Top products from r/folgertech

We found 10 product mentions on r/folgertech. We ranked the 10 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Top comments that mention products on r/folgertech:

u/lxlqlxl · 1 pointr/folgertech

Wow.. this is easily the longest reply I have ever gotten. I have replied much longer before but yeah.. Not complaining at all thanks for taking the time to write it. I will reply as I read through.

Wiring for me I have never been all that hesitant to. I have been hit with 120 a few times and it's mainly a burn for me. The one that really surprised me though was taking apart a blender and well I had shorts on and you can touch one wire and be fine just not both unless you and the wiring are grounded of course. Anyway I was on my bed and one wire was touching my leg and the other I grabbed with my hand... So that was an interesting experience.

I am the type that will take one of those cigarette lighters that electric spark? take off the guard, put your thumb over it and go... clicky clicky...

As for the JST bit I appreciate the links. I am familiar with them and how to do that I just never have. I would need a reason to get them, maybe this is it? But the wago or other lever type connectors seem to be easier and or cheaper. I will figure it out when it gets here.

> personally I mangled the connector housings and pins on my stepper cables trying to swap pins over.

Yeah I think you need the pin remover. I was watching a few youtube videos about it, and well here I believe is the one I watched. Relevant portion is at the 7:05 mark https://www.youtube.com/watch?v=RhU0D7fDR98 It's called an extraction tool, or extractor. There are quite a few different ones for different applications. If I got into solderless pin connections that's one of the things I would buy.

So for me going that kind of connector route would be about 10 or so for the extractor, 20 for the crimper, maybe 10 or so for the connectors. But let's say it was just 30 or so total. Ok... or I could go with the wago lever connectors for 15 and could splice 50 sets of wires that could be undone with a flick of a lever. It's not as nice looking as a connector but it's still doable. Also knowing me, I'd still throw some heat shrink tubing onto the crimped pins. But I already have that and a heat gun.

>Building a cat proof mdf enclosure for the printer so I can take it home within the next month or so is on the cards.

I plan on copying the corner bracing and modifying those. Well I want to replace all the melamine parts eventually but yeah. The idea would be to modify those in a way I could easily attach side and top panels. Likely something like 1/4" plexi glass. I don't like how the socket caps stick out, so I would use countersunk screws to make the screw head flush with the printed brace. Then either on the back side hollow out a section for a neodymium magnet for each corner and do the same for the plexiglass, or maybe thumbscrews? Or possibly just make it so it's like the side of a PC case where it slides in and out The top would likely be semi permanent and attached with screws but the sides would be like just slide the panel up and take it off that way. The front maybe the same way or use hinges or whatever. I don't think I will print any ABS I hear enclosures could help with that. My main reason for doing it is dust. Dust I hear can mess up prints so keeping it enclosed may help with the quality.

For me an MDF enclosure would be really easy to do, I may do that as a frame then attach plexi to the outside and just have a box that goes over it? but that to me seems like cheating and or wasted space... also no challenge. I like challenging myself so unless I absolutely need it and I can't figure out the other bit then maybe? But what I have in mind should be relatively easy to do.

About the router stand... Looks good, but I must admit when I read "router", I thought of like an actual router well the woodworking kind.

The CTC-3D clone? or? I haven't looked into those so I am not very familiar. I am mainly interested in kits not fully working right out of the box... and you answered that later in the post... nice.

The fan bit. I plan on tinkering around a lot with that well the shroud bit. I have thought of an experiment to try to test out which ones are better, and I will throw in different speeds, different nozzles as well and document the process. I will take a few that others have designed, and design some of my own to see how they differ in performance. The test will be of multiple prints of a similar object, essentially 2 poles at varying distances, like half an inch up to say 3 to 5 inches or however long to see how far each can bridge the gap with little to no sagging. Then maybe ledges at varying lengths.

As for the V6 clone bit. I already bought one of these J-Head V6 Bowden and an MK8 Bowden feeder. I primarily got those to see if I like the bowden setup over the direct. If I find out I like the direct I will probably get this. If I like the bowden bit I think I could still get that one and just change out the heat sink and use the other bits. Either or fun times ahead.

>Or even the new e3d aero if you don't want v6 style eating into your build height.

If I need more build height, I can just get some longer rods, and some longer 2020's and extend it out. My main thing is I wanted 12"^2, since this is like 15.75" unless it takes 3.75" more of build height away I don't think I will fret too much.

