Best quilting supplies according to redditors
We found 229 Reddit comments discussing the best quilting supplies. We ranked the 118 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 229 Reddit comments discussing the best quilting supplies. We ranked the 118 resulting products by number of redditors who mentioned them. Here are the top 20.
https://www.amazon.com/X-Acto-X7761-Self-healing-cutting-measuring/dp/B0013CKM2A Here's a tiny one from a well known hobby company. So, way more expensive than one from a hardware store.
To solve the pricking yourself with pins problem-- try sewing clips! I bought these from Amazon and I think they're great. I find pinning stuff can sometimes distort the fabric, and you can't pin some fabrics because it leaves holes. They don't totally replace pins since you can only work from the edges with these, but they are really nice regardless!
Might be easier to just get a perforation cutter like this or this, then she can make any page tearable as she likes.
>brushes
If you use GW brushes, get the Standard, Fine Detail, and Wash brushes. These give you a good starting point for most of the stuff you'll be doing. Otherwise you'll want to find similar brushes in other ranges (Windsor & Newton make good brushes). If you go with third-party brushes I think the sizes you'll want are 1, 0, & 3/0.
>mats,
You can get any sort of sewing mat, where it's basically just a piece of rubber you lay on the table. Joann's Fabrics or any sort of sewing store should have this. Here's one I found on Amazon.
>thinners
The paint you're working with is water based, so water will work as a thinner. If you decide to airbrush things that will change what you need but for now, build a wet palette.
>cutters
Try these
>etc
You'll need some glue at the very least. You might also want some helping hands to hold things while you paint them/glue them together.
>is there a site that tells you what colours you need to paint certain colour styles?
I'm not aware of any one site as a catch-all for painting any scheme, but googling things led me to this site that goes into detail about painting Space Wolves. You could also consider this video from Games Workshop where they go through the steps of painting the model.
As for the paints themselves, I'd recommend working with the Vallejo Game Color paint range. They come pre-thinned (extremely helpful for new painters) and convert to Games Workshop colors pretty easily.
Some more hobby stuff to help you get started:
Zenithal Priming
Airbrushing
Object Source Lighting
---
Section 1: Tools
---
Note: Just because it is more expensive doesn't mean it is better. You could get by just fine with the "cheaper" options.
---
| Tool | Required vs. Optional | Use | Notes | Price & Link |
|:---|:---:|:---|:---|:---:|:---:|
| Tandy Wholesale Membership | O | Allows you to get better pricing at Tandy. | This is definitely optional. Items will cost slightly more without it OR if you have a tax ID you can get the membership with better pricing for free. | $35 / Free|
| Awl Haft | R | The handle which will hold your blade. | This particular haft allows for different blades to be added or removed with ease. | $16 / $35|
| Diamond Awl Blade| R | This is the blade used for piercing the holes in your projects.| This goes in the awl haft.| $4.80 / $28
| Channel Groover | R | Used to measure and gouge channels where your thread will lay. | Some say gouging a channel is optional however I find it to be required. It further protects your thread from damage. | $16 / $80 |
| Overstitch Wheel | R | Marks where you will punch your holes. | This particular overstitch wheel is a few dollars more than the versions that only offer one wheel. | $24 / $225 |
| Edge Beveler | R | Used to bevel and round off the edges of your project prior to burnishing. | Sizes vary. The smaller the number, the smaller the round edge. | $12 / $55 |
| Adhesive Glue | O | Used to hold your pieces of leather together prior to piercing the holes. | Some people prefer binder clips instead of glue. I've found that the clips end up making marks on my projects so I've always stuck with glue. | $6 / $30 |
| Gum Tragacanth | R | Used as a burnishing agent for your edges.| Some people use saddle soap. I prefer gum trag.| $6.40 / $21|
| Harness Needles | R | Used in combination with the thread for your projects. | Avoid the stitching needles. They break very easily.| $5.99 / $7.50 |
| Xacto Blade | R | Used for cutting projects. | You may have one of these at home already. Be ready to have replacement blades handy ($21.95) | $2.49 / $50 |
| Self-Healing Cutting Mat | R | Used for cutting your leather projects.| You may have one of these at home already. If so, you can obviously use that.| $14.73 / $50.80 |
