Top products from r/ElegooMars

Just be careful to make note of the amount as well. The standard is around about $45/L, which would be around 60cad. I'm in the US, so can't speak about anywhere local and such. I just went off of the prices listed on amazon and such.

For the Bluecast:
https://www.digitmakers.ca/collections/vendors?q=Blue%20Cast-3D%20Garage
Note that those are 500g, so approx. .455l, so about 350cad per liter.

Monocure:
https://www.amazon.ca/Monoprice-Rapid-Printer-Compatible-Printers/dp/B07H45B4QF/ref=sr_1_11?keywords=monocure%2B3d%2Bprinter%2Bresin&qid=1575075417&sr=8-11&th=1
That's for half a liter, but priced like a full liter.

Anycubic, they don't have grey atm, but price would be pretty much the same:
https://www.amazon.ca/ANYCUBIC-Printer-Photon-Printing-1000ml/dp/B07GPDMVKP/ref=sr_1_9?keywords=anycubic%2B3d%2Bprinter%2Bresin&qid=1575075556&sr=8-9&th=1
That's for a full liter, and it's cheaper than the half liter of Monocure.

Elegoo:
https://www.amazon.ca/ELEGOO-ABS-Like-UV-Curing-Standard-Photopolymer/dp/B07P6W5L8P/ref=sr_1_6?keywords=elegoo%2B3d%2Bprinter%2Bresin&qid=1575075900&sr=8-6&th=1
A bit more, but not nearly as much as monocure or bluecast.

You could try something like this in a closed Chamber.

build one for my FDM printer with a 220V version of this and it reaches 60°C easily. could definetly go higher i think.

A cheap temperature controller and you're good to go.

You could also just heat up the inside of your building chamber with a small version of this. This ensures a good cooling of any printer components.

OK. The tank I bought for $89 bucks and I put some Mean Green cleaner to run in it. https://www.amazon.com/gp/product/B075FTFD3R

As for the Curing box, I have a lasercutter so, I used the awesome https://www.festi.info/boxes.py/ website and designed a two part slide box. I made some mods in Inkscape to accommodate my light.

I lined the box with this lasercut plastic mirror: https://www.amazon.com/gp/product/B075M7VGVM

I etched this on the outside (you have to remove the top to see it) https://images.app.goo.gl/EJGCvurAFwsE2zwN7

I bought this light: https://www.amazon.com/gp/product/B076P8SMF1

I added this solar turntable: https://www.amazon.com/gp/product/B078N3DR75

Yeah. I plan on setting mine up in the basement because of the potential mess/odor but don't want to plug/unplug the flash drive. My FDM has Octoprint which is a drag/drop of my gcode file. Would be nice to have that on my Elegoo. Fortunately I have network connectivity in the basement, so...

Couple of ways I came up with -

1. I could buy a wifi-enabled flash drive. But that's a single point of failure. Nah.
   
2. I could use some old equipment I have lying around not doing anything - i.e. an old ASUS eeePC netbook. It runs Windows 7 32-bit and just for spits and giggles I installed Chitubox on it and it runs fine (don't think I'll use it on the netbook, though I could attach a spare external monitor and use it as a station next to the printer I guess).
   
   Then I just add this: https://www.amazon.com/Sabrent-Computers-Peripherals-Indicators-USB-SW20/dp/B074TZKGVR/ref=sr_1_8?keywords=usb+share+switch&qid=1566479458&s=gateway&sr=8-8
   
   ​
   
   I can create a share on the network and drag/drop the files from my main PC upstairs, then when going downstairs and prepping the printer with resin, switch the flash connection over to the Elegoo. When done, switch it back. The netbook can sleep when not in use and WOL with a magic packet.
   
   I think anything intelligent on the "B" side of the switch might do - maybe even a Pi Zero W with Samba (can even use WinSCP on the main PC side to copy files over).
   
   Too bad can't control the printer remotely (other than maybe an intelligent power switch to shut it down). Maybe they'll update the firmware to do it someday...
   
   ​
   
   Oh yeah - I have an ELP mini IP camera that will watch the printer so I don't have to stand in front of it...

I built my curing chamber around one of these.

https://smile.amazon.com/gp/product/B077X4V18H/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

I took a 5 gal bucket (Lowes) and dremmeled a rectangular hole in the bottom (to mount the light) and lined the bucket with foil tape like you'd use for heating/cooling air ducts. Works like a champ.

Canadian here, there is a pretty good deal on the 1000g grey right now

https://www.amazon.ca/dp/B07P6W5L8P/?coliid=IC39IYRZ4IBM3&colid=3V9PV3KM90NUC&psc=1&ref_=lv_ov_lig_dp_it

I use this nail UV light from Amazon.

I give the resin 2 or 3 minutes under the lights and that's enough to fully cure it.

To rotate the models under the light, I use this solar powered display

If the model and rotating display are too tall to fit under the light, I support the light on some plastic boxes. Try not to look at the light and keep pets away.

Here’s the one I bought. The silicon goes into the bottle, and the metal filter sits inside that. To clean it up, I just rinse it in some alcohol to clear out the particles.

Aibecy 3D Printer Accessories Parts Collapsible Funnel Silicone Foldable Funnels Stainless Steel Resin Filter for Pouring Resin Back Into Bottle for ANYCUBIC Photon Sparkmaker Kelant Orbeat D100 https://www.amazon.com/dp/B07SGC1LND/ref=cm_sw_r_cp_api_i_Efz2DbVSBRQ8P

I printed the plugs with cavities for the logos, then mixed some of the white with different alcohol dyes (128 drops per 30ml of white gave some nice colors) and used really fine tips to fill them in and put it under the curing lamp. After they were cured for about 15 minutes, I wet sanded them smooth, from 500 grit to 1000 to 3000.

Bottle set: 30Milliliter Precision Applicator... https://www.amazon.com/dp/B07CMQSWKJ?ref=ppx_pop_mob_ap_share

Alcohol Dyes: 12 Colors Epoxy UV Resin Color... https://www.amazon.com/dp/B07NQ4Y85H?ref=ppx_pop_mob_ap_share

I think one of these should work. The thingiverse mentiones 45cm long, which is roughly 17 inches, so I think a 16inch or 19inch should be fine without cutting.

https://www.amazon.com/Hardened-Chrome-Linear-Motion-Shafts/dp/B01LXAZFKZ/ref=sr_1_3?keywords=8mm+rod&qid=1566315274&s=gateway&sr=8-3

https://www.amazon.com/ReliaBot-Hardened-Chrome-Plated-Linear/dp/B07DPFH7HL/ref=sr_1_5?keywords=8mm+rod&qid=1566315497&s=gateway&sr=8-5

I bought these and they have been working just as well as the included fep, correct size and everything.

https://www.amazon.com/gp/product/B07X455HVT/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

Are these the trays you are referring to? They look extremely useful... except that I haven't once seen them in stock...

ELEGOO 4 PCS Plastic Resin Tank for ELEGOO Mars 3D Printer with 4 Lids and FEP Release Liner pre-Installed, Resin Vat for Mars, Compatible with Anycubic Photon, Photon S and Epax X1 https://www.amazon.com/dp/B07X455HVT/

https://www.amazon.com/ELEGOO-Plastic-pre-Installed-Compatible-Anycubic/dp/B07X455HVT

I did notice Elegoo has them in stock though https://www.elegoo.com/product/elegoo-4-pcs-plastic-resin-tank/