(Part 2) Top products from r/FlashForge

⇧Jump to the top 20

We found 4 product mentions on r/FlashForge. We ranked the 23 resulting products by number of redditors who mentioned them. Here are the products ranked 21-40. You can also go back to the previous section.

21. Adda 96mm X 33mm New Blower 12V DC Waterproof to IP55 Ball Bearing Cooling Fan 2 pin

Sentiment score: 0
Number of reviews: 1
96x33mm 12VHigh Pressure .87InH2OWater resistant to IP55Ball Bearings52.2 dBA
Adda 96mm X 33mm New Blower 12V DC Waterproof to IP55 Ball Bearing Cooling Fan 2 pinShow Reddit reviews

22. uxcell 400mm x 205mm x 0.5mm Silicone Thermal Pad for CPU GPU Heatsink

Sentiment score: 2
Number of reviews: 1
Product Name : CPU Thermal Pad;Material : SiliconeSize : 40 x 20.5cm/15.7'' x 8.1'' (L*W)Thickness : 0.5mm/0.02''Weight : 103gPackage Content : 1 x CPU Thermal Pad
uxcell 400mm x 205mm x 0.5mm Silicone Thermal Pad for CPU GPU HeatsinkShow Reddit reviews

23. PHc 24 Volt 3 Amp Power Adapter, AC to DC, 2.1mm X 5.5mm Plug, Regulated UL 24v 3a Power Supply Wall Plug

Sentiment score: 0
Number of reviews: 1
AC Input: 100V to 240V, DC Output: 24 volt at 3 amp rating, UL, ROHS certifiedType: Regulated switching power supply with 2.1mm x 5.5mm plug, center positiveHigh quality commercial grade AC to DC power adapter for manufacturer of all typePlease confirm the plug size before purchaseTips: voltage must...
PHc 24 Volt 3 Amp Power Adapter, AC to DC, 2.1mm X 5.5mm Plug, Regulated UL 24v 3a Power Supply Wall PlugShow Reddit reviews
Next page

Top comments that mention products on r/FlashForge:

u/IcanCwhatUsay · 2 pointsr/FlashForge
  • Remove the right extruder

  • Add a offset spacer to the right side of the left extruder - extruder will crash if you don't do this as it can't reach the limit switch before the carriage hits the bracket

  • Add the Dreamer fan or similar to the left side - optional, you just need cooling

  • get a single extruder carriage. I got mine from from Raffle.ch who is no longer in business. Just search single extruder carriage for makerbot replicator 2x or something to that and tons will come up. I'd recommend aluminum, but only because I didn't trust the plastic options.

  • Longer X belt - GT2 I believe, amazon has tons of options

  • 8x12 borocilicate plate from Mcmaster PN : 8476K84

  • Silicone Thermal Pad - This distributes the heat a bit better since you'll have a good amount of overhang. amazon

  • Kapton tape - Place a layer sticky side down on the steel/ceramic bp, Make sure it's nice and flat, then stick the silicone pad to the bottom of the Glass BP, then stick that to the kapton. It won't move after that but it can be removed if needed. (Don't ask, it just works rediculously well)

  • Glass BP offset https://www.thingiverse.com/thing:452367

  • and then the tough part, you have to tweak the slicer settings to recognize that it has a larger BP. I'd shoot you my Simplified 3D settings but I'm not at home. It's not too complicated but I recall having a hard time with it. Flashforges uses the center of the BP as 0 and not the front left corner like repraps. So you'll have to do a little thinking here. Also, the tool head has an offset, I don't recall if the right extruder is 0 or -XXmm but you'll have to take that into account too.

  • Last thing you'll need is to cut your heatsink in half, the big aluminum bar that the hot ends fit in. make sure you cut it such that you have the two holes for the strain relief screws still intact, you'll need these for the offset spacer.
u/twingivings · 1 pointr/FlashForge

Sadly it's a blower fan like This which runs at 12v. I'll find it's info when I'm back home.

u/pug1gaming1 · 1 pointr/FlashForge

This should work, I'll check the plug size and reply to this post again. (The connector may be incorrect size, but polarity is positive) here you go
https://www.amazon.com/PHC-Power-Adapter-Regulated-Supply/dp/B006XIPER2