| Cork-backed Ruler| R | Used for cutting straight lines.| I highly recommend the cork-backed version. It will save from accidental cuts/slips.| $4.80 / $14 |
| Burnishing Tool | R | Used in combination with the gum tragacanth to get a good burnish.| A good piece of canvas can be used as well. | $8.99 / $80 + $99|
| Sanding Tool| O | Used to sand down the edges prior to burnishing.| You might have sandpaper at home. Feel free to use that too.| $7.30 / $0 with dremel|
| Steel Square | O | Used for creating nice, even squares/rectangles for projects. | Learn to use this correctly!| $8 / $14|
| Thread Cutters | O | Use these for cutting your thread in the hard to reach places without running the risk of damaging your project. | Scissors work for cutting thread and the xacto blade can work for cutting thread inside your projects -- just be careful! | $3.95 / $39 |
| Maul | O | Used for end punches, rivets, snaps, chisels, or irons. | You really only need one of these if you are planning on doing any of the activities mentioned previously. | $20 / $55 |
| Pricking Iron/Chisel | O | Use these to mark or punch your holes instead of an overstitch wheel and awl. I prefer using the overstitch wheel and awl but others like the irons/chisels. | There is a big difference between irons vs. chisels, diamond vs. lacing. They all produce different results. Definitely ask before purchasing! The ones I linked are very different.| $12 / $259|
| Creaser | O | Used for decorative creases on things like card slots. | Definitely optional and definitely personal preference. | $14.40 / $72 |
| Wax | O | Used for burnishing. Gives the edges a nice seal. | The $10 is my top secret wax I use. I bought a bunch on sale for $5 and it is fantastic. | $4 / $10|
---
I have this and I LOVE IT
https://www.amazon.com/GONCHAROFF-EMBROIDERY-ORGANIC-COMPLETE-TAPESTRY/dp/B01CMFSGU6/ref=sr_1_11?crid=3AQZXU38ELK7G&keywords=scroll+frame&qid=1570394420&s=arts-crafts&sprefix=scroll+frame%2Cgarden%2C203&sr=1-11
I can easily adjust the legs, and it's easy to switch frames, too. Also, I really like the clamp system for holding the fabric to the frame. No taping, no stitiching, just clamp it in like you would with a q-snap. It has lots of great reviews, and I"m one of them!
I think everyone in the entire world uses this one from amazon:
https://smile.amazon.com/dp/B00RO1CD9O/ref=cm_sw_r_cp_apa_i_Xu4ODbQ3TTHXK
One side is imperial and the other is heretic. I mean Metric.
It's this one but it isn't currently available through Amazon 😿
They do have a slightly different one available, it just has less mobility.
https://www.amazon.com/gp/product/B0027RN0JW/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
Thanks! It's just a cutting mat, this one specifically is this: https://www.amazon.com/Dahle-Vantage-Self-Healing-Cutting-12-Inch/dp/B0027RN0JW?th=1
I'm basically using it to have a fully level surface with no gaps on my desk I made with 2x6" planks
What shape of hole? I typically just cut through it with my knife like any other cut and pop it out like a token, but for circles that probably isn't doable.
I'd try something like this, but I've never used one myself.
It all depends on what type of builder/crafter you want to get into. Buying all the "machines" and tools for someone that would be a foamsmith but you're really a needlework kind of person makes it a potential waste of money and time (and vice versa).
IF you want to get into an overall crafting/building in general, here are the tools and materials I've gathered for my workshop:
I'm gonna put the word **Optional** for the items that are not completely necessary for first time builders, but definitely worth while down the road.
Here are some helpful options for your search for EVA foam. Hopefully one of the stores I list here will be some-what local for you. Home Depot, Lowes, 5 Below, BJ's, Costco, Walmart, & Harbor Freight all carry the EVA (floor mat) foam. I have personally purchased and used foam from all of these locations.
Helpful links from the masters: Evil Ted Smith , Punished Props , Odin Makes , KamuiCosplay.
Hope this helps.
*note some prices are subject to change*
First I'll list what I bought and then I'll discuss what I have or what I'd have done differently.
Not listed are an xacto blade/utility knife, cork-backed ruler, and steel square. These were purchased at Harbor Freight.
Awl Haft
Diamond Awl Blade
The awl haft and diamond blade (E42) are great. I like the combo I bought. The handle has a chuck instead of some I saw which need the blade pressed in to the chuck.
Channel Groover
The channel groover I bought is nice. The chuck, similar to the awl haft, is very convenient for quick adjustments.
