Best sewing machine accessories according to redditors

We found 115 Reddit comments discussing the best sewing machine accessories. We ranked the 88 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Subcategories:

Sewing machine attachments
Sewing machine carrying cases
Sewing machine parts
Sewing machine presser feet
Sewing machine oil

Top Reddit comments about Sewing Machine Accessories:

u/WoodenCyborg · 7 pointsr/rawdenim

I've been using this sewing machine ST371HD for about year and half now on denim repairs and alterations. It's held up like a champ considering how cheap it is. I'm looking to upgrade to a new machine(s) for top stitching and machine darning. I use the free arm feature a lot to get to place without busting too many seams. Anybody have any good suggestions? I'm open to new or used, consumer or industrial.

Edit: incase anyone else is interested. This cheap Darning foot made a huge difference in the quality and ease of my darning repairs.

u/aguywithadream56 · 6 pointsr/reloading

AOZBZ Sewing Machine Light Strip 11.8inch USB Dimmable LED Strip Lights with ON/Off Switch, 6500K Cold White (1 Set) https://www.amazon.com/dp/B07RM1DGT6/ref=cm_sw_r_cp_api_i_N0gvDbCNS5KPN

u/Gecko23 · 5 pointsr/3Dprinting

I use sewing machine oil, doesn't gum up, doesn't stink, pretty much ideal for these kinds of low load applications.

I might be mistaken, but I think my hair klippers came with plain old mineral oil, which probably would work the same, if it's not the same stuff anyways. lol

u/maggyruth · 4 pointsr/sewing

Presser foot. You need one with the shank. The set you linked to only has the soles, it appears.

Looks like a low shank machine, so something like this should work:

YEQIN Low Shank Zig Zag Sewing Machine Presser Foot with Low Shank Adaptor- Fits All Low Shank Singer, Brother, Babylock, Viking (Husky Series), Janome, Bernina, Kenmore, White https://www.amazon.com/dp/B07F12H8P2/ref=cm_sw_r_cp_api_i_v3rDDbATZVCD0

u/wedge_squadron · 3 pointsr/quilting

I bought a Juki TL 2200 QVP Mini a few months ago, and bought this foot online as it didn't come with a 1/4 foot without the guide:

https://www.amazon.com/Juki-Standard-Hinged-Quarter-Presser/dp/B079VVRXWX/ref=sr_1_10?ie=UTF8&qid=1539231980&sr=8-10&keywords=juki+1%2F4+inch+foot

I noticed that the needle seems to be rubbing the side of the foot, and when I put the presser foot down you can see that it's blocking half of the needle hole. My other feet don't do this. I also don't feel any resistance when I gently move the needle up and down with the flywheel but it looks bad to me so I haven't sewn with it at all. Is this as bad as it looks to me?

Could this be a defective foot? Would it be worth it to try and get a replacement?

u/king_jong_il · 3 pointsr/sewing

If you have a local sewing repair shop see if they have this oil because I love the spout. Whatever you do use sewing machine oil because other types can gum up machines over time. Also I don't know if your Pfaff is the same, but I recently came across a Pfaff 130 but in terrible shape. From what I've learned the zig-zag mechanism is prone to freezing up because of the tight manufacturing tolerances, even when stored in ideal conditions. If it is frozen you may want to take it somewhere and have them take a look at it.

u/IPL4YFORKEEPS · 3 pointsr/sewing

I think most of the one-step buttonhole feet will set you back $20+. But you can also use a [snap-on sliding foot] (http://www.amazon.com/Singer-Sliding-Buttonhole-Foot/dp/B008MNWMJY) or even a [slant shank open-toe buttonhole foot] (http://www.amazon.com/Slant-shank-Open-Buttonhole-Foot-11311/dp/B002F01QQU) The open toe foot will allow you to make manual buttonholes for much larger buttons than the one-step or sliding style.

u/jibbidibbi · 3 pointsr/quilting

oh hey also this doesn't fall under seam guides, but my stitch in the ditch game improved VASTLY with a joining foot. https://www.amazon.com/Distinctive-Joining-Stitch-Machine-Presser/dp/B003Q6O9BQ

you put the guide in the seam and it helps like a billion percent

u/sparks1990 · 3 pointsr/BuyItForLife

No way you'll ever repair that.

