Reddit reviews 7440 7443 LED Brake/Tail Light Bulb Pure Red Super Bright High Power Non-Polarity 7441 4014 992 W21W T20 LED Bulb (2 PCS)
We found 1 Reddit comments about 7440 7443 LED Brake/Tail Light Bulb Pure Red Super Bright High Power Non-Polarity 7441 4014 992 W21W T20 LED Bulb (2 PCS). Here are the top ones, ranked by their Reddit score.
Ultra Bright & Energy Saving: (Set of 2, (Set of 2, Brilliant Red)) With the high power 3020smd chipset, these 7443 LED bulbs are only 6.2W/PC but 2 times brighter than the original bulb.Safer and Quicker: 360° shining without dark spots, the 7440 led brake light bulb is instant start, no delay, safe and reliable enough, no glare to other drivers.Double Heat Dissipation: Aircraft grade aluminum body built and unique bump appearance design increase the heat dissipation area. Wide voltage & constant current provide up to 30, 000 hours lifespan.Fitment: Compatible with US standard and CK sockets. Fits for 7443 7440 7441 4014 992 W21W sockets. Similar size to the halogen bulb, easy installation, just plug and play.Important Note：Please double check your vehicles owner’s manual or the original bulb to confirm the correct light size you need before placing the order. Load resistor or flash relay might be needed to prevent the hyper flash or system error.
So it is actually a 3 part ordeal.
The actual fog lights since my car didn't come with them, and the stalk. Then I did some c-shaped drl since I have leds in my high beams and the factory drl doesn't work with leds, but then the c-shaped drl didn't work for a little bit so I bought the drl turn signals, and then the previous c-shaped ones started working again. I will just post all of my mods below:
Fog lamps with brackets : https://www.amazon.com/dp/B01FL8DPWU?ref=ppx_pop_mob_ap_share
Light stalk : https://www.amazon.com/dp/B00AWO7XOK?ref=ppx_pop_mob_ap_share
C-shaped DRL : https://www.amazon.com/dp/B014P7LPEI?ref=ppx_pop_mob_ap_share
Sequential LED Turn signals with DRL : https://s.click.aliexpress.com/e/5veD22k
9005 LED High Beam : https://www.amazon.com/dp/B075J9S4DT?ref=ppx_pop_mob_ap_share
H11 55W HID Low Beam : https://www.amazon.com/dp/B07CMKT2F4?ref=ppx_pop_mob_ap_share
7440 7443 LED Brake/Tail Light : https://www.amazon.com/dp/B07GTKLF32?ref=ppx_pop_mob_ap_share
7440 LED Turn Signal (rear) : https://www.amazon.com/dp/B07Q8RZRZV?ref=ppx_pop_mob_ap_share
194 LED License plate/used as side markers in the front/a couple other places : https://www.amazon.com/dp/B07BT23WVC?ref=ppx_pop_mob_ap_share
194 LED side marker bulbs (not used but the correct ones if you want yellow, I liked the white and it was what I had when the originals burnt out but didn't ever change them from the above link) : https://www.amazon.com/dp/B01KY7GCXW?ref=ppx_pop_mob_ap_share
License plate smoke : https://www.amazon.com/dp/B007LICQ9M?ref=ppx_pop_mob_ap_share
Grille : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F254096211721
K&N 33-2480 Air Filter : https://www.amazon.com/dp/B00CR9WVPE/ref=cm_sw_r_cp_api_i_VfS6CbNBD59AQ
I had my rims done by a local company, they are the factory 16" painted gloss black. My mazda emblem is actually a long story, but essentially it is just scuffed up with sand paper ready to be painted but I liked the look and stuck it back on the way it is. I have also installed car play, and 3D printed a shift knob. The factory bose system was a little lacking and put a small under seat sub in to help fill the sound, but am still not happy with it, so that's a future project.
Some near future plans for the car include the aero kit, and I'll post the links to those here too:
Front Bumper Lip Air Dam : https://www.amazon.com/dp/B01FTUE8EY/ref=cm_sw_r_cp_api_i_bdS6Cb2X8Y22M
Black Mirror caps : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F283050942561
Side skirts : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F391544070112
And the rear diffuser : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F113007041503