Overstitch Wheel
Doing it again, I probably would have bought some diamond chisels over the overstitch wheel, but so far it's worked alright. I will be buying the chisels eventually.
Edge Beveling Kit
I had no idea what edge beveler to buy with so many sizes and never having touched leather, so I'm really happy with the one I bought. It comes with 5 sizes.
Harness Needles
I bought 3 sizes of harness needles. Probably overkill but they were $3 a pack and I didn't know what size I needed. I've been using the medium ones and they are working well with the thread I got.
Cutting Mat
The cutting mat is nice. It's a bit thicker than the ones I found locally at Michaels.
Lacing Pony
The lacing pony is probably my biggest regret that I was forced to buy. I don't have access to any woodworking tools so I was stuck purchasing one. I should have had a coworker do it for me in his shop at 1/5 of the cost. It comes in two pieces and the holes in mine didn't line up at all. I ended up having to drill a hole for the screw.
Art of Hand Sewing
The book comes highly recommended from everyone. I've flipped through it but I learned my basic technique from youtube videos. As I try to do more I'm sure I'll reference it.
Thread
I bought .035" waxed cord from Maine Thread. I have nothing to compare it to but it seems to work okay.
Leather
And finally the leather. I'm still not sure if I made the right purchase, although buying a shoulder of leather seems to be a popular beginner suggestion. Already I'd like to have more variety, but I think I'm going to a Tandy Leather this weekend so maybe I'll pick up some other random stuff.
Things I didn't buy that I should have:
Contact Cement
Gum Trag
Burnishing Tool
Hammer/Maul
Leather finish
I actually made a decent stitch I was happy with on my second try. I didn't buy these items because I planned on doing lots of practice on scraps but because I feel good about my initial work I'd like to try to make something. Without those few items I'm kinda stuck for the moment.
https://www.amazon.com/OLFA-9911-Compass-Circle-Cutter/dp/B000BK7NWC
Honestly, I rarely bother with masks, even on tanks.
For tanks, you can also use either purpose designed or architectural/drafting circle templates like these as a spraying stencil.
https://www.amazon.com/Helix-Small-Circle-Template-37168/dp/B00AETPZFW/ref=sr_1_1?ie=UTF8&qid=1441141539&sr=8-1&keywords=circle+template
But honestly, in most instances I just spray the center/hub and then finish off with a brush. Faster, even if more tedious.
A summary of most of the above is further provided here.
http://www.scalemodelguide.com/painting-weathering/painting-guide/paint-rubber-rims-tank-wheels/
Really not hard at all with a compass cutter or something similar. I think on my old kit I actually used a legit drawing compas with a razor blade clamped into it or something. Just measure out the diameter/radius, pick your center and go. You can buy rings that snap in to make it look nice and give it strength: https://www.sweetwater.com/store/detail/BDO6BK?gclid=EAIaIQobChMIz4TO0a6m2QIVUbbACh2vqg0TEAQYASABEgLxqPD_BwE
zip ties, - skip the heat shrink for the esc's around the arms. Just zip tie them.
LOTS of nylon spacers - https://www.amazon.com/gp/product/B013G1QSNW/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
solder braid
Hex drivers - https://www.amazon.com/PIXNOR-Hexagonal-Driver-Screwdrivers-Helicopter/dp/B00QLZGRHS/ref=sr_1_5?s=industrial&ie=UTF8&qid=1467916704&sr=1-5&keywords=hex+driver
sma pigtails - https://www.amazon.com/gp/product/B01DNMAEJS/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
rubbing alcohol(gets off flux)
90 degree single pin headers - https://www.amazon.com/2-54mm-40-Pin-Header-Connector-Length/dp/B00R1LQ3FC/ref=sr_1_1?ie=UTF8&qid=1467916531&sr=8-1&keywords=90+degree+single+pin+headers
mat - https://www.amazon.com/gp/product/B00P6KPKAE/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
wire cutters - https://www.amazon.com/gp/product/B00FZPDG1K/ref=oh_aui_detailpage_o09_s00?ie=UTF8&psc=1
Thanks! It's the Alvin 18x24" self-healing: https://www.amazon.com/dp/B0025189VE/
Fabric scissors are always good gifts
Quilt clips
Chalk pens
Also I think most quilters would love charm packs and jellyrolls
Amazon has them.