Buying a new belt would be much easier, but you can still replace the buckle if you want. You'll have to cut that stitching around the keeper to remove it. Then you need to punch a hole on either side of it and add some Chicago Screws. You can get those at pretty much any hardware store.

I'd add a drop of blue loctite or the screws will work themselves out over time. It won't look the best, but the screws will be covered by the belt when you wear it.

Depending on the belt width, a buckle will run you about $10 on Amazon.

u/portedtoreality · 2 pointsr/3Dprinting

I think the same machine oil you use for CNC will work, but I use sewing machine oil to lube the X and Y rods (couple drops) whenever they feel "dry" to the back of my finger:

https://www.amazon.com/4-oz-Sewing-Machine-Oil/dp/B000H8Q41Y

For Z-axis, I use PTFE synthetic grease (drops all along the Z axis) like this every... 6 months?:

https://www.amazon.com/Super-Lube-21030-Synthetic-Grease/dp/B000XBH9HI

Also, make sure the extruder gears aren't grinding/biting into the filament too much and getting filament poo poo buildup all over the gears.


Spare nozzle, hotend, thermistor (I've only had to replace a hotend once in 2 years and also because I made a dumb mistake).


Don't be afraid to ask for help when you aren't sure because if you screw up, you may damage your printer.

u/bda22 · 2 pointsr/vinyl

a small machine oil is what you want to look for.

like the stuff you use for a paper shredder, hair clippers, or sewing machine.

https://www.amazon.com/Sewing-Machine-Zoom-Spout-Oiler/dp/B079RMRZ8D/ref=sr_1_2?keywords=small+machine+oil&qid=1554237567&s=gateway&sr=8-2

u/gh0stwriter88 · 2 pointsr/Amd

https://www.amazon.com/Sewing-Machine-Zoom-Spout-Oiler/dp/B079RMRZ8D/ref=pd_lpo_sbs_60_t_2?_encoding=UTF8&psc=1&refRID=CJ2CAWNG3QY75HDGTNB7

This is what we always used... the spout is handy in some situations too, we had this air conditioner that required periodic oiling or the fan bearings would start howling. We've had the same bottle of it for some 20 years lol.

u/CiderApe · 2 pointsr/sewing

My dad got me an old sewing machine from one of his friends. It is a Montgomery Ward sewing machine (it doesnt say what type.) The sewing machine works perfectly when plugged in and so does the peddle. But my mom said she thinks the presser is missing for the machine. Is it? And if it is would me buying this fic my problem?--> https://www.amazon.com/Machine-Presser-Babylock-Simplicity-Machines/dp/B01MCYWLUK/ref=redir_mobile_desktop?_encoding=UTF8&fbclid=IwAR0ZhSMtNaPRjOUI0K27vkch6IImEtC4y7jt3tcqT7zDhMh1Bb0To3lTMEI&psc=1&ref_=ox_sc_saved_image_9&smid=A34788DK4L5DWV

u/Josh_Your_IT_Guy · 2 pointsr/HelpMeFind

Similar to this? LNKA 5pieces Brand New Sewing Machine Screwdriver Home Sewing Machine Repairing Tool https://www.amazon.com/dp/B07K7QMQ7T/ref=cm_sw_r_cp_apa_i_27P6Cb11GTZ1M

u/fabricwench · 2 pointsr/sewing

Yes, you can use a foot from a different brand. I'm pretty sure your machine uses snap-on feet. When I sew doll clothes, I really like using a clear quarter-inch foot, it's used for quilting but the smaller width and shorter length along with the markings on it are helpful for any small seams.

u/sewistem · 2 pointsr/sewing

I just had the same problem and unfortunately bought the wrong foot. Hopefully I can keep you from making the same mistake. If your machine does one step buttonholes, you need a foot with a slot in the back to place the button. This lets the machine know how big to make the buttonhole.

