Reddit Reddit reviews T33 Inline Coconut Grade Activated Carbon Pre/Post Membrane Filter for Taste and Odor Reduction

We found 1 Reddit comments about T33 Inline Coconut Grade Activated Carbon Pre/Post Membrane Filter for Taste and Odor Reduction. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Replacement Water Filters
Replacement Under-Sink Water Filters
Kitchen & Bath Fixtures
Water Filtration & Softeners
T33 Inline Coconut Grade Activated Carbon Pre/Post Membrane Filter for Taste and Odor Reduction
💎 Inline Coconut Grade Activated Carbon Post Filter💎 THIS FILTER IS FOR a Standard Reverse Osmosis Water Filtration Unit or any type of Ice Machines, Water Coolers RV & Many Other Applications and WELL-MATCHED Models of Cartridges: Woder WD-10K, Watts 43000140, LASCO 37-1821, Omnipure K2533JJ and CL10ROT33-B, Culligan IC-100A, EZ-FLO 60461, AQUACREST GXRTDR, Hydronix ICF-10, iSpring FT15, APPLIED MEMBRANES H-F1032-43A, Express Water FLTINQ-V, WATTS-AICRO, Aquaboon T33, Naples Naturals SPR-PCF2510, Pentek GS-10-B💎 LIFETIME: REPLACE every 2 years, depending on the water quality💎 This Filter Is Wrapped & Sealed & Meets NSF Standards and Regulations. DIMENSIONS: 10" X 2"💎 WELL-FIT FOLLOWING REVERS OSMOSIS WATER FILTER SYSTEMS: iSpring RCC7, RCC7AK, RCC7U and RCC1UP, APEC ROES-PH75, Express Water ROALKUV10M, NU Aqua Platinum 799789985164, Geekpure RO5, Global Water RO-505, PureDrop RTW5, HiKiNS RO-125G
Check price on Amazon

1 Reddit comment about T33 Inline Coconut Grade Activated Carbon Pre/Post Membrane Filter for Taste and Odor Reduction:

u/GODZiGGA · 2 pointsr/HydroHomies

There is nothing proprietary about the filters and they are self-contained in their own disposable housing so there so assuming your system is using the standard 1/4" outside diameter water line tubing, you could easily add it to your system without needing to replace the entire thing.

All you would need is to get two sets (4 total fittings) 1/4" quick connect water filter fittings (which you reuse every time you change the filter) and the filters; pH filter post carbon filter (doesn't have to be these brands, any similar filter will do the trick if it is good quality). For install:

  1. Screw the quick connect adapters onto the filters.

  2. Shut off the water valve heading into the filters as well as the valve at the tank (same process as when you change the filters).

  3. Open the faucet to depressurize the system and get as much of the water out of the line as possible.

  4. Cut the line between the tank and the faucet.

  5. Connect the now split water line onto the quick connect adapters for the post carbon filter.

  6. Cut the line again between the faucet and post carbon filter.

  7. Connect the now split water line onto the quick connect adapters for the pH filter.

  8. Open up the water valves at the tank and heading into the system.

  9. Shut off the faucet when water starts coming out again.

    Worst case scenario is you might need additional 1/4" tubing if you don't currently have enough excess line to route the line to a place you can support the additional filters so the water line isn't supporting their weight and they aren't put in a position where the tubing can kink. They make filter clips so you can mount them on top of the RO filter and even each other if you are trying to figure out where to put them. The only reason I could see as to why you may need to replace the entire system is if you wanted to add an additional stage pre-RO filter as those housings are different so you can't just add an additional filter without swapping a 2-filter housing for a 3-filter housing and at that point it may be more economical to swap out the entire system.