ZERRO Self Healing Cutting Mat https://www.amazon.com/dp/B06Y5MW6G3/ref=cm_sw_r_cp_apa_i_vISyCb7NGG8VV
Circle rotary cutter. Easy to use and works well. OLFA Rotary Circle Cutter https://www.amazon.com/dp/B001CEAMCY/ref=cm_sw_r_cp_apa_BTUCzbJDR0X1Q
This is the one I got that /u/chasem13 had for his foamcore the other week. It definitely takes multiple passes, easiest if the last one is from the back side but it works well.
Like this?
DAFA Professional 24" x 18" Self-Healing, Double-Sided Cutting Mat, Rotary Blade Compatible, (36x24), (24x18), (18x12), (12x9) Sizes, for Sewing, Quilting, Arts & Crafts https://www.amazon.com/dp/B00P6KPKAE/ref=cm_sw_r_cp_apa_i_aAgPDbA0QGA3B
Pic shows metric
For tools (for example, to make a wallet), you would need... anything missing?
Wooden slicker for burnishing (http://www.amazon.com/gp/product/B0048FM2OU?psc=1&redirect=true&ref_=ox_sc_sfl_title_27&smid=A3NY6IRPSQ8J63)
self-healing mat (http://www.amazon.com/gp/product/B0006SDOFO?keywords=self%20healing%20mat&qid=1449180954&ref_=sr_1_8&sr=8-8)
Cement (http://www.amazon.com/Barge-Cement-Rubber-Leather-Glass/dp/B002JL2ZHE/ref=sr_1_2?ie=UTF8&qid=1449180993&sr=8-2&keywords=leather+contact+cement)
Edge dye (http://www.amazon.com/Tandy-Leather-Eco-flo-Professional-Dressing/dp/B00LKMAJQW/ref=sr_1_13?ie=UTF8&qid=1449181034&sr=8-13&keywords=leather+edge+dye)
Sand paper
grover for making stitch grooves (http://www.amazon.com/gp/product/B00OHAHICM?keywords=leather%20edge%20beveler&psc=1&qid=1449180851&ref_=sr_1_1&sr=8-1-spons)
beveler (http://www.amazon.com/gp/product/B00430GAS4?psc=1&redirect=true&ref_=ox_sc_sfl_title_30&smid=ATVPDKIKX0DER)
awl/chisel for making stitch holes (http://www.amazon.com/gp/product/B00CBRVKOK?psc=1&redirect=true&ref_=ox_sc_sfl_title_31&smid=A1EX7LU0M6LM21 http://www.amazon.com/gp/product/B0036LNXEA?psc=1&redirect=true&ref_=ox_sc_sfl_title_29&smid=A2UDNPGKURPVSY)
needles for stitching and thread (http://www.amazon.com/gp/product/B00114RBSI?psc=1&redirect=true&ref_=ox_sc_sfl_title_26&smid=ATVPDKIKX0DER)
Anything else?
Looks like a cutting mat. I’ve got a great big one that covers my whole desk. Black on one side, and green on the other. They work really well as basic worktable surfaces.
US Art Supply 24" x 36" GREEN/BLACK Professional Self Healing 5-Ply Double Sided Durable Non-Slip PVC Cutting Mat Great for Scrapbooking, Quilting, Sewing and all Arts & Crafts Projects https://www.amazon.com/dp/B00L5I8RTW/ref=cm_sw_r_cp_api_i_JHMXCbHCH132P
http://www.amazon.com/gp/product/B0025189VE/ref=as_li_ss_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B0025189VE&linkCode=as2&tag=goosgunblo-20
https://www.amazon.com/gp/product/B0027ROZ9G/
It is a Zerro 34x26 cutting mat
https://www.amazon.com/gp/product/B06Y5MW6G3/ref=oh_aui_detailpage_o03_s01?ie=UTF8&psc=1
Here is a photo I did when I got it without anything on it. Fits my desk perfectly.
Reddit post
Have you used the homemade baste? I was thinking of using that between the extra layer and blocks then again between the regular layers.
The store bought stuff is pricey.
I also received a box of these clip things along with natural batting as a gift. Hopefully they'll help me out:
MumCraft Multipurpose Sewing Clips with Tin Box Package, Assorted Colors, Pack of 100 https://www.amazon.com/dp/B001PNIWT2?ref=yo_pop_ma_swf
I used this chipboard (ordered from that exact amazon listing). It's 2mm thick. I printed the labels out on a laser printer, used 3m super 77 spray adhesive to glue the paper onto the chipboard, then used a rotary cutter, metal ruler, and self-healing cutting mat to cut the dividers to size.
