Reddit reviews Stanley 45-300 Aluminum Carpenters Square
We found 1 Reddit comments about Stanley 45-300 Aluminum Carpenters Square. Here are the top ones, ranked by their Reddit score.
Stanley - Black & DeckerHelpful reference conversion including new lumber, decimal equivalent, and metric conversion tables; 45-, 60- and 30-degree angle markingsHigh Quality New!!!!!!!Deep, embossed, 1/8-inch graduations for long-term visibilityBody: 24- by 2-inches; tongue: 16- by 1-1/2-inches; backed by lifetime limited warrantyAluminum carpenter's square offers wide range of easy-to-read measurements, tables, and conversionsHelpful reference conversion including new lumber, decimal equivalent, and metric conversion tables; 45-, 60- and 30-degree angle markingsHigh tempered aluminum for maximum durability; protective lacquered coating; buffed finishDeep, embossed, 1/8-inch graduations for long-term visibilityBody: 24- by 2-inches; tongue: 16- by 1-1/2-inches; backed by lifetime limited warranty
---
Section 1: Tools
---
Note: Just because it is more expensive doesn't mean it is better. You could get by just fine with the "cheaper" options.
---
| Tool | Required vs. Optional | Use | Notes | Price & Link |
|:---|:---:|:---|:---|:---:|:---:|
| Tandy Wholesale Membership | O | Allows you to get better pricing at Tandy. | This is definitely optional. Items will cost slightly more without it OR if you have a tax ID you can get the membership with better pricing for free. | $35 / Free|
| Awl Haft | R | The handle which will hold your blade. | This particular haft allows for different blades to be added or removed with ease. | $16 / $35|
| Diamond Awl Blade| R | This is the blade used for piercing the holes in your projects.| This goes in the awl haft.| $4.80 / $28
| Channel Groover | R | Used to measure and gouge channels where your thread will lay. | Some say gouging a channel is optional however I find it to be required. It further protects your thread from damage. | $16 / $80 |
| Overstitch Wheel | R | Marks where you will punch your holes. | This particular overstitch wheel is a few dollars more than the versions that only offer one wheel. | $24 / $225 |
| Edge Beveler | R | Used to bevel and round off the edges of your project prior to burnishing. | Sizes vary. The smaller the number, the smaller the round edge. | $12 / $55 |
| Adhesive Glue | O | Used to hold your pieces of leather together prior to piercing the holes. | Some people prefer binder clips instead of glue. I've found that the clips end up making marks on my projects so I've always stuck with glue. | $6 / $30 |
| Gum Tragacanth | R | Used as a burnishing agent for your edges.| Some people use saddle soap. I prefer gum trag.| $6.40 / $21|
| Harness Needles | R | Used in combination with the thread for your projects. | Avoid the stitching needles. They break very easily.| $5.99 / $7.50 |
| Xacto Blade | R | Used for cutting projects. | You may have one of these at home already. Be ready to have replacement blades handy ($21.95) | $2.49 / $50 |
| Self-Healing Cutting Mat | R | Used for cutting your leather projects.| You may have one of these at home already. If so, you can obviously use that.| $14.73 / $50.80 |
| Cork-backed Ruler| R | Used for cutting straight lines.| I highly recommend the cork-backed version. It will save from accidental cuts/slips.| $4.80 / $14 |
| Burnishing Tool | R | Used in combination with the gum tragacanth to get a good burnish.| A good piece of canvas can be used as well. | $8.99 / $80 + $99|
| Sanding Tool| O | Used to sand down the edges prior to burnishing.| You might have sandpaper at home. Feel free to use that too.| $7.30 / $0 with dremel|
| Steel Square | O | Used for creating nice, even squares/rectangles for projects. | Learn to use this correctly!| $8 / $14|
| Thread Cutters | O | Use these for cutting your thread in the hard to reach places without running the risk of damaging your project. | Scissors work for cutting thread and the xacto blade can work for cutting thread inside your projects -- just be careful! | $3.95 / $39 |
| Maul | O | Used for end punches, rivets, snaps, chisels, or irons. | You really only need one of these if you are planning on doing any of the activities mentioned previously. | $20 / $55 |
| Pricking Iron/Chisel | O | Use these to mark or punch your holes instead of an overstitch wheel and awl. I prefer using the overstitch wheel and awl but others like the irons/chisels. | There is a big difference between irons vs. chisels, diamond vs. lacing. They all produce different results. Definitely ask before purchasing! The ones I linked are very different.| $12 / $259|
| Creaser | O | Used for decorative creases on things like card slots. | Definitely optional and definitely personal preference. | $14.40 / $72 |
| Wax | O | Used for burnishing. Gives the edges a nice seal. | The $10 is my top secret wax I use. I bought a bunch on sale for $5 and it is fantastic. | $4 / $10|
---