Reddit reviews Honeywell HCE100B Heat Bud Ceramic Heater Black Energy Efficient Space Saving Portable Personal Heater With 2 Heat Settings for Home, School, Office
We found 8 Reddit comments about Honeywell HCE100B Heat Bud Ceramic Heater Black Energy Efficient Space Saving Portable Personal Heater With 2 Heat Settings for Home, School, Office. Here are the top ones, ranked by their Reddit score.
Energy Efficient Heat: The Honeywell HeatBud Ceramic Personal Heater Is a 250 Watt Energy Efficient Solution That Provides Just the Right Amount of Heat for You. Specially Designed for Personal Warmth, It’s Perfect for Use at Home, School or OfficeEasy to Use; Designed with ceramic technology that provides fast, even heating, this energy efficient heater uses only 250 watts. It features 2 heat settings, easy one button controls, a tip over switch, cool touch housing & overheat protectionIncrease Your Comfort;Using portable heaters in your home can help increase comfort & supplement home heating needs. There is a range of Honeywell heaters covering personal, ceramic, fan forced, radiant and infrared to meet all your heating needsSMART SAVINGS: Portable heaters are a smart and easy way to add warmth to any space. By turning down your whole house thermostat a few degrees and heating just the room you are in, a Honeywell heater can help you save money while providing soothing warmthHONEYWELL QUALITY: Help improve heating & energy savings in your home, office or at school using a Honeywell portable heater
I've done similar to what /u/Zephyrzuke had mentioned in comments.
My printer enclosure is pretty big (30.5" x 23" x 26.5") to enclose my Taz 6 and I print almost exclusively ABS, some recommended around 50C but I felt like it was a bit excessive after a few prints myself. The bigger your enclosure is the harder it is to maintain higher temperature. On the other hand the bigger your heated bed is the more it contributes to heating the enclosure. I only turn on my heater when doing bigger/taller prints and usually only keep it between ~40-43C/105-110F to minimize the amount of time my heater is on and no warpage on any of my prints; this of course also varies between different ABS filaments.
Used this controller and this cheapo heater. Usually these desktop personal heaters have a tip-over cutoff switch that I've had to bypass and wired directly to the controller.
I didn't like how the appliance-looking heater next to my printer so I designed/printed it a more fitting casing. https://imgur.com/a/xoils
I have that heat controller in my Amazon cart right now. I am going to hook it up to: https://www.amazon.com/Honeywell-HCE100-Ceramic-Portable-Mini-Heater/dp/B00I4UVGHO/
I am going to have this heater in the tent. When I get down to 65 degrees it will go on and shoot hot air under my oscillating fan which will disperse the warm air in the tent. This is a very small heater. More of a personal space warmer.
But I chose it because of it's electricity draw which is 170W or 250W depending on speed. If I use a regular space heater then there is no 3rd tent for me because I run out of electricity. And I really want that third tent.
I use this guy for a heater in my fermentation fridge (larger chamber of a side-by-side). Amazon LINK It's inexpensive and has a built in fan which helps distribute the heat. I sometimes do split batches in 2, 3gal carboys, so it works a little better than rigging up individual heating pads/tape.
There isn't really anybody making a mini thumb trackball as far as I know (and I'd like to know because that or a TrackPoint would be awesome). A lot of people put a regular trackball in the middle, which is a decent compromise. It's possible to make one and integrate it directly with the keyboard, but I haven't really seen it done.
Putting a heater in the case is not a good idea, though. Apart from being complicated and a bit dodgy, hardly any of that heat is gonna conduct into your fingers. There are tons of small electric heater fans you can get that would do the job better, for example this one.
Ergodox is DIY and open source. You can mod it however you want if you're willing to put in the work to do it.
I have one personal desk heater for sale. Nothing wrong with it, only used once as I decided I prefer the electric blanket. $15
I don't see why office dwellers need 1500 watt space heaters unless the heating system in the office is down completely (and even then when I was issued one I used the 750 watt low setting most of the time).
It may be possible to satisfy some users with a fraction of the power. IN FACT They make space heaters specifically for this use, currently there are two models that I have found:
It may be worthwhile considering these heaters in some of these situations.
I have a ~5 cubic foot chest freezer with an Inkbird temp controller. For the heating portion I use a small honeywell heater that also has a fan, similar to this one
How about this:
Honeywell HCE100B Heat Bud Ceramic Heater Black Energy Efficient Space Saving Portable Personal Heater With 2 Heat Settings for Home, School, Office https://www.amazon.com/dp/B00I4UVGHO/ref=cm_sw_r_cp_apa_i_eTxxCb5DENWQ4
The low setting is 125 watts, couple it with a programable thermostat (for heatmats) and you should be good. I grew a plant in a spacebucket in my garage during winter using the same setup, worked out great.