Reddit reviews 2-Channel Speaker to RCA Converter - 2 Channel Hi/Low Level RCA Converter w/ Ground Loop Isolation and Noise Elimination, Aluminum Housing, Adjustable level, 50W Max Input - Pyle PLVHL60
We found 6 Reddit comments about 2-Channel Speaker to RCA Converter - 2 Channel Hi/Low Level RCA Converter w/ Ground Loop Isolation and Noise Elimination, Aluminum Housing, Adjustable level, 50W Max Input - Pyle PLVHL60. Here are the top ones, ranked by their Reddit score.
HIGH-LEVEL RCA OUTPUT: The 2 channel speaker to RCA converter takes a low-level input and converts it to a high-level input and converts it to a high-level RCA outputLEVEL ADJUSTABLE: Pyle link line out converter has a built-in level button control and smooths out your signal for output to an amplifier. It is designed to connect or integrate your 2 channel head unit directly to your sound systemHIGH-QUALITY SOUND: No need to worry about interrupted sound, static or loss of quality during an important event because this cable is made with highly durable construction and delivers premium performance without noise, static, or buzzingMINIMAL SIGNAL LOSS: Features round loop isolation and noise elimination and made with precision formulated materials for maximum signal transfer and ensures optimal signal stereo audio transmission. Perfect for on stage or in a studio useMADE TO LAST: The Pyle audio connector is equipped with an exclusive aluminum housing for long lasting protection even after repeated use and it fits perfectly to any device and doesn't get easily disconnected by light tugging or dragging2 Channel Hi/Low Level RCA Converter - 2 x Female RCA OutputsLevel Adjustable - Dimensions: 3.6''L x 2.6''W x 1.08''HGround Loop Isolation and Noise EliminationAluminum HousingMax Input: 50W
If it has a tape out, then you can definitely use it as a preamp, but you won't like it because you won't have volume and tone controls since the purpose of the tape output is to bypass those controls.
You have two ways around this. First, you could go into the amplifier and tap the signal where it goes to the power amplifier, then just remove the output stage tubes. There are some dangerous voltages involved there, so unless you know what you're doing you might not want to try this.
A second one very easy way is to use a speaker to RCA level converter like this. You just connect this instead of speakers. It works for amplifiers up to 50 watts.
Hope this helps.
You can usually pretty easily run a power wire to the trunk using holes that already exist, and you can get adapters the go from speaker level to RCA, so you just tap into the rear speakers. Something like this http://www.amazon.ca/gp/aw/d/B000ES9QNA
Headphone out to RCA will work fine, just get the right cable, 1/4" TRS to Dual RCA, 2 Meters.
The other option is a Speaker to RCA Converter.
Or some low budget speaker options: Dayton Audio B652 $30, Polk Audio R150 $45, Dayton B652-AIR with AMT Tweeter $50 or look for some better used bookshelf speakers for $50 or less.
Probably a stupid thought, but have you tried using the other set of speaker outputs on the back of the amp? Also, have you tried new speaker wires? If you run them out of spec, you can literally melt them (or a cat might have chewed on them).
You could also try something like this connected to AUX-out in case the speaker-outs on your amp are shot.
Ahh yes. BUT!!! there is a way around that...
You splice your speaker wire into this guy. Might take a little electrical tape to cover it, but it does the job. I did this for an amp for my GFs son. I got him some thrift store Sony bookshelves and a NobSound BT mini amp. I had an extra sub laying around, but no line level inputs. I spiced this unit in and it works just as though it had line inputs.
https://www.amazon.com/PYLE-PLVHL60-Channel-Speaker-Converter/dp/B000ES9QNA/ref=pd_sbs_107_5?_encoding=UTF8&pd_rd_i=B000ES9QNA&pd_rd_r=GSWTEQMEDQQVVWYSQCP2&pd_rd_w=Zp49L&pd_rd_wg=QeNBK&psc=1&refRID=GSWTEQMEDQQVVWYSQCP2
>Do you guys have any suggestions on how to pair these with my other speakers and receiver so that volume changes from the receiver don't result in imbalance?
Sure, you could use speaker to line-level converter such as this or this. It's not an elegant solution but it should work fine. Take care when wiring it up as doing so incorrectly could damage the receiver.