Best heat press machines & accessories according to redditors

We found 43 Reddit comments discussing the best heat press machines & accessories. We ranked the 27 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Subcategories:

Heat press machines
Heat press parts & accessories

Top Reddit comments about Heat Press Machines & Accessories:

u/subburban · 7 pointsr/cricut

The easy press actually isn’t a heat press. It’s just a large, square iron. In order to apply HTV properly, you need heat but most importantly pressure to get the correct application. A heat press basically warms up the glue but doesn’t offer enough pressure to get desired results. In my opinion, an easy press certainly does the trick for personal use, but if you want to get into selling, or really want to step up your game, a heat press will be great for you, too! With that said, I have this one:

Transfer Crafts T-Shirt Heat Press & Digital Sublimation Machine (9 x 12) https://www.amazon.com/dp/B07DNKBLKW/ref=cm_sw_r_cp_api_i_DtQRCbDQV1JB2

I love it!

u/peteymack · 3 pointsr/HomeImprovement

bought the hardware thru amazon for around $120 (very solid steel product) and built the door with some beetle kill pine tongue and groove. hit the studs or screw in a ledger board. we're gonna do the same thing for the main bathroom off the kitchen using the same door with glass panel. here's the hardware: http://www.amazon.com/Country-Coffee-Sliding-Hardware-Antique/dp/B00G2PO0T4/ref=sr_1_1?s=hardware&ie=UTF8&qid=1426730114&sr=1-1&keywords=barn+door+hardware

u/Jack_VITH · 3 pointsr/CannabisExtracts

The point is, the guy is saying build a risin press for 100bucks. Very few people that are looking to make a rosin press will have the suitable fruit press so for them, this is a waste of money.

Straighteners may hold up under hand pressure but once you start throwing extra weight in, they wont last long.

This is a more worthwhile investment of your time.

It's not great but it will put a lot more weed through it than the thing being built in the video.

https://www.amazon.com/Vanell-Machine-controller-Transfer-Sublimation/dp/B07RW9K5XT/ref=mp_s_a_1_17?keywords=rosin+press&qid=1568218841&s=gateway&sr=8-17

u/dabndan92 · 2 pointsr/rosin

3 Ton Hydraulic Jack Heat Press - dp-bj3t33-3x3 Inch Anodized Heat Press Plates - 500 Watts - Dual Heating Machine - Accurate Temp Detected https://www.amazon.com/dp/B07KQ387F3/ref=cm_sw_r_cp_api_i_zziQDbHMZNM87 Save your money and frustration

u/Cyrax89721 · 2 pointsr/RoomPorn

You can get a modern barn door hardware kit for less than $100.

http://www.amazon.com/TCBunny-Country-Sliding-Hardware-Antique/dp/B00G2PO0T4

u/FoxMaverick · 2 pointsr/VinylCutters

I bought a 9x12 Fancierstudio press from amazon as my first heat press which has been great but it's too small. I regret being impatient and not waiting until I could get a 15x15 which was the recommended size on most sites I researched. Other than that size issue I quite like it. The price was good and it heats up in a decent amount of time. Heat seems even from the stuff I've pressed but I've never checked it with a thermometer. When I upgrade in size I'm definitely going to try and stick with fancierstudio.

u/TheAtomicOwl · 2 pointsr/rosin

3x7 Inch DIY Caged Heat Press Plates Kit | dp-rp37 | Dual Heating Plates | Pair It with 10-20 Ton H-Frame Hydraulic Press https://www.amazon.ca/dp/B07KM1VGQ4/ref=cm_sw_r_cp_apa_i_Vnp1CbJTVPCK1

Tuopuke 3x5" Caged Cube Kits with Dual Solid 6061 Plates in Heat Cube, Dual Heaters, Dual Temp Sensors, Temperature Control Box https://www.amazon.ca/dp/B07N2DPMDK/ref=cm_sw_r_cp_apa_i_Lop1Cb0RZPYT5

Tuopuke 3x5'' Solid Heat Plate Kits with Dual Plates, Dual Heaters, Dual Temp Sensors, Temperature Control Box - Pair with A or H Hydraulic Press https://www.amazon.ca/dp/B07N1HVZNK/ref=cm_sw_r_cp_apa_i_mpp1CbH9CT2ZJ

u/leo-theleopard · 2 pointsr/rosin

Dabpress 3-ton is a way better choice imo.

It’s also available on amazon prime.

u/ArkadyBogdanov · 2 pointsr/rosin

https://www.amazon.com/4-7x4-7inch-Elements-Swing-Arm-Multifunctional-T-Shirts/dp/B07LCJ73YP/ref=sr_1_13?ie=UTF8&qid=1550962145&sr=8-13&keywords=rosin+press


I bought this press, and with a welder, 6 bucks in metal, and a spare bottle jack I made this.
https://www.imgur.com/a/S1CTSvW

Or you can buy the premade one for about 100 dollars more.
https://www.amazon.com/Hydraulic-dp-bj3t33-Anodized-Accurate-Detected/dp/B07KQ387F3/ref=sr_1_3?ie=UTF8&qid=1550962145&sr=8-3&keywords=rosin+press



Also I want to add that with max pressure on the hand press, vs max pressure on the bottle jack, the bottle jack version is yielding on average of 5x more oil. Hand presses are complete junk.

u/Fungnificent · 2 pointsr/BubbleHash

t-shirt press

$120

Not enough pressure for rosin, but slap your bubbly in some parchment and this'll do what you want.

https://www.amazon.com/Transfer-Crafts-T-Shirt-Digital-Sublimation/dp/B07DNKBLKW/ref=zg_bs_8090950011_13?_encoding=UTF8&psc=1&refRID=198WQ5ZG13753DC8MMVF


Start low, work your way up in pressure and temp until you find your sweet spot for hashpressing.
A few folds and presses and you'll be good to go!

u/PublicMemes · 2 pointsr/Mario

No problem! It’s quite simple, just takes a little bit of patience.

