Top products from r/Louqe

We found 25 product mentions on r/Louqe. We ranked the 25 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Top comments that mention products on r/Louqe:

u/17jwong · 1 pointr/Louqe

The bubbles form naturally during the bonding process; it states this on the back of the container. Here is a link to the Amazon page where I purchased the acrylic cement.

> The product you bought might call it weld, but it really, its not.

This is the same product and technique people use to build acrylic aquariums. If it's good enough for them, it's good enough for me.

> Why do you think all mods/pro today use rubber gasket.

Here's an acrylic reservoir made by Swiftech that is joined with cement and not gaskets.

Edit: just responding to your ninja-edit, I use Weld-On 3 because I feel the faster bonding time makes the pieces easier to work with, plus it's one of the most commonly recommended acrylic adhesives along with Weld-On 4.

u/J7mbo · 1 pointr/Louqe

Yep I rotated 180. For the clips, I just removed them completely. The fan just sits there, it doesn't move or anything so it's nothing to worry about.

I'm using Corsair Vengeance LPX DDR4 RAM, I got 1x 16GB stick and will upgrade to 32GB some time later.

To be clear: it is a VERY tight fit, but totally worth it once you've gotten it shoved in properly.

u/Ethan_NLHW · 5 pointsr/Louqe

I replaced the ones on mine with these. They stick great and actually add some clearance for slightly better airflow.

https://www.amazon.com/dp/B075KM5Y8W/ref=cm_sw_r_sms_apa_i_g4NTDbC2RKG6D

u/shmoley999 · 1 pointr/Louqe

I got them from this but something like these should work well

u/drkmrk · 2 pointsr/Louqe

Any 1" Silicone with Adhesive Hemisphere feet will be a great replacement.

https://www.amazon.com/dp/B075KKRJXH/ref=cm_sw_r_other_apa_i_nyxYDb50RAJZA

u/Zer014PH · 1 pointr/Louqe

I only need 1 m.2 slot, will use one full 2.5 ssd for secondary drive. i know cutting 4mm on the phantom works to fit the L12S but i dont feel like butchering the board lol, found this heatsinks for the vrm, chipset and m.2, will buy thermal tape to stick those. will this be enough to replace the phantom's stock heatsink if i dont plan to OC the system?

VRM/ chilset heatsink
https://www.amazon.com/Heatsink-Cooling-Stepper-Regulators-Raspberry/dp/B07V9XDJNF

M.2 heatsink https://www.amazon.com/Pack-Heatsinks-Cooler-Silicone-Thermal/dp/B07DNC4YP8

u/Whoa_There_Hoss · 6 pointsr/Louqe

Edit: Adding PCPartPicker link and a few more details...

PCPartPicker: https://pcpartpicker.com/b/4tZRsY

More pictures: https://imgur.com/a/UNqsFuO

Specs of "Lil Chungus" below:

  • Case: Louqe Ghost S1 (Limestone) + Large Tophat
  • Mobo: Gigabyte X570 I Aorus Pro WiFi Mini-ITX
  • CPU: AMD Ryzen 7 3800X (w/ Thermal Grizzly Kryonaut)
  • GPU: NVIDIA GeForce RTX 2080 Super FE
  • RAM: Corsair Vengeance RGB Pro 32GB (2x16GB) DDR4 3200
  • PSU: Corsair SF750 PSU
  • Cooling: Corsair H100i RGB Platinum AIO Liquid CPU Cooler
  • Boot Drive: Sabrent 1TB Rocket NVMe 4.0
  • Extra Drive: Samsung 860 QVO 4TB SSD
  • Lighting: Cheap RGB strips to light up the GPU
  • Keyboard: Steelseries Apex 7 TKL w/ HyperX B&W Pudding Caps
  • Mouse: Corsair M65 Pro RGB FPS
  • Monitor: Acer Predator Z35P
  • Desk: These legs attached to the top of this desk. I don't recommend the legs as they don't go low enough.
  • Chair: Secret Labs - Titan
  • Tablet: HP Stream 7 (pls do not buy this ancient turd)

    Camera used here: Sony a6000 w/ Sony SEL50F18 50mm/1.8 for most shots. Switched to a Rokinon 12mm F2.0 for the wide shots. The post's main picture was at f/11, 1.3sec, ISO-100 on that 50mm lens.
u/agonzal7 · 2 pointsr/Louqe

Hmm I’ve shared the link before. They’re from amazon. Just some rubber sub woofer feet. I use double sided tape to get them to stick. Hudson Hi-Fi Silicone Isolation... https://www.amazon.com/dp/B075KPHZPF?ref=ppx_pop_mob_ap_share

u/HelloBloom · 2 pointsr/Louqe

£200!?

The first result on Amazon is £75
www.amazon.co.uk/dp/B07D99S8Z7/

Or get the 4Tb ones I did off eBay for £80.

u/liv2powski · 1 pointr/Louqe

Found this guy on amazon. Stupid question, any idea if other hardware is needed to connect the grill to the fan?

OKGEAR 120mm Fan Grill/Guard - Black https://www.amazon.com/dp/B005VRK5YS/ref=cm_sw_r_cp_api_i_1kLUDb646V4CH

u/DumbledorePool · 1 pointr/Louqe

so this one should be fine?

https://www.amazon.com/gp/product/B07F84FJ1G?pf_rd_p=183f5289-9dc0-416f-942e-e8f213ef368b&pf_rd_r=MQD2HE0K7M5B400ZNTAK&th=1

Edit: they have two styles listed, sf and sf platinum. in the picture the sf platinum appears bigger, not sure if that to show the size or if it doesn't have an meaning. Guessing SF Platinum 600 would be okay for my Ghost S1 build?

u/OG_PANDA_KING · 1 pointr/Louqe

https://www.amazon.ca/Innovation-Cooling-Graphite-Thermal-Pad/dp/B07CK9SHZG

Read up on the proper application method for the paste. I believe you need to spread a thin layer throughout.

u/kebbn · 1 pointr/Louqe

Pangea just came back in stock, shipping Sept 18th. It appears randomly for maybe half an hour before disappearing again. I ended up choosing this last week when it went in stock for a brief moment, and they actually ended up shipping it yesterday (?!).

Was sick of waiting for Limestone - come join the green side guys ;)
https://www.amazon.com/dp/B07GNMFTHZ/ref=cm_sw_r_cp_apa_i_tv-EDbXA9THD3