I had all of this stuff around the house - I've PnP'd several games, so none of this stuff is new to me.
Maybe this?
You could just buy your favorite one without perforations and buy something like this: amazon "wheel cutter perforation" and perhaps a metal ruler. With them you can make your own perforated pages.
I used this. Took a few tries on scrap foamcore to get the hang of it, but really happy in the end.
OLFA 9911 CMP-1 Compass Circle Cutter https://www.amazon.com/dp/B000BK7NWC/ref=cm_sw_r_cp_api_i_n3nwDbMEMY3MJ
Measure and draw would work too! Actually that's what I did for the roundels -- found comparable sized circle shapes around the bench (bottle cap, pencil eraser, etc) and used them to trace circles onto the tape to cut out the roundel stencils. Figured out later that a compass cutter probably would have saved a lot of time and been more precise.
It's not cheap really, but you could use a circle cutter to make it circular. Just practice on something else before trying to do it.
It's Hobbico Builder's Cutting Mat.
Don't bother. Unless you are trying, actually setting fire to a wooden countertop with a soldering iron is pretty damn hard. You would have to jam it into a heap of shavings to light a fire with it. If you really want to, you can get a mat like this.
Its this self healing cutting mat
Those are cutting mat, used to protect the surface of the table from your hobby knife. I bought mine from amazon.
Alternatively, you can use the shape on the mat to cut masking tape for more advanced painting purposes.
It is a Fiskars 45mm Contour Rotary Cutter. $10 at Amazon or Walmart. I use it on a X-acto selfhealing mat. You have to make sure you get the right one that does not have ink that rubs off easily. A labmate ordered a replacement that smudged all over some plates. Here is the exact model I have: X7761 12x18in
You're doing way better than you think you are!
I'm probably gonna repeat things other people said but here we go:
I'm also a beginner so message me if you want a quilting buddy!!! =D These are some pinwheels I made like 2 weeks ago! =P
​
PS: This is your first block ever and you didn't chose the easiest one soooo GO YOU!!!!!!!!!!!!!!
That's way expensive. You can pick these up at a craft store like Michael's or Joann fabrics for way less. Here they are on amazon for a quarter of the price.
Quilt basting gun. I am very careful as the needle is somewhat large, but I love this darn thing! AMRAM Quilting Quilter's Quilt Basting Gun Kit. Includes 3,000 Pcs 3/8" FINE Tacks (Red) and 5 FINE Needles. https://www.amazon.com/dp/B00SJG8GKS/ref=cm_sw_r_cp_api_i_6ZE7CbR0Y30EY
RAGNAROS Multipurpose Sewing Clips For Quilting Crafting With Tin Box Assorted Colors 110 Pack 2 Size100 Small 10 Large https://www.amazon.com/dp/B06XCGSY17/ref=cm_sw_r_cp_api_dRwaCbK4XREMW
Clips like these, I don’t know the brand or anything, just as an example
Look for a self-healing cutting mat such as this https://www.amazon.com/X-Acto-X7761-Self-healing-cutting-measuring/dp/B0013CKM2A
I've used one of these for years and it's great
Dahle Vantage 10673 Self-Healing Cutting Mat, 24"x36", 1/2" Grid, 5 Layers for Max Healing, Perfect for Cropping, Sewing, & Crafts, Black https://www.amazon.com/dp/B0027RN0JW/ref=cm_sw_r_cp_apa_2FfTAbRT9T7JM
In addition to whats listed here:
Self Healing Cutting Pad
Roll of paper towels
Exacto Knife with spare blades
Mini Files
Pin Vise (aka Mini Drill)
Good observation. This seems to be a standard work matt for doing electronics stuff, I picked mine up at my local hobby shop. Maybe something like this is what your looking for?
You can try one of those plastic cutting mats for sewing. One of these https://www.amazon.com/gp/aw/d/B00L5I8RTW/ref=zg_bs_262643011_13?ie=UTF8&psc=1&refRID=YMBFT6YKR9K9KT8FAF8H some of them are better quality than others, and they come in different sizes.