If you have a machine that does 4-step buttonholes you can use the cheaper feet like this one:
http://smile.amazon.com/gp/product/B008MNWMJY?keywords=Buttonhole%20foot&qid=1453646312&ref_=sr_1_3&sr=8-3

This is the new one I ordered for my machine that does one step buttonholes. It has not arrived yet but I'm hopeful it will work!
http://smile.amazon.com/gp/product/B00MNJIDDM?keywords=Buttonhole%20foot&psc=1&qid=1453646312&ref_=sr_1_18&sr=8-18-spons

u/High_Plains_Grifter · 2 pointsr/myog

Totally! I’ll never go back to clutch motors, I loathe them.

https://www.amazon.com/INDUSTRIAL-SEWING-MACHINE-SERVO-MOTOR/dp/B001VK9YH8

u/BitterBeard · 2 pointsr/sewing

That sewing machine is yelling for oil!
If you want to try it on your own, get something like this that you can put some oil past the bobbin case on the shaft.

Put a towel under the machine and oil every moving part, including under the needle plate after you remove it. Work the oil in hand cranking the machine, see if you can get the squealing to stop.

If you can't get it to stop making noise, probably need a sewing shop to re-grease the internal gears.

Good Luck!

u/0ldGregg · 2 pointsr/sewing

I got a kit on amazon that came with several feet (I bought it solely for the zipper foot I had lost, because it was cheaper than buying a zipper foot alone). It also came with an extension type piece that adds the piece to your machine where snap ons would attach, if your amchien doesnt have it. Some of the older machines dont have this piece, so it allows even those machines to use the universal feet. Janomes are typically not considered universal, though, from what i read but then again they all arent the same. Look at your machine and the attachable snap on adaptation piece...if itd fit, the feet will fit. If you already have the snap on piece built into your machine, just make sure its not too narrow and theyll fit. My kit was ~8$ with shipping and was labeled 11 piece kit, I believe. Edit: Here is what I bought.

u/bombayern · 2 pointsr/Bladesmith

Maybe try getting some 1/4 chicago screws from amazon, they look like they may exactly what you need: http://www.amazon.com/Chicago-Screws-Plain-Pcs-Silver/dp/B00355AN4U/ref=sr_1_1?ie=UTF8&qid=1451505606&sr=8-1&keywords=1%2F4+inch+chicago+screws

In Addition, you could try peening some stainless stock, I do it all the time and they work well

u/RayZfoxx · 1 pointr/LifeProTips

Sewing machine oil is a great light oil that gets down inside the chain like WD-40 but does not contain solvents and its cheap.

http://www.amazon.com/4-oz-Sewing-Machine-Oil/dp/B000H8Q41Y

u/Infinity_z · 1 pointr/3Dprinting

So stuff like this? Also, how do you apply grease/lubricant to the bearings? The rails/worm gear I’m assuming it’s directly applied, then the axis is moved up/down/left/right to apply throughout.


Zoom-SPOUT Sewing Machine Oil Oiler ~ 4FL. OZ.(118ml)
https://www.amazon.com/dp/B00BYCKTW2/ref=cm_sw_r_cp_api_6cPJBb3ZHQ8QH

3-IN-ONE Multi-Purpose Oil, 3 OZ
https://www.amazon.com/dp/B0002JN5PG/ref=cm_sw_r_cp_api_HcPJBbYNBTFVR

Super Lube 51010 Oil Super Lube
https://www.amazon.com/dp/B000BXOGHY/ref=cm_sw_r_cp_api_DdPJBbVT5E89G