>Definitely use the stock for a few months

A few months is an eternity for me. Maybe it will take that long to get built and dialed in? Who knows... Either or... the plan is to get the printer from kit form built and working and at least functional with prints. The only "change" will likely be with a 12x12 glass or mirror bed. Once it's up and running and I have a base to work from that I know works. Then I will change it over to bowden with the ones I linked and try that out for a while. Then decide whether I want to get the e3d one or not. The only reason I'd get the e3d one is the socks which I could buy seperate and the hotend tube. If I could find that bit seperate I probably wouldn't buy the complete kit. I know I can buy the "clone" version but the teflon tube is used as a liner and I'd like it to potentially be able to get up to around 300c without worrying about that liner melting. I also plan on getting some stainless nozzles and maybe... just maybe one of the tungsten ones. Not necessarily to use with this printer but likely the one that I design and build after this one. Think multiple independent extruders(not sharing the same block), and large... er build volume. I won't get too much into that idea right now though.

>I'd say the z axis rods are the one part of this built machine that is a little more difficult to access/disassemble easily

Yeah I'd say that looks fair. But that's also one of the selling points for me. That design looks rock solid. Even with the shitty melamine. I think once you get the binding figured out on the Z and have an idea how to do it regularly it will become less and less of a pain. As for the threaded and smooth rods, and only the threaded need to be somewhat loose? I heard it was pretty much all of them until it was aligned properly. Try loosening all of them up a little bit. Running it to the top and bottom then go to the top, tighten things down then down to the bottom then tighten. That should resolve any binding. From my understanding at least. It doesn't seem like you have tried that approach yet.

>TBH the melamine parts aren't that terrible.

Well for me I am not hugely against it but yeah. They work just not for my liking. I was initially hoping they would be actual solid melamine. But it looks like it is actually a melamine coating on top of low quality mdf. If it was actual melamine it would be a lot harder and wouldn't crush that easily. Actual melamine is a lot closer to a plastic than what that appears to be. Here in the states at least melamine is commonly put over particle board for counter tops. It's good so long as you don't get water on the edges as it will eventually swell.

As for the bracing... I assume you have home improvement stores there? If so try to find some of these if you don't want to print out new ones. Just figure out the dimensions you want with those flat corner braces and use those. You may need slightly smaller M5's but those are pretty cheap as well. Or if you have a grinder... you could knock a few MM off the ones you have.

>standard board will do the job just fine. The lure of touch/colour screens for 32 bit SBase boards isn't really for me.

I don't think I will go the touch screen route designed for these, If I go that route I will likely add wifi capability, and add a small tablet with browser functionality ;)... The reason for me, for 32 bit is 1/128 stepping, as well as quieter motors, and can be more complex without the program stuttering due to not being able to keep up with the needed calculations. With that I plan on trying to see the maximum print speed I can get and still get decent quality. Just to give you an idea. I plan on bolting it down to a heavy surface due to the inertia of the motors going side to side to keep it rock solid, that may give you an idea on how fast I am planning on cranking this or the next one up to, and yes I know I will likely need better motors and or stronger drivers and crank up the current. Maybe even a stouter belt system? Enclosed chain perhaps? Or longitudinal setup like this? http://www.technicopedia.com/8094/8094-2longitudinal.jpg, well without the extra bits.

As for the USB bit I am going to tinker around with that and SD card, I have a spare laptop I don't really use I can use for that purpose.

u/danimal300 · 1 pointr/folgertech

These are the motor mounts and pulleys I used. Cheap, sturdy and easy. In the video above you can see how well the line up. The aluminum pulleys are okay, not great, but they seem to be wearing well and have not had any problems. There are better ones out there, but these are the ones from my amazon shopping cart and should be a good starting point.

https://www.amazon.com/gp/product/B01HHPD7LY/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

https://www.amazon.com/CTYRZCH-Aluminum-Pulley-Bearings-Printer/dp/B06XHY2RWZ/ref=sr_1_31?s=industrial&ie=UTF8&qid=1494562287&sr=1-31&keywords=gt2+pulley

https://www.amazon.com/BIQU-Smooth-Precise-Bearing-Printer/dp/B01FTZMXDW/ref=sr_1_27?s=industrial&ie=UTF8&qid=1494562287&sr=1-27&keywords=gt2+pulley

u/sonnylowe · 1 pointr/folgertech

I just bought this on Amazon Pin Header Kit looks like a nice kit, I get it tomorrow, if you give me day and can confirm the quality for you...


Edit: You'll need a crimping tool as well...you can as nice as you want, but THIS should work fine.

u/TheOddArtisan · 1 pointr/folgertech

It is the case that came with my Pi when I purchased a Canakit bundle. Here is the case by itself.

With a couple short bolts and t-nuts, I used the mounting holes already designed in the case to secure it to the 2020 frame!