I roll out my smaller doughs on a silicone baking mat. This is the exact one I have, and I love it! https://www.amazon.com/gp/aw/d/B00IY1C7D0/ref=mp_s_a_1_13?ie=UTF8&qid=1511365887&sr=1-13&pi=AC_SX236_SY340_FMwebp_QL65
I'm not really "experienced," but I've made a couple. As far as I know, the best way to figure out how much foamcore you'll need is to plan out your insert before you start. Draw out all the pieces (with measurements), then figure out how they'll be laid out on the size of foamcore you can get, then add some extra in case you screw up (which, if you're anything like me, you will... several times).
As for tools - a utility knife with replaceable blades (and a whole lot of replacement blades), a self-healing cutting mat, an adjustable square, a metal ruler, some good glue, and something to help hold everything together (pins and/or ratchet clamps) are all good things to have on hand.
https://www.amazon.com/gp/aw/d/B01CMFSGU6?psc=1&ref=ppx_pop_mob_b_pd_title
It’s currently out of stock but I would grab one when it’s available again!
I wanted something I could easily move between rooms in my house, but would let me easily hide from company or cats.
The mat on top is glued down with spray photo glue so it could be removed later if desired (through some difficulty). The entire table is collapsible, I would need un-clamp the lamp and remove the shelved items.
Table - https://www.amazon.com/gp/product/B000NPON1Y
Lamp - https://www.amazon.com/gp/product/B01CHZLW5M
Mat - https://www.amazon.com/gp/product/B0027ROZ9G
i got these:
https://smile.amazon.com/gp/product/B06XCGSY17/
As far as I can tell, they are no different from the name brand ones.
Photoshop template, printed on normal paper and cut out with a circle cutter.
https://www.dropbox.com/s/4if60dn5an23tlk/Jar%20Labels.psd?dl=0
Circle cutter: https://www.amazon.com/gp/aw/d/B000BK7NWC
Hobbico Builder's Cutting Mat, 18x24 Inches https://www.amazon.com/dp/B0014VX88K/ref=cm_sw_r_cp_api_i_Os0rDb6G1PHT1
I’m using it as a buffer on an old glass computer table until I get a legit workbench. I’ve used it in the past for painting models and whatnot.
Make a circle with this first?
http://www.amazon.com/Olfa-194B-OLFA-perforation-cutter/dp/B001GLP39A/ref=sr_1_1?ie=UTF8&qid=1463807981&sr=8-1&keywords=perforator
I used this table and will end up supporting it on both sides with 9 cube shelves which gives a lot a storage. I have a 36 x 24 cutting mat. I read about someone using the cube shelves which makes the table about 36" high so I decided to try it, I like the height and I'm pretty short at just barely 5'4"
No ar15 pics? Hows that tekmat, is it basically just typical mousepad material?
I use one of these: http://www.amazon.com/Alvin-Professional-Cutting-Green-Black/dp/B0025189VE/ref=sr_1_3?ie=UTF8&qid=1393819838&sr=8-3&keywords=alvin+cutting+mat
The most standard ruler to start with is a 6"x24".
It will do almost all your cutting, and will adapt to a surprising amount of work.
This will be my next one (cause it is just that cool). But honestly, you have to be able to read measurements off of this. Omnigrid makes the easiest to read, but take a look at different ones and see what is good for YOU!
Florescent Green Ruler
​
No matter what ruler you get, you can always make them grippier! Try something like these:
Non Slip rings
​
This is my favorite mat. It has lasted over 20 years. It is thicker than other brands. (and cheaper!)
Alvin Mat
I believe I have finally decided on my first Gunpla, the HG Age II Magnum and want to make sure the items I have added to my Amazon cart are ideal or not for a beginner/future use for HG and MG kits. The list is as follows:
I know that this sub has a list of tools and tutorials, but because I'm trying to budget, I was thinking no more than $100 would be ideal for me to start with. Since I'm beginning with HG models, I don't think I need a full set of Gundam markers, but if it's needed/required/highly suggested, I might pick them up as well.
So I have read and seen that top coating and panel lining are essential for MG models to make them pop. Are they just as essential for HG model kits? Looking at pictures of the Age II Magnum I'm planning on getting from Amazon, it doesn't seem to have a lot of indents for panel lining. Of course, I could be wrong and be blind as a bat. If I don't do any sort of panel lining, is it still a good idea to add a top coat regardless?