Super Lube 21010 Synthetic Grease (NLGI 2), Blistered, ½ oz Tube
https://www.amazon.com/dp/B000BXKZQU/ref=cm_sw_r_cp_api_-dPJBbN0D6KVT

u/hickdawg · 1 pointr/quilting

I use one of these. It is a 1/4" foot with a guide so you have a little extra insurance to help you with your fabric. My hands shake and I also have arthritis, so all the help I can get, I will get! LOL

The foot is cheap and you can always replace it. I should fit most machines if you have something with a low shank snap on.

u/floormonkey · 1 pointr/myog

I highly recommend installing a servo motor. https://www.amazon.com/INDUSTRIAL-SEWING-MACHINE-SERVO-MOTOR/dp/B001VK9YH8

You can dial down the speed and make it easier to use. Careful adjustment of the pedal on the industrial machines are one of the advantages. You can change the pedal action based on what the machine is used for. For example, my binder is set up as mostly an on/off, because all the positioning is done before I start and I run long lines. My 20U and straight stitch is set up for fine work with long engagement.

Of course, the servo motor fixes all that-just change the speed. No vibration, no power use when not sewing, and it's quiet.

u/pto892 · 1 pointr/myog

I put servo motors on both my industrial machines, the work takes only an hour and is well worth it. One can dial in a very precise speed on the motor and then lock it down-so if you want to sew at say 300 spm you can do it. The other thing (and it's a big one in my opinion) is that the servo motors are much quieter than a clutch motor. Clutch motors are noisy as hell, and I already have a significant hearing loss.

/edit-used these if you're interested. They work fine.

u/Le_Squish · 1 pointr/sewing

Is your machine low shank or high shank?
I got mine on amazon as a set for my low-shank Kenmore. It comes with a buttonholer. It has an adapter so it should fit your singer as well.

u/FluffyFoxSprinkles · 1 pointr/quilting

I started with a foot like that and HATED it. I believe what it does is hops. It will come down and touch the foot plate, then raise up and down as you sew. What you need is something adjustable. I would recommend trying something like one of these. You can then make it adjustable with this video from Leah Day

I tried to find a fully adjustable one, for your machine, but I didn't see that Singer made one for a low shank machine, which I believe is what you have. The one I use is from Janome, which should fit your machine, but I couldn't guarantee it, and $50 is a lot to spend for "maybe". Here is the one I use Janome Foot

Edit: Reddit keeps spazzing on me, and erasing my comment. Here's the rest...

So, the difference is... if you look at the cheap foot I linked, you can see that it is spring loaded, which means the foot will be pushed down, until it touches the plate. The motion of the machine will hit the little bar sticking out, and make it move up and down as you quilt. The video I linked from Leah Day, will show you how to make it adjustable by bending the bar back and using a rubber band, so that it will stay in a fixed position. If you look at the $50 Janome foot I linked, you will see that it has an adjustable screw on top, which allows you to raise and lower the foot until it is at the correct height.

I wish I had a better option for you, but with these entry level sewing machines, there doesn't seem to be a lot of options.

With all of that said, I'm not a professional and take anything I say with that in mind. I'm just trying to relay to you, what I learned when I first started with my little entry level machine last year.

Here is a final tip, if you do end up using either of the above options, always keep your foot down as low as possible, with just enough clearance for the fabric/quilt to pass underneath. If you don't, it will lead to all kinds of issues with missed stitches, and not sewing right. You can guess how I learned that. :D

Maybe someone else will have a better answer for you, but that's my two cents. Good luck!!

As a final edit.. I FMQ with the feed dogs up all the time. I find it doesn't really make much of a difference. Also, I just have a little Janome 2212.

u/DelphiIsPluggedIn · 1 pointr/sewing

It's not a tutorial, it's a special foot designed for sewing-in-the-ditch, which you aren't doing. The foot just really helps with the understitching part. This is what I mean

u/ninjabrer · 1 pointr/sewing

What is the subs opinion of the large sets of feet - like these?

My machine has an overlocking feature that I wanted to try out on some stretchy fabric to see if I can get by without a serger.