off plates z900" for more info
The prices all vary and there's PLENTY of options elsewhere. I just happened to get these over time. I also bought an engine guard/cage on Amazon but never could get it to fit properly.

u/Miguel30Locs · 1 pointr/Lexus

https://bulbfacts.com
YouTube Channel

I searched on YouTube for appropriate LEDs for reflectors for my old Toyota Camry. I found this reviewer that does extensive labs tests on various LED kits from Amazon for both reflector and projector housings.

I bought TechMax LED for $35 I think. They are bright, white and out classes any halogen I used and it didn't blind oncoming traffic since it's beam pattern sticks similar to halogen like BulbFacts states. I transfered those to my fog lights on my new Lexus.

For the projector headlights I bought the Katana LEDS since it provides the widest range for LED in a projector. I believe another LED outclasses it for distance at the cost of some side visibility. But I live mostly in the city so I prefer side visibility.

You will need a little bracket for the headlights. These are the ones I bought in order to keep the LED in place.

And a dust cover. There's one that's inverted on Amazon that's highly rated.

Which car do you have ?

u/HaiImBRIAN · 1 pointr/prius

I was in the same boat and waited just as long. I wish I took a before shot. I highly recommend adding a clear coat or else it will yellow again. https://www.amazon.com/3M-Quick-Headlight-Clear-39173/dp/B079QL8BYK/ref=sr_1_3?keywords=3m+clear+coat+headlight&qid=1559064919&s=gateway&sr=8-3

u/tehmobius · 1 pointr/ToyotaPickup

I personally hate most of the ridiculous looking replacement lights, but I don't think these look cheesy at all in person. Performance wise it is 100% worth it. The amount of light these new LEDs put out is fantastic.

Just be aware that due to the way the wiring is set up on our trucks, you will probably have to get an adapter wiring harness. Overall it was about $100 for everything.

Harness Link

Lights

Here's a picture from u/carriemcbride628
https://i.redd.it/u1zqf3mt6kc31.jpg


If you want any more info or pictures let me know.

u/RheaTheTall · 0 pointsr/Damnthatsinteresting
u/remembertosmilebot · 0 pointsr/AutoDetailing

Did you know Amazon will donate a portion of every purchase if you shop by going to smile.amazon.com instead? Over $50,000,000 has been raised for charity - all you need to do is change the URL!

Here are your smile-ified links:

https://smile.amazon.com/Meguiars-G17804-Clear-Headlight-Coating/dp/B01M4RVVX6/ref=sr_1_1

---

Never forget to smile again | ^^i'm ^^a ^^friendly bot