Also, how soon can one get into MG kits? I was originally going to jump straight into either the MG GM Sniper II or the RX-78-2 Ver 3.0 but after doing some research over the past few days, I've decided I'll be doing a few HG's to begin with as I haven't built model kits since I was like 7 or 8 with my dad. I'm thinking after the Age II Magnum, I was thinking about getting either the HG Double O Diver or the HG 00 Shia Qan[T]. Maybe after I complete the 3 HG's I've listed, is it possible to jump to the the GM Sniper II?
TL;DR:
The glue would probably be overdoing it a bit, though it'd depend on the thickness/rigidity of the sheet.
Laser cutters are pretty special bits of equipment. A cheaper option may be to use a circle cutter like this one: https://www.amazon.com/OLFA-9911-Compass-Circle-Cutter/dp/B000BK7NWC/ref=mp_s_a_1_5?keywords=circle+cutter&qid=1569064971&s=gateway&sr=8-5
There are 42 reviews on this one and it’s the highest rated on amazon. Do you think this is a good stand?
GONCHAROFF EMBROIDERY FRAME DIANA FOR USE ON TABLE OR COUCH; MADE FROM ORGANIC BEECH, COMPLETE WITH TAPESTRY FRAME; 12X15,5 INCHES (30X40CM) - HANDS-FREE WITH https://www.amazon.com/dp/B01CMFSGU6/ref=cm_sw_r_cp_api_i_lY.CDbHZX6E5Q
Looks like a cutting mat. Think this is it!
Use a tagging gun, like this
Most people prime in white or black.
Cut mat
I agree with mr.godonut here. Also using a cutting mat has helped me.
I use an Olfa Circle Cutter if I want to make perfect circular paint masks. Otherwise, I mostly hand cut my masks for the sake of time.
Olfa Circle Cutter on Amazon
This is the tool I use, although it was only $9 when I bought it a couple years ago. It's a fine product, but idk if I'd spend more than $10 for it again. There are similar products on amazon.
It works well. When utilized with a straight edge, it produces a very professional perforation. I can perforate an entire Midori brand refill in ~4 passes w/ moderate to heavy pressure. It's another step in preping my Midori, but I would not call it tedious or troublesome at all.
The only drawback I've experienced is that it may work too well, in that if I keep a perforated page in the notebook and turn past it, the page folds at the perforation line and not at the natural fold of the refill. I used to worry that this would eventually result in one of these pages unintentionally falling out, but nowadays I leave a small section of the pages' top and bottom unperforated to ensure they stay in. It hasn't really been a problem, and I imagine that if you use a tool with wider spaced cutting sections, it would be different.
It's a cutting mat. Mine is this one:
https://www.amazon.com/OLFA-Double-Sided-Self-Healing-Rotary-Mat/dp/B0006SDOFO/ref=sr_1_1?ie=UTF8&qid=1498482827&sr=8-1&keywords=olfa+cutting+mat
Need it for model making. 24x36 is a little excessive even for me but running out of room on a long cut sucks. You can get them at most art stores or fabric stores in various sizes
Here is the exact same mat on amazon -> https://www.amazon.com/Hobbico-Builders-Cutting-18x24-Inches/dp/B0014VX88K
So originally, my thought was buying blank seal and send card stock (LCI Paper has blanks that are ready to print) and running them through a laser printer.
After talking with my friend, M, I made an Excel template (Download, and then zoom out til you can see it all!) to give her that kind of outlines it. I created a blank one you can download here. In my head, 1 pixel = 0.01 inch, so each row is .25" high, each column is 0.25" wide, with each square with a dotted outline is one square inch.
Using my Excel sheet mockup (and a bunch of Pinterest inspiration), M created our proofs for a digital printer she works with. Most printers should be able to at least print it, as the full size is 12.75" long by 6" wide, which would be 1 invite to 1 piece of legal sized cardstock. Ideally, they could cut it down to size, and then perforate and fold it for you, but worst case, that part can be done with a paper cutter, self healing mat, bone folder, and perforating tool (I really like this one, but definitely use a ruler or something to guide you as it's pretty easy to curve off track).
The more folds and perforations the printer does, the more expensive it gets, of course, but the design and printing are the hardest parts!
I have one that looks similar that is a self healing board. It's basically a rubber mat that you can use to line things up, cut things on etc. If you cut something on top of the board and leave a cut in the rubber, it will smooth itself out after a couple hours.
EDIT:
Link to a self healing mat on amazon: https://www.amazon.com/X-Acto-X7761-Self-healing-cutting-measuring/dp/B0013CKM2A
Well in all fairness, self healing cutting mats have been available for a good while, though I've only heard ones purposed for cutting paper / hobbyist purposes. Googling "self healing cutting mat" gives this amazon hit of a such product, for example.