So first, we would make our design in Photoshop. Once we finished, we would print it out, then place it on one of these coasters that are specially coated for this type of printing. Finally, we would use a Dye Sublimation Heat Press to print the ink! It basically just heats the ink until it transfers on to another surface.

Here’s a link to the press: https://www.amazon.com/PowerPress-HPM-1515-BK-Industrial-Quality-Digital-Sublimation/dp/B0773Y1TNX/ref=asc_df_B0773Y1TNX/?tag=hyprod-20&linkCode=df0&hvadid=242004651088&hvpos=1o4&hvnetw=g&hvrand=3167507526720360267&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9012090&hvtargid=pla-449292883374&psc=1

I appreciate your curiosity, and thanks again!

u/chipotlemcnuggies · 1 pointr/cricut

For iron on, I like Siser Easyweed. Cuts really well on my Cricut Explore Air and like the name suggests, really easy to weed. If you want good results that last, you really should get a real heat press and not use a home iron. The key is that the heat press applies a LOT of pressure evenly, you can't do this with a home iron or even a Cricut press. It's not terribly expensive as you might imagine, this is the one I have: https://www.amazon.com/PowerPress-HPM-1515-BK-Industrial-Quality-Digital-Sublimation/dp/B0773Y1TNX/ref=sr_1_4?ie=UTF8&qid=1537937194&sr=8-4&keywords=heat+press

If you want it for vinyl stickers than Oracal outdoor vinyl (651 or 751) is most popular choice for something that lasts. (Application is also very important, if you don't apply it properly then even the best vinyl is not going to stick and stay over time)

u/ZuesAgeddon · 1 pointr/vegastrees

people are loving this press from Amazon.


I bought mine from this dude over 2 years ago, still running strong and his current work is better and cheaper. I drove down to Cali and picked it up from him. Good guy.

u/glockessin · 1 pointr/rosin
u/CricutMakerEQ · 1 pointr/cricut

I got this one and it works great. It takes some space but I can just set it under my craft table when I’m not using it.

F2C Pro 5 in 1 Combo Heat Press Machine T-Shirt Hat Cap Mug Plate Digital Transfer Sublimation Machine New Black (5 in 1 Swing Away) https://www.amazon.com/dp/B07L6CMXYK/ref=cm_sw_r_cp_api_i_lPd1DbJXE8A8Q

u/lunaticfringe80 · 1 pointr/rosin

https://www.baileigh.com/hydraulic-shop-press-hsp-10h

paired with

https://www.amazon.com/dp/B07KR54L16

I don't believe either of the ones you suggested have a pressure gauge. IMO it's rather important to have one to do quality presses.

u/Fbho420 · 1 pointr/rosin

This!

I also use 2x? And cut them to size. The BTS pre press was such a good investment. I have 2x4 bags I'm finishing and 2x8 on deck.

Edit: here's a link to the one i use

Cylinder Pre Press Mold | dp-pm3015r | Made of Anodized Aluminum | Pair It with 2x4 Inch Filter Bag https://www.amazon.com/dp/B07KR54D3M/ref=cm_sw_r_cp_apa_i_6gfZCbYA1M9WC

u/fiftythree33 · 1 pointr/rosin

After a couple days looking for the best deal I settled on this over the one you linked. It had a 20 off coupon a couple days ago... Dabpress 3x5 on Amazon

u/Rockin13j · 1 pointr/rosin

Upgraded 3x5 Inch DIY Uncaged Heat Press Plates Kit - dp-rp35 - Dual Heating Plates - Bottom Plate Holder Attached - Pair It with 10-12 Ton Hydraulic Press https://www.amazon.com/dp/B07KR4MNMB/ref=cm_sw_r_cp_apa_i_ZeLPDb78NJ0XA

u/waiting-on-one-day · 1 pointr/cricut

Fancierstudio Heat Press Heat Press Swing Away Heat Press 9"x12" Coated with Sheet Sublimation heat press Rhinestone Heat Press 9x12 GB https://www.amazon.com/dp/B01K3EXZF4/ref=cm_sw_r_cp_api_s70TBbCBHQSN9

I bought this one (cheaper than the easypress) and it’s amazing. A little bit of a learning curve, but it is amazingly easier!! And I feel like they came out much better than when I used just an iron.

u/tourthevoid · 1 pointr/rosin

Dulytek DM800 Personal Heat Press - Dual Aluminum Plates with Heat Insulators - Digital Control Panel - Portable, Sturdy, Efficient - 2019 Version https://www.amazon.com/dp/B07JMYBLPF/ref=cm_sw_r_cp_api_i_6.frDbG464BS3

u/Kinickie · 1 pointr/vinyl

I've actually had success in fixing warped records and jackets using one of these: https://www.amazon.com/Cricut-EasyPress-2-12x10-Inches/dp/B07G4V5PGJ/. The temp goes down low enough that you're not going to melt the record if you let it sit for 10-15 seconds.

My process is: Clean the record and place on hard, flat surface. Cover with parchment paper (NOT WAX PAPER), and iron needed areas. Immediately place flat heavy object on top of warm record until cool. Repeat as necessary to remove warping.

u/bvanasten3 · 0 pointsr/rosin

Small Portable Heat Press Machine - Dual 3x5 Inches Heated Platens - 10 Ton Hydraulic Cylinder Attached - No Pump Included https://www.amazon.com/dp/B07KR47Z2V/ref=cm_sw_r_cp_api_i_hFU2Db9PXWSK5 like this?

Do you have one? Seems it requires an extra $120 pump part