Reddit Reddit reviews Striveday™Flexible Silicone Wire 22awg Electric wire 22 gauge Coper Hook Up Wire 300V Cables electronic stranded wire cable electrics DIY BOX-1

We found 5 Reddit comments about Striveday™Flexible Silicone Wire 22awg Electric wire 22 gauge Coper Hook Up Wire 300V Cables electronic stranded wire cable electrics DIY BOX-1. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Electrical Equipment
Electrical Wire
Striveday™Flexible Silicone Wire 22awg Electric wire 22 gauge Coper Hook Up Wire 300V Cables electronic stranded wire cable electrics DIY BOX-1
Product Name :Silicone Wire; Wire Type :22AWG; Material : Silicone rubber , Tinning Copper; Voltage Rating: 300 Volts ,Rated temperature: -60 C - + 150 CWire Length :6M / 19.6Ft each colorExternal Color : Black red blue green yellow

5 Reddit comments about Striveday™Flexible Silicone Wire 22awg Electric wire 22 gauge Coper Hook Up Wire 300V Cables electronic stranded wire cable electrics DIY BOX-1:

u/TarmacFFS · 2 pointsr/electronics

It's pretty straight forward. Here are the parts I'm using:

  1. I bought this ATX plug so I didn't have to splice my power supply.
  2. Using this PWM controller
  3. Using these female banana plugs

    Those are the things I bought specifically for this project. The things I already had that helped are:

  4. I really like this flexible silicone wire.
  5. I use these USB connectors for various projects. Their pinout is .1" (2.54mm) and it comes with all kinds. Works well for slimming down a raspberry pi.
  6. I used one of these prototype boards to solder the usb receptacles and the LED to.
  7. I'm using a pink LED from this pack of assorted LEDs along either a 100ohm or 220ohm resistor, I can't remember.
  8. I use one of these DPDT switches to switch between power on w/ PWM and power on w/ power to the solder fume extractor.
  9. I used a JST connector from this JST kit to put a male header on the side so I can plug in accessories like the solder fume extractor.
  10. Lastly, the front panel is bolted on with some M3 screws from this assortment.
  11. The case was modeled in Rhino 5 and printed in a CR-10 using Silver eSun PLA+

    This post has made me realize I have way to much electronics stuff just lying around...
u/predzZzZzZ · 2 pointsr/arduino

This is something I use (Striveday™Flexible Silicone Wire 22awg Electric wire 22 gauge Coper Hook Up Wire 300V Cables electronic stranded wire cable electrics DIY BOX-1 https://www.amazon.com/dp/B01LH1FR6M/ref=cm_sw_r_cp_api_fsn3Ab1TTXV65) and you can flatten the wires on the breadboard and eventually solder on a final prototype if you want that

u/PeverseRolarity · 1 pointr/breadboard

People make those super clean looking breadboard setups using spools of wire like this:

https://www.amazon.com/StrivedayTMFlexible-Silicone-Electric-electronic-electrics/dp/B01LH1FR6M/

And something like this to bend the wire into shape:

https://www.amazon.com/Velleman-VTBEND1-Resistor-Component-Bending/dp/B00TSUXJ3I/

u/Tumdace · 1 pointr/headphones

I saw that guide and wanted to do it, but what sort of wire would you use for those twisted pairs?

https://www.amazon.ca/Striveday-Flexible-Silicone-Copper-Electric/dp/B01LH1FR6M/ref=sr_1_1?ie=UTF8&qid=1499781694&sr=8-1&keywords=22+awg+wire

Is this stuff any good?

u/notamedclosed · 1 pointr/fpv

Your VTX instructions seem pretty simple to follow. Lines drawn from pad to pad, just copy what it has there. You want small gauge wire for this stuff so 22 gauge should work fine IF it is stranded silicon covered wire. You can buy kits of wire with multiple colors easily enough off amazon.

Other types of wire can be too brittle, the insulation will tend to burn and retract when soldering which can leave the wire too exposed. Silicone and stranded is the way to go. Like this.

The important part is to double and triple check your connections are right, and do a continuity check or use a smoke stopper before you ever plug a battery in.