And for the record, I am not recommending these for cooking use, I have no idea of their toxicity, I've just seen these around in offices I've worked in for at least a decade or so.
Dahle Vantage 10673 Self-Healing... https://www.amazon.com/dp/B0027RN0JW?ref=ppx_pop_mob_ap_share
You only need a cutting mat (I use this one), a decent knife (mine again) and a metal ruler. Some designs are intended to be assembled without glue, but some basic paper adhesive can be helpful anyway.
Patience is pretty important; sometimes I rush a cut and it ends up drifting away from the ruler, which has resulted in having to reprint something.
Just a standard Rotary Mat.. I’d like to get something different, but no gun cleaning mats I’ve found yet cover the surface area of that table (24 x 36 inches).
Here ya go
https://www.amazon.com/OLFA-Double-Sided-Self-Healing-Rotary-Mat/dp/B0006SDOFO/ref=mp_s_a_1_3?keywords=olfa+cutting+mat&qid=1572292687&sprefix=olfa+c&sr=8-3
Rotary cutter!!! All the way and for everything! I can't believe how much easier it is to cut all the different fabrics I use. Just roll along instead of dragging the x-acto. My mind way blown once I got the rotary. I almost never use my x-acto anymore. And pick up a big mat like 24x36" for $21 off amazon while your at it. It makes cutting larger projects so much more easier. I just upgraded form a small mat and wish I had so so long ago, especially since it was so cheap. Sorry I was late to the party, but I had to give my 2 cents...
Hey everyone!
I'm as new as it gets. So, I made a shopping list after doing some research on everything that I think I need to start. I'll place the links to all the items in the lines below. Everything is on Amazon because... well why not?
Gundam
Glue
Marker
Tweezers
Knife
Cutters
Mat
More Markers!
*Krylon Matte Finish
Am I missing anything?
I buy unperforated and perforate them myself.
https://www.amazon.com/gp/aw/d/B001GLP39A/ref=mp_s_a_1_1?qid=1466223469&sr=8-1&pi=SX200_QL40&keywords=perforator&dpPl=1&dpID=313G3JXy7RL&ref=plSrch
Hello everyone! I've been having a lot of fun with this latest project. I've learned a lot
10 . Hobby lobby has a 90 day return policy. So, after I ran out of floss, I went there, bought a whole handful of the same lot. What I don't use, I can return! As long as I don't put it on a bobbin. This way I make sure to get all I need in the same lot, but don't waste too much money
I think that is enough lessons for now. Hope everyone is having a great day.
Yeah, definitely. I got the Alvin 24"x18" mat and it's $17.66 and Amazon prime. I saw u/pexon had a huge one when he sent me photos of some cable ideas and thought it was perfect for keyboard stuff.
When I'm punching holes I currently use a piece of cardboard scrap underneath, but is it safe to do so on my cutting mat instead or will I ruin it? (I have this mat)
According to all the reviews, this is very common. And one reviewer even says they have had it for a whole year now and it still smells! I would take it back.
Source
Buy a cutting mat mate:
http://www.amazon.com/gp/product/B0025189VE/ref=as_li_ss_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B0025189VE&linkCode=as2&tag=goosgunblo-20
It'll stop your mother/girlfriend/wife from violently murdering you in your sleep for ruining a table.
Have you considered perforating the pages yourself with something like this? https://www.amazon.com/gp/aw/d/B001GLP39A
I have been buying the Dahle Vantage mats and they are outstanding. Thicker and more durable than my legit Olfa mats, no odor at all, ship flat instead of rolled, and crazy cheap. I was worried about the quality given the price, but I have been very impressed by them and now have like 8 different mats in 4 different sizes.
I have a simpler version of this, down to the visible brand markings. I bought it on amazon.com. Here's the link. I thought Etsy was for handmade goods, not wholesale.
Here's what I bought, comes in larger sizes as well. I soldered on it but its designed for cutting, if you were sloppy enough it might mar the surface.
or you could save $40
https://www.amazon.com/OLFA-9911-Compass-Circle-Cutter/dp/B000BK7NWC/ref=sr_1_fkmr0_1?ie=UTF8&qid=1543186319&sr=8-1-fkmr0&keywords=thunderline+circle+cutter