(Part 2) Top products from r/zwave
We found 4 product mentions on r/zwave. We ranked the 24 resulting products by number of redditors who mentioned them. Here are the products ranked 21-40. You can also go back to the previous section.
21. GoControl WD500Z-1 Z-Wave 500-Watt Wall-Mount Dimmer Switch
Sentiment score: 1
Number of reviews: 1
Wireless Z-wave Wall Dimmer SwitchZ-wave & Manual Control For Connected Lights500w (4a) Max LoadFits In Standard J-boxWhite.This device requires a neutral connectionUses Z-Wave's Scene Command ClassEasily replace existing standard switch to add a Z-Wave controlled lighting dimmer. Compatible with an...
22. GE 45631 Z-Wave Wireless Keypad Controller
Sentiment score: 1
Number of reviews: 1
Allows you to remotely turn the light or appliance on/offFunctions as a secondary controller in the Z-Wave networkSoft-touch, translucent buttons with soft LED glow for command confirmationControls four groups and four scenesBattery-powered – no wiring neededLow profile, white light controlRefer t...
23. Monoprice USB Extender over CAT5E or CAT6 Connection up to 150ft
Sentiment score: 0
Number of reviews: 1
USB specifications limit the maximum run for USB to only 15ftThis can make placement of USB devices difficult especially in a wide areaThis can be especially convenient if you already have unused Ethernet cabling pre-installed in your walls
24. GE Z-Wave Wireless Smart Lighting Control Light Switch, On/Off Paddle, In-Wall, White & Lt. Almond Paddles, Repeater & Range Extender, Zwave Hub Required- Works with SmartThings Wink and Alexa, 12722
Sentiment score: 1
Number of reviews: 1
"ALEXA COMPATIBLE - REQUIRES AN ALEXA SUPPORTED HUB for voice control with Echo Products (Alexa device and hub sold separately). CANNOT connect directly with ECHO PLUS (Only ZigBee products can connect directly to Echo Plus).Requires a Z-Wave certified gateway. Compatible with the following Z-Wave c...
Your worst case scenario is to put 2 remote zwave switches up in the ceiling fan. This will require bypassing the remote module in the fan, and wiring the lights driectly to one of these zwave switches. Secondly, You would remove the wall switch as it won't help this setup (wire it straight through and put a cover on the box.) And finally, you would still have to use the original remote to control fan speed. Maybe put a zwave scene controller panel over the unused wall switch box.
If you open the wall switch box and you find that 14-3 wire was run between the switch and fan, then your options just got alot better. You could expand the box to be 2 gangs, Put in a zwave switch for the lights, zwave fan controller, and send the power down that the black wire, and the other the red. You'll still have to bypass the fan's remote control module, but now for the fan and the lights as the zwave in wall fan controller will handle the speed.
Do you have a dimmer instead of a switch? The difference is important.
I use this for my florescent lights. It clicks when you turn on or off the light. https://www.amazon.com/gp/product/B0035YUOWC/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
I use this for other dimmable lights. The light (and assume the power to the bulb) ramps up to full power.
https://www.amazon.com/gp/product/B00E1OVFAK/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
Have you tried replacing the bulb? Is your garage cold? Cold effects these bulbs pretty drastically. When it's cold (<30°) mine only operate at about half the brightness for a few minutes.
It's definitely a switch and not a dimmer (specifically this one https://www.amazon.com/dp/B0035YRCR2/ref=cm_sw_r_cp_apa_JjFwybQJGCRY8), leaving the light in didn't help, and the light works (comes on instantly) since I put the original switch back in place.
Monoprice USB Extender over CAT5E or CAT6 Connection up to 150ft https://www.amazon.com/dp/B003L14ZTC/ref=cm_sw_r_cp_api_i_ZxwcBb3X14395
Why do you restart